FAAC TM XTT 433 R User manual

TM XTT 433 R

2
ENGLISH
CE DECLARATION OF CONFORMITY
Manufacturer: FAAC S.p.A.
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
Declares that: TM XTT 433 R
• conforms to the essential safety requirements of the following EEC directives
99/5/CE R&TTE
CE 0470
Additional note:
This product underwent tests in a typical uniform configuration
(all products manufactured by FAAC S.p.A.).
Bologna, 01 January 2010
The Managing Director
A.Marcellan
1) ATTENTION! To ensure the safety of people, it is
important that you read all the following instructions.
Incorrect installation or incorrect use of the product
could cause serious harm to people.
2) Carefully read the instructions before starting up the
device.
3) Do not leave packing materials (plastic, polystyrene,
etc.) within reach of children as such materials are
potential sources of danger.
4) Store these instructions for future reference.
5) This product was designed and built strictly for the use
indicated in this documentation. Any other use, not
expressly indicated here, could compromise the good
condition/operation of the product and/or be a source
of danger.
6) FAAC declines all liability caused by improper use or
use other than that for which the automated system
was intended.
7) Do not install the equipment in an explosive atmosphere:
the presence of inflammable gas or fumes is a serious
danger to safety.
8) FAAC declines all liability as concerns safety and
efficient operation of the automated system, if system
components not produced by FAAC are used.
9) For maintenance, strictly use original parts by FAAC.
10) Do not in any way modify the components of the
automated system.
11) Keep remote controls or other pulse generators away
from children, to prevent the system from being activated
involuntarily.
12) The user must not attempt any kind of repair or direct
action whatever and contact qualified personnel only.
13) Anything not expressly specified in these instructions
is not permitted.
GENERAL WARNINGS
GENERAL SAFETY OBLIGATIONS

3
4
4
4
4
5
5
5
6
6
6
6
7
7
8
10
10
11
12
13
13
13
14
15
15
15
16
16
17
17
17
20
21
23
23
24
24
24
24
24
ENGLISH
Index
INDEX
1 GENERAL INFORMATION...................................................................................................................................
1.1 Radio waves propagation index..................................................................................................................
2 USE COMPLIANT WITH REGULATIONS ...............................................................................................................
3 DESCRIPTION ....................................................................................................................................................
3.1 Description of the TM XTT 433 R timer ........................................................................................................
3.2 Keys ..............................................................................................................................................................
3.3 Display..........................................................................................................................................................
3.4 ID Label .......................................................................................................................................................
4 TECHNICAL SPECIFICATIONS ...........................................................................................................................
4.1 Dimensions ...................................................................................................................................................
4.2 Technical specifications ..............................................................................................................................
5 INSTALLATION ...................................................................................................................................................
6 OPERATION .......................................................................................................................................................
6.1 Setting the time and date............................................................................................................................
6.2 ASSOCIATING THE TM XTT 4334 timer WITH THE MOTOR ...............................................................................
6.3 Adding a TM XTT 433 R timer .......................................................................................................................
6.4 Deleting a motor from a group ...................................................................................................................
6.5 Deleting a single channel from a motor .....................................................................................................
7 INFORMATION ON USE ....................................................................................................................................
7.1 Memorising the preferred position (Only for TM xx ER-ERO)........................................................................
7.2 Changing the preferred position (Only for TM xx ER-ERO)...........................................................................
7.3 Choosing the mode (user menu) .................................................................................................................
7.3.1 Operation in manual mode ......................................................................................................................
7.3.1.1 Operation in manual mode with sun sensor enabled...........................................................................
7.3.2 Operation in automatic mode..................................................................................................................
7.3.3 Operation in “automatic + Holiday” mode..............................................................................................
7.3.4 Operation in “automatic + Planetary” mode ..........................................................................................
7.3.5 Operation in “automatic + Holiday + Planetary” mode .........................................................................
7.4 Programming the FUNCTIONS......................................................................................................................
7.4.1 Setting the automatic function (command setting) ...............................................................................
7.4.2 Setting “Holiday” .....................................................................................................................................
7.4.3 Setting “Planetary” .................................................................................................................................
7.5 Keypad lock .................................................................................................................................................
8 REPLACING THE BATTERY ..................................................................................................................................
9 TROUBLESHOOTING .........................................................................................................................................
10 DISPOSAL ......................................................................................................................................................
11 WARRANTY .....................................................................................................................................................
12 COMPLIANCE.................................................................................................................................................
13 CUSTOMER SERVICE.......................................................................................................................................

