F.I.T. Bunny LED User manual

F.I.T. Bunny LED
2 x 300
Beam Angle
Battery Li-Ion 18650
Run Time
100% Intensity(100 mins)
50% Intensity(280 mins)
25% Intensity(450 mins)
Depth Rating 60m
LEDSpec White 4xCREE XM-L2U2
LEDLife 50000 hr
Material Aircraft grade aluminum
Coating Hard Anodized
Dimension
Weight
Mode 3-way output switch：100%、50%、25%
Index
1、Specification
2、Operation
3、Warranty
1.Specification
1. Bunny LED 2. 18650Li-Ion
2.Operation
2.1 Installing the battery
Flood Output
(2LED)
Power
Indicator
Left Button
2.1.1 Turn the Bunny LED cap counter-clockwise.
2.1.2 Insert the 18650 battery as shown in the picture.
Make sure the battery is facing the correct direction.
2.1.3 Align the battery compartment to the cap and close.
★Note：Turn the battery cap till it is
fully close to prevent flooding
89.8(W) x 465 (L)mm
Air 410g / Water 185g(incl battery)
43
2
Fig.2 Light Head
1.2 Functional Specification
Fig.1 Construction
1.3 Package Contents
Fig 3. Package Contents
Fig 4. Installing the battery
Light Head
Lumens
Hot Shoe
Base
1/4 Loc-lin
110 degree
Right Button
Battery Cap
12 3 4 5 6
3. Charger
4.O-Ring x 2 5. Grease 6.Snoot x 2

5
2.8Grease Application
2.9 Changing of O-Ring
Any deformation, damage or expansion found, replace the damaged
O-Ring provided. Remove the damaged O-Ring and do not use
sharp objects as tools. Clean the O-Ring grooves and keep the new
O-Rings with grease in place and protect from outer debris.
2.10 Note
★Do not use other battery than specified.
★Do not attempt to open the battery cap when
underwater.
★Remove the battery if Bunny LED not in use
for a prolonged period.
3.Product Warranty
3.1 Quality Assurance
2.4 To prevent overheating
The Bunny LED is engineered with a temperature sensor
to prevent overheating by setting the light in low
brightness mode.
2.5 Battery status
4 battery status: Green-Full,Yelow-Half,
Red-Low ,Blink RED-Extremely low,light will be
turned off automatically after 10 mins.
2.6 Low Battery Protection
To save battery, Bunny LED enters a low
brightness mode when RED LED is on. Light will be
turned off automatically after 20 mins.
2.7 Using the Charger
Use the grease provided to apply on the O-Ring to
ensure smooth operation of the O-Ring. Remove any dirt
or hair before application.
6
1. Modification, damaged or dismantled
2. Wrong operation,i.e. wrong type of battery
3. Short circuit due to flooding
4. Natural occurrences beyond human control
3.2 Trobleshooting
Problem Solution
LED fail
to light up
Check battery direction.
Check if battery is low on power.
Check if cap is fully closed.
Green LED lights
up the moment
charging commences
To install battery properly.
Place battery on the right side.
Contact between charger and battery?
Water found
inside the light
Check the orings to see if there is
dirt or not installed properly.
8
1.The Micro USB port of the charger is for 5V/1A
Micro USB charger to charge the battery.
2.Power indicator will show the battery status.
3.The USB output port of the charger is for charging
other 5V 1A device via USB cord.
4.To protect battery and elongate battery
life,please don't charge the battery for more than 12
hrs.
Battery Power Indicator
Power Indicator
Button
Charger
ON：
Whit light off, press left button for 2 seconds
to turn on the left LED (default intensity: 100%).
Or press right button for 2 seconds to turn on the
right LED (default intensity: 100%).
Using these 2 buttons, you could independently control
the left/right LED.
Brightness：
With light on, press left button for 1 second
to change brightness of left LED:white 100%→white 50%
→white 25%→white 100%. Press right button
for 1 second to change brightness of right LED:
white 100% →white 50% →white 25%→white 100%.
OFF：
1.With light on / with one side of LED on /
in temperature protection mode, or in low volt
status,press button of the LED which is on
for 3 seconds to turn off the light.
2.With light off,or with both LEDs off,press any
button for 5 seconds to turn off both LEDs（one LED
will be off first, then the other one will be off).
2.3 Operation
Charger Plug
2.7.1 Ensure the correct method of inserting the
battery onto the charger.
2.7.2 Once battery installed, plug the charger
cable to the power source to commence charging,
indicator will blink. Green indicator lit up once
charging completed.（Charge time: 3 hrs）
Note:
18650 Li-Ion Battery
Mobile Phone Charger (5V 1A)
Power Cord
DC Charger Plug
Micro USB charging slot
USB output port
For a period of 15 days from the date of retail purchase, your local
retailer will exchange the product with a new one if a hardware defect
arises. This warranty is valid for 1 year and free servicing will be
offered if any problem occurs within that year (Batteries are
warranted for 3 months).You may be responsible for shipping and
handling charges if warranty is invalid.
This warranty does not apply: 7
Please refer to the table below to do a verification check and
confirm it is a defect before returning to the supplier.