FAAC XBFA ON User manual

2
1
4
5
1
2
1
1
2
1
2
1
2
1
2
1
1
2
1
2
1
1
1
1
2
FAAC S.p.A . - Via Calari, 10 40069 Zola Predosa - Italia - tel. [phone] - fax. [phone] - www.faacgroup.com
Manufactured by: BEA SA - LIEGE Science Park - Allée des Noisetiers 5 - 4031 Angleur - Belgium - T [phone] - F [phone] - [e-mail] - www.bea.be
©
BEA
|
O
ri
g
ina
l
instructions
|
42
.7
859
/
V1
-
06
.1
3
BEA hereby declares that the FAAC XBFA ON is in conformity with the basic requirements and the other relevant provisions
of the directives 2004/108/EC and 2006/42/EC.
Notified Body for EC inspection: 0044 - TÜV NORD CERT GmbH, Langemarckstr. 20, D-45141 Essen
Angleur, June 2013 Pierre Gardier, Authorized representative and responsible for technical documentation
LED-SIGNALS
Only for EC countries: According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE)
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOUR PRINTING
The ORANGE LED
flashes 1 x.
The ORANGE LED
flashes 2 x.
The ORANGE LED
flashes 4 x.
The ORANGE LED
flashes 5 x.
The ORANGE LED
is on.
The RED LED flashes
quickly after an
assisted setup.
The RED LED
lights up
sporadically.
The LED is off.
The reaction of
the door does not
correspond to the
LED-signal.
The ORANGE LED
flashes quickly.
The sensor signals
an internal fault.
Irregularities in the
power supply
The sensor receives
not enough IR-energy.
The sensor receives
too much IR-energy.
The sensor encounters
a memory problem.
The sensor vibrates.
The sensor sees the door
during the assisted setup.
The sensor sees the door.
The sensor is disturbed by
lamps or another sensor.
The sensor is disturbed
by the rain.
A DIP-switch was changed
without confirmation.
Check power supply.
Check wiring.
Use the 1 m prism if possible (accessory).
Check the angle of the IR-curtains.
Cut and restore power supply.
If orange LED lights up again, replace sensor.
Check the angle of the IR-curtains.
Launch a new assisted setup.
Attention: Do not stand in the detection field!
Change the output configuration (DIP 4).
Use a low energy prism if possible (accessory).
Check the angle of the IR-curtains.
Check if the sensor is fastened firmly.
Check position of prism and cover.
Choose a different frequency (DIP 2).
Choose the critical environment presetting (DIP 1).
Launch an assisted setup and adjust the IR angle.
Cut and restore power supply.
If orange LED flashes again, replace sensor.
Check connections to test output.
If your door controller is not able to test the sensor,
connect the red and blue cable to the power supply.*
Confirm the DIP-settings by a long push on the
push button.
*excludes EN 16005-conformity of the door system
XBFA ON
1
2
6
3
4
5
1. cover
2. IR-prism (2 m)
3. main connector
DESCRIPTION
ENGLISH
Safety sensor
for automatic sliding doors
4. IR-angle adjustment
5. push button for setup or DIP-setting confirmation
6. DIP-switch
User’s Guide for product version 0100 and higher
See product label for serial number
TECHNICAL SPECIFICATIONS
Presence
Typical response time: <256 ms
Active infrared with background analysis
Spot diameter: 0.1 m (typ)
Number of spots: 24
Number of curtains: 2
From -4 ° to +4 ° (adjustable)
Solid-state-relay
(free of potential, free of polarity)
Max. contact current: 100 mA
Max. contact voltage: 42 V AC/DC
0.3 s to 1 s (not adjustable)
Typical: < 5 ms
12 V - 30 V DC -5%/+10% (to be operated from SELV compatible power supplies only)
< 1.6 W
1.8 m to 3 m
< 1 V : Log. L; > 10 V: Log. H (max. 30 V)
-25 °C to +55 °C
IP54
< 70 dB
20 years
MD 2006/42/EC; ROHS 2 2011/65/EU; EN 16005:2012; EN 12978:2009;
EN IEC 62061:2005 SIL2; EN 61496-1:2012 ESPE Type 2; EN ISO 13849-1:2008 Pl «c» CAT.2
(under the condition that the door control system monitors the sensor at least once per door cycle)
Supply voltage:
Power consumption:
Mounting height:
Sensitivity of the test input:
Temperature range:
Degree of protection:
Noise:
Expected lifetime:
Norm conformity:
Detection mode:
Technology:
Angle:
Output:
Hold time output signal:
Response time on test request:
S
pecifications are subject to changes without prior notice. All values measured in specific conditions.
RED
LED

1
2
0
1
2
12
0
1
2
33
0
1
2
12
0
1
2
33
0
1
0
1
2
«click»
1
1
H
W
H
W
2 m 1 m
max.
5 cm
max. 5 cm
+
-
+
-
MOUNTING & WIRING
INFRARED FIELD - SAFETY
GREEN
BROWN
YELLOW
WHITE
PINK
GREY
RED2
BLUE2
POWER SUPPLY
OPENING INPUT
SAFETY INPUT
TEST
OUTPUT
WIDTH
RED
LED
1Output status when sensor is operational
2For compliance with EN 16005, connection
to door controller test output is required.
The door control unit and the door cover profile must be correctly earthed.
SENSOR
HW
2.20 m 2.30 m
2.50 m 2.55 m
3.00 m 2.80 m
HW
2.20 m 1.20 m
2.50 m 1.40 m
3.00 m 1.60 m
Depth of curtain: 8-10 cm
Depth of safety field: 25 cm*
RELAY R1
RELAY R2
12-30 V DC
Check position of IR-curtains with
Spotfinder and adjust if necessary.
DOOR
Detection field width indicated according to conditions defined in EN 16005 and including dimension of test body CA.
Available as accessory
ANGLE
CLOSER
CLOSER
AWAY
AWAY
ORANGE
* in standard presetting
The size of the detection field varies according to the mounting height of the sensor.
3
4
+
+
A
B
Launch an ASSISTED SETUP to verify wiring, position of the
curtains and correct functioning of the sensor.
SETTINGS (by DIP-switch)
QUICK SETUP ASSISTED SETUP
SETUP
OPEN+CLOSE RED-GREEN OFF
RED-GREEN OFF
Step outside of the detection field before launching a setup.
LONG (> 3s)
LONG
SHORT
standard
critical
environment
standard
extreme 1
1Enhanced IR-immunity which excludes EN 16005-conformity of the door. system.
LONG (> 3s)
critical environment: enhanced immunity for critical environments (rain, snow, lamps...). Only 1 IR-curtain activated.
standard: standard environments (factory setting)
NC
NO
The yellow and white wires have to be connected to launch an
assisted setup.
After changing a DIP-switch, the orange LED flashes.
A LONG push on the push button confirms the setting.
Always launch a setup after changes of the DIP-settings.
- Test the good functioning of the installation before leaving the premises.
- The manufacturer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system
in compliance with applicable national and international regulations and standards on door safety and if applicable, the machinery
directive 2006/42/EC.
- The device cannot be used for purposes other than its intended use. All other uses cannot be guaranteed by the manufacturer
of the sensor.
- The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor.
- Only trained and qualified personnel may install and setup the sensor.
- The warranty is void if unauthorized repairs are made or attempted by unauthorized personnel.
- Avoid touching any electronic and optical components, avoid vibrations, do not cover the sensor and avoid proximity to
neon lamps or moving objects.
- It is recommended to clean the optical parts at least once a year or more often if required due to environmental conditions.
SAFETY INSTRUCTIONS
PRESETTINGS ENVIRONMENT R2 CONFIGURATIONFREQUENCY
ORANGE OFF