4
ENGLISH
3 DESCRIPTION
1 GENERAL INFORMATION
2 USE COMPLIANT WITH REGULATIONS
The TM XTT 433 R timer for remote control operates on a frequency of 433.92 MHz that is also used for other radio
services. Therefore, in case of equipment that works on the same (or similar) frequency, there is the risk of compromising
correct operation of the device and limiting its range of action.
The reception power of the radio controls can be affected by many factors:
Where it is fitted;
Not having eliminated the radio interference generated by other devices and systems;
Presence of other transmitters in the frequency range of the control unit;
Weather conditions, etc.
•
•
•
•
The TM XTT 433 R XXXX remote control timer has been designed and developed exclusively for controlling radio-con-
trolled roller shutters using a time switch, according to the laws in force.
No other use is permitted unless otherwise expressly authorised by the manufacturer. Therefore the manufacturer is
relieved of any responsibility that may result from not following these instructions.
The manufacturer is not liable for consequences deriving from incorrect installation and improper use of the product
due to:
Work conditions that are not within the limits indicated in the technical specifications;
Improper installation;
Negligent maintenance;
Weather conditions;
Acts of vandalism.
•
•
•
•
•
The TM XTT 433 R timer is designed to be mounted on a wall and is used to control, with the timer switch, operation
time of automated motor-driven devices; e.g. sun blinds, roller shutters, shutters.
The device features 6 individually coded radio channels for sending six different signals and individually controlling six
different groups of motor-driven roller shutters.
It is also possible to send six different radio commands at one time, so that six different groups of motor-driven roller
shutters can be controlled simultaneously (group function).
The TM XTT 433 R timer can be operated in the following modes:
manual;
Automatic with operation time programming together with “Holiday” and “Planetary” mode;
Automatic with operation time programming;
Automatic with operation time programming together with “Holiday” mode;
Automatic with operation time programming together with “Planetary” mode;
Manual with a “Sun sensor” enable/disable option
With the automatic modes, the following functions can be programmed:
24 hr (day function) or 1 week (week function) commutation period;
Separate commutation periods for each radiochannel as well as for each day of the week, or for different days
of the week (from Monday to Friday and Saturday/Sunday).
•
•
•
•
•
•
•
•
1.1 Radio waves propagation index
Plaster, wood,
plasterboard
from 90 to 100%
Reinforced
concrete
from 10 to 70%
Brick,
agglomerate
from 65 to 95%
Metal, metal
protection
from 0 to 10%
TM XTT 433 R (132115) TIMER

5
ENGLISH
3.1 Description of the TM XTT 433 R timer
3.2 Keys
3.3 Display
SIGNAL SENDING
KEY LOCK * SUN SENSOR
MANUAL
MODE
PROGRAMMING
MODE
TIME FORMAT
UP
INDICATOR
DOWN
INDICATOR
FUNCTIONS
DAYS
OF THE WEEK
TIME/DATE
SETTING
PREFERRED
POSITION
INDICATOR
EXIT
RADIO CHANNEL INDICATOR
(* when the channel appears the state of the radio sensor is also displayed)
FLAT BATTERY
FUNCTION CHANGE KEY
UP KEY ( *** opening for shutters)
DOWN KEY ( ** closing for shutters)
STOP
PREFERRED POSITION
CONFIRM
RADIO CHANNEL SELECTION KEY
(1 to 6 +TOTAL)
PROGRAMMING KEYCONTROL KEYS
BATTERY
WALL
MOUNT
DISPLAY
P
P

6
1485
85
A
D
E
F
BC
mm
ENGLISH
4 TECHNICAL SPECIFICATIONS
Work frequency 433,92 MHz ± 100 KHz
Power supply 3V CR2450 Lithium Battery
Exclusive use Motor-driven roller shutters
Operating ambient temperature 0° C.........+40°C
Protection class IP 20
This product complies with Directive
99/05/EEC
A - MODEL ID CODE
B - PRODUCTION LOT ID NUMBER
C - READ THE INSTRUCTIONS
D - NOTIFIED BODY REFERENCE
E - CE MARK
F - DISPOSE OF ACCORDING TO THE REGULATIONS IN FORCE
4.1 Dimensions
4.2 Technical specifications
3.4 ID Label

7
2
3*
1
4*
ENGLISH
5 INSTALLATION
Designed for installation on an indoor wall with flat surface.
Avoid installing:
behind doors;
near sources of heat;
in a box with compartments;
in a metal container;
directly near large metal objects;
on or near the floor.
In areas with excessive humidity degree
Proceed as follows:
Remove the wall mount 1from the TM XTT 433 R timer 2and use it to mark the drilling holes on the wall on which
you wish to install the device.
Drill the holes in the wall and fix the mount 1using the provided screws 3and dowels 4(*not supplied)
Insert and lower the TM XTT 433 R timer 2to hook it onto the mount 1.
•
•
•
•
•
•
•
1.
2.
3.
6 OPERATION
When removed from its packaging, the TM XTT 433 R timer is ready to use. When it is turned on, the TM XTT 433 R timer
is set to operate in manual mode.
To operate the device, follow the instructions below:
put the battery in the TMXTT433R
set the time and day of the week
memorise the radio channels;
select and set the commands for each day.
1.
2.
3.
4.
Do not use solvents to clean the
TM XTT433 R timer
Do not exert heavy pressure on the
display
•
•

8
ENGLISH
6.1 Setting the time and date
Proceed as follows:
TIME
If you are not in programming mode
(Prog off), press the key for 5 seconds.
Prog will flash, press the key.
1.
Select the programming functions by pressing the
key, until the time programming symbol is
displayed.
will flash.
2.
3.
Press the key to set the AM/PM or 24 hr time format.
Use the or key to set the desired parameter and
confirm by pressing .
4.
Set the hour using the or key to set the
desired parameter and confirm by pressing .
Set the minutes using the or key to set the
desired parameter and confirm by pressing .
5.
6.
5 Sec.
If you are in the programming menu (Prog on) and no key is pressed for 1 minute, the TM XTT 433
R timer will go back to being automatically ready for operation. If you want to exit the menus
immediately, press for 5 seconds

9
ENGLISH
5 Sec.
Select the programming functions by repeatedly
pressing the ,key, until the date programming
symbol is displayed.
will flash.
Press the key to set the day ( d ), month ( m ),
year ( y ).
9.
10.
11.
I f y o u d o n o t w i s h t o c h a n g e o t h e r
programming parameters, repeatedly
press the key until EXIT is displayed
Exit will flash.
Press the key to exit the date and time settings.
DATE
Only i f y ou have e x ited th e p rogra m ming
mode (Prog off), press the key for 5 seconds.
Prog will flash, press the key.
7.
8.
Set the day using the or , key and confirm by
pressing .
Set the month using the or key and confirm by
pressing .
Set the year using the or ,key and confirm by
pressing .
I f y o u d o n o t w i s h t o c h a n g e o t h e r
programming parameters, repeatedly
press the key until EXIT is displayed.
Exit will flash.
Press the key to exit the date and time settings.
The days of the week will be displayed, starting from
Sunday, using the following abbreviations:
SU - Sunday
MO - Monday
TU - Tuesday
WE - Wednesday
TH - Thursday
FR - Friday
SA - Saturday
12.
13.
14.
15.
16.

10
ON
X 1
P
X 2
ENGLISH
6.2 ASSOCIATING THE TM XTT 4334 TIMER WITH THE MOTOR
6.3 Adding a TM XTT 433 R timer
Proceed as follows:
Press the key of a remote control that has
previously been memorised to select the radio
channel to which you wish to add a TM XTT 433 R
timer (NOTE: do only with multi-channel devices)
On the TM XTT 433 R timer you wish to add, press the
key to select the desired radio channel.
Move to the vicinity of the motor and power on.
1.
2.
3.
Within 10 seconds, on the remote control that has
already been memorised, press the programming
key P., for 2 seconds and after the key.
4.
On the TM XTT433 R timer, press the key within 5
seconds.
The motor will briefly turn twice in both directions to
confirm that memorisation has been completed.
5.
WITHIN
5 Sec.
2 Sec.
2 Sec.
WITHIN
5 Sec.
2 Sec.
WITHIN
10 Sec.
PREVIOUSLY MEMORISED
REMOTE CONTROL
NEW TM XTT 433 R
TIMER
PREVIOUSLY MEMORISED
REMOTE CONTROL
NEW TM XTT 433 R
TIMER
To memorise the TIMER in a motor, in which no other remote controls are memorised, please refer to the instructions
of the individual motor
In the event of more motors memorised
on the same remote control channel,
cut voltage to all motors except for the
motor to which you want to add the timer
to memorise.

11
X 1
X 2
P
ENGLISH
6.4 Deleting a motor from a group
Proceed as follows:
Press the key until Man is displayed
Press the key to select the desired radio channel
from which you wish to delete the motor.
1.
2.
Within 10 seconds press the programming key P
2 consecutive times (keep pressed for 2 seconds
each time).
3.
2 Sec.
EACH TIME
WITHIN
10 Sec.
Within 10 seconds press the key for 2 seconds.
The motor will briefly turn in both directions to confirm
deletion.
4.
Repeat the operations described above to delete
other motors from the same or other channels.
To guarantee correct channel
programming, you must power on and
consequently delete one motor at a
time.
5.
2 Sec.
You can individually select channels 1 to
6 or all of them simultaneously. The cir-
cle displayed will show the channel that
is currently in use.
If there is more than one motor memori-
sed on the same channel, power off all
the motors except for the one you wish to
delete from the memory.

12
X 1
X 2
P
ENGLISH
6.5 Deleting a single channel from a motor
Proceed as follows:
Press the key until you have reached the Man
function
Press the key to select the channel you wish to
delete.
Move to the vicinity of the motor.
1.
2.
3.
2 Sec.
EACH TIME
WITHIN
10 Sec.
2 Sec.
Within 10 seconds press the key for 2 seconds.
The motor will briefly turn in both directions to confirm
deletion of the TM XTT 433 R timer.
5.
Press the programming key P2 consecutive
times and keep pressed for 2 seconds each time.
4.

13
X 2
X 1
ENGLISH
7 INFORMATION ON USE
7.1 Memorising the preferred position (Only for TM xx ER-ERO)
It is possible to select a preferred position on the motor,
which can be reached both in manual mode by pressing
the , key and by programming it on one or more
channels at set times for each day of the week.
No preferred position is factory set.
Press the key until you have reached the Man
function
Press the key to select the radio channel
associated with the motor
You can individually select channels 1 to 6 or all of
them simultaneously. The circle displayed will show
the channel that is currently in use.
Press the or key to move the roller shutter until
you have reached the “preferred position” and press
for one second to stop it
Press the key for 5 seconds to memorise the
position.
The motor will briefly turn twice in both directions to
confirm that memorisation has been completed.
1.
2.
3.
4.
5 Sec.
7.2 Changing the preferred position (Only for TM xx ER-ERO)
Proceed as follows:
Press the key until you have reached the Man
function
Press the key to select the radio channel
associated with the motor
You can individually select channels 1 to 6 or all of
them simultaneously. The circle displayed will show
the channel that is currently in use.
Press the key for 5 seconds to delete the
“preferred position”.
The motor will briefly turn in both directions to confirm
deletion.
To memorise a new “preferred position”, repeat the
steps described in the paragraph “Memorising the
preferred position”.
1.
2.
3.
4.
5 Sec.

14
ENGLISH
7.3 Choosing the mode (user menu)
Check the display to ensure that you are in user mode
(Prog off).
Press the key repeatedly to scroll through the various
modes:
1. Manual
2. Automatic;
3. Automatic + holiday;
4. Automatic + planetary;
5. Automatic + holiday +
planetary.
The selected mode will be enabled when its symbol appears on the display, without the need to
press any keys for confirmation.
To change mode, repeat the steps described above.
In case the Prog icon is on, wait 1 minute to exit the settings menu or press for 5 seconds.

15
ENGLISH
7.3.1.1 Operation in manual mode with sun sensor enabled
The sun sensor function lets you automatically enable motor movement with the help of a brightness sensor instal-
led externally.
Proceed as follows:
Press the key to select the desired radio channel on which you wish to enable/disable the function.
You can individually select channels 1 to 6 or all of them simultaneously. The circle displayed will show the
channel that is currently in use.
Press the key to enable the sun sensor.
The symbol will be displayed.
To disable the sun sensor, select the desired channel and press the key.
The symbol will be displayed.
1.
2.
3.
7.3.2 Operation in automatic mode
In automatic operation mode, the TM XTT 433R timer automatically activates the motors, according to the set time.
To set the mode, see par. 7.4.1
Proceed as follows:
To activate automatic mode movement, you must first repeatedly press the key until is displayed.1.
1) With the sun sensor enabled, the manual control and programmed commands do not
work. The sun sensor has command priority over all the channels in which it has been set.
2) When the or symbols are on, it is not possible to change the function in the
user menu (wait for power off)
7.3.1 Operation in manual mode
Manual operation lets you send commands using
the Up, Down, Preferred Position, and Stop keys
directly from the timer to the associated motor.
Proceed as follows:
Press the key to select the desired radio
channel on which you wish to enable/disable
a function.
You can individually select channels 1 to 6 or
all of them simultaneously. The circle displayed
will show the channel that is currently in use.
Give the desired command to the motor (Up;
Down; Preferred Position)
1.
2.
SUN SENSOR ON SUN SENSOR OFF

16
ENGLISH
7.3.4 Operation in “automatic + planetary” mode
7.3.3 Operation in “automatic + holiday” mode
When in automatic + planetary mode, the TM XTT 433 R timer automatically activates the motors according to the
set time programming, according to the period of the year and to the set latitude, guaranteeing thus a constant
degree of event activation light.
(EXAMPLE: if you set the opening of the roller shutters at 6.00 a.m. in summer, in winter the roller shutter will open for
example at 7.00 a.m. according to the set latitude, thus keeping constant the sun light degree)
When in automatic+holiday mode, the TM XTT 433 R timer
automatically activates the motors according to the set
time, offsetting it by +/- 15 minutes with respect to the set
time. The holiday function lets you simulate the presence
of people in the home.
To set the mode, see the par. “Holiday function setting”
(par. 7.4.2)
Proceed as follows:
To activate holiday mode movement, you must
repeatedly press the key until and are
displayed.
1.
Proceed as follows:
To activate planetary mode movement, you must
repeatedly press the key until and are
displayed.
1.
You can choose on which of the 6 channels you wish to enable this function.
You can choose on which of the 6 channels you wish to enable this function.
IMPORTANT: THE TIMER TAKES MARCH 21 AS REFERENCE DATE TO CALCULATE
THE ACTIVATION TIME

17
ENGLISH
7.3.5 Operation in “automatic + holiday + planetary” mode
When in automatic+holiday+planetary mode, the TM XTT
433 R timer combines holiday and planetary mode. To
set the mode, see the par. “Holiday function setting” and
“Planetary function setting” .
Its operation is based on the programmed activation
set in the TM XTT 433 R timer, which will carry out random
movements offset by +/- 15 minutes, with respect to the
set time, throughout the day and adapting to dawn and
sunset times, calculated by setting the latitude of the
country of installation.
Proceed as follows:
To activate holiday+planetary mode movement,
you must repeatedly press the key until ,
and are displayed..
1.
7.4.1 Setting the automatic function (command setting)
5 Sec.
After having set the correct time (Par. 6.1), proceed as
follows:
1) Press the key for 5 seconds.
Prog will flash.
2) Press the key to confirm
3) Within 5 seconds repeatedly press the key until the
symbol (automatic) is displayed.
4) will flash. Press the key to enter the function
settings.
5) The “ dAY ”window is displayed to choose the days
of the week
SU - Sunday
MO - Monday
TU - Tuesday
WE - Wednesday
TH - Thursday
FR - Friday
SA - Saturday
6) Use the or key to select the days on which you
wish to set the available actions:
every day of the week (SU-MO-TU-WE-TH-FR-
SA);
Saturday and Sunday (SU-SA);
from Monday to Friday (MO-TU-WE-TH-FR);
single day.
7) Press to confirm .
•
•
•
•
7.4 Programming the functions
If you are in the programming menu ( on) and no key is pressed for 1 minute, the
TM XTT 433 R timer will go back to being automatically ready for operation.

18
0
00
S
ENGLISH
11) Use the or key to select the desired daily event
(1-5) .
OFF 1 = event 1 - OFF 2 = event 2 -OFF 3 = event 3
- OFF 4 = event 4 - OFF 5 = event 5
12) Press the key to enable (On) or disable (OFF) the
corresponding event and confirm by pressing .
13) The time at which the previously selected event will
be performed will be displayed.
14) Use the or key to set the command trigger
time and confirm by pressing .
15) The minutes of the previously selected hour will be
displayed. Press to confirm.
16) The movement you wish to perform will be
displayed.
17) Use the or key to set the movement that
you want the roller shutter to perform and confirm by
pressing ;
move up;
preferred position;
move down.
18) The word “donE”” is displayed to confirm that
programming has been completed.
19) To add other events, repeat the procedure starting
from point 9 If you wish to select another channel in
order to set events on it, select exit (see page 19).
20) To exit the programming menu wait 60 seconds or
press for 5 seconds
8) “ Ch ” is displayed to let you choose the channels
on which you can set the actions for the previously
selected days
9) Use the or key to select the desired channel
on which you wish to activate the event and confirm by
pressing .
10) A window will be displayed to let you manage the
daily events. e.g OFF 1
Events are factory set on OFF.
ON / OFF lets you program a certain event and enable/disable it at any time, without having to
delete and re-program the TM XTT 433 R timer.
After having programmed the TM XTT 433 R timer, the settings made will be operative only when
the event is enabled (ON); if the event is disabled (OFF) the settings will not be active but will however remain
memorised in the corresponding setting.

19
ENGLISH
From all the menus, you can go back to the previous one by selecting Exit. To exit and return to the user menu, