Traxon ARCHISHAPE Dot 2.0 S CE User manual

Black score dimension 148 x 210 mm
• Please read instruction carefully before
assembling and installation
• Please keep instruction as reference in the future

"3$)*4)"1&¥%PU4.-$&
15038534 ARCHISHAPE 2.0 Dot S_M_L UI v9.indd 1 PM
12/10/2023 16:32

2 3
Black score dimension 148 x 210 mm Black score dimension 148 x 210 mm
ARCHISHAPE®2.0 Dot S/M/L ARCHISHAPE®2.0 Dot S/M/L
Wattage
(W)
Rated voltage
(V)
Weight
(g) TaIP
AS 2.0 Dot S RGB/RGBW 1 15V DC 28.2
-20~50°C66, 67
1AS 2.0 Dot S DW/W 15V DC 28.2
AS 2.0 Dot M RGB/DW/W 2 24V DC 66.9
2AS 2.0 Dot M RGBW 15V DC 66.9
AS 2.0 Dot L RGB 3 15V DC 73.6
3AS 2.0 Dot L DW 15V DC 73.6
Max. connected qty.
RGB RGBW
S 110 110
M98 55
L43 62
Above calculation is based on standard pixel pitch and 5m lead cable with 320W power supply. Please
consult local sales for other configurations.
21
3a 4a
5a 3b
AS 2.0 Dot S mounting
AS 2.0 Dot M/L mounting
“click”
15038534 ARCHISHAPE 2.0 Dot S_M_L UI v.indd 2-3
W
LH
H
W
L
H
W
L
AS 2.0 Dot S RGB/
AS 2.0 Dot S RGBW
AS 2.0 Dot M RGB/
AS 2.0 Dot M RGBW
AS 2.0 Dot L RGB/
AS 2.0 Dot L RGBW
W1 W1 W1
W2
W2
WW1W2 L H
26mm 12mm NA 53mm 1 mm
52.2mm 12mm 40mm 67.7mm 14mm
55mm 12mm 45mm 70.7mm 14mm
AS 2.0 Dot S RGB/AS 2.0 Dot S
AS 2.0 Dot M RGB/AS 2.0 Dot M
AS 2.0 Dot L RGB/AS 2.0 Dot L
mm
mm
mm
W3
NA
41mm
41mm
W3 W3
DW
85
86
33
W
110
86
62
3AS 2.0 Dot L RGBW/W 24V DC 73.6
12/10/2023 16:32 PM

4 5
Black score dimension 148 x 210 mm Black score dimension 148 x 210 mm
ARCHISHAPE®2.0 Dot S/M/L ARCHISHAPE®2.0 Dot S/M/L
System diagram (Basic)
System diagram (Power injection)
System diagram (Auto-addressing module)
15038534 ARCHISHAPE 2.0 Dot S_M_L UI v .indd 4-5
Power supply connection needs to
be done in indoor environment
S
M
L
S
M
L
S
M
L
PM
End Cap (Resistor)
DMX In
AC in
RJ45 POWER INJ CABLE KIT
LED Engine 15/24V
POWER INJ CABLE KIT
Power injection is required when the number of connected dots reaches the maximum value.
DMX In
AC in
End Cap (Resistor)
RJ45 POWER INJ CABLE KIT
AC in
LED Engine 15/24V
LED Engine 15/24V
Auto-addressing
module End Cap (Resistor)
DMX In
AC in
RJ45 POWER INJ CABLE KIT
LED Engine 15/24V
After connecting the cables, tangle up with water-proof tapes for
extra protection.
Minimum Bending Radius is 4 x D (Round Cable Diameter) or 4 x T (Flat Cable Thickness), Non-Bendable Length
is 50mm from the connector overmold end and 20mm from Dot.
12/10/2023 16:32
D
Ø9.5mm/0.37”
50mm/1.97”
(Minimum Bending Radius)
≥
4D
Non-Bendable/
Non-twistable Length
Non-Bendable /
Non-twistable Length
Minimum clearance
from dot
20mm/0.79”
(Minimum
Bending Radius)
≥
4T
T

6
Black score dimension 148 x 210 mm
A
RCHISHAPE®2.0 Dot S/M/L
WARNINGǖ
1. The luminaire should be installed and maintained by qualified electrician and wired in
accordance with the latest IEE electrical regulations or the national regulations. Terminal block
not included. Installation may require advice from a qualified person.
2. Make sure the products are grounded.
3. The power must be OFF during installation and maintenance.
4. The external flexible cable or cord of this luminaire cannot be replaced. If the cord is damaged,
the luminaire shall be destroyed.
5. The light source of this luminaire can not be exchanged; if the user needs to exchange the light
source (e.g. the light source is at the end of its life cycle), then the completed luminaire has to
be exchanged.
6. Installation: Surfac e mounted. Outdoor use. No mounting height limited.
7. Make sure the products are securely installed.
8. The housing might become hot during or after operation.
9. No modification on the product is allowed.
10. Suitable for indoor and outdoor use. Do not immerse in water.
11. For DMX version, reinforced insulation has been complied between LV supply and control
conductors.
12. Not suitable for ordinary lighting in household room illumination.
13. Power supply system should be equipped with SPD (Surge protection Device) accordance
with electrical regulations.
C10449057
G15038534
31012
!
Conformance to:
INSTRUCTIONǖ
1. Order all power supplies / cables / addressers / modules / end caps separately.
2. Connect luminaires to main power supply & DMX cable by IP66 junction box (purchased by customer).
Make sure the wiring is correct and reliable. Suggest to wrap the connectors by waterproofed tape for security.
3. Suggest to use shielded twisted-pair as signal cable. Use end cap with 120 ohm resistor to get stable DMX
signal.
4. DMX version requires addressing tool or auto-addressing module to address the luminaires.
5. Regular check is required.
6. Do not stare at the operating light source. The luminaire should be positioned so that prolonged staring into the
luminaire at a distance closer than 2m is not expected.
15038534 ARCHISHAPE 2.0 Dot S_M_L UI v.indd 6-7 PM
IEC 60598-2-20
IEC 60598-2-1
Luminaries - Part 2-20: Particular requirements -
Lighting chains
Luminaries - Part 2: Particular requirements.
Section One: Fixed general purpose luminaires
12/10/2023 16:32
Traxon Technologies Ltd.
Room 113, 1/F, Wireless Centre, 3 Science Park East Avenue, Shatin, New Territories, Hong Kong
Traxon Technologies Europe GmbH
Karl-Schurz-Str. 38, 33100 Paderborn, Germany
Traxon Lighting Company Limited
B402 - B421, Building 6, Northwest Shenjiu Science and Technology Pioneer Park, the intersection of
Taohua Road and Binglang Road, Fubao Community, Fubao Street, Futian District, Shenzhen
卓生照明有限公司
深圳市福田区福保街道福保社区桃花路与槟榔道交汇处西北深九科技创业园 6 号楼 B402- B421
卓生照明有限公司
深圳市福田區福保街道福保社區桃花路與檳榔道交匯處西北深九科技創業園 6 號樓 B402- B421
www.traxon-ecue.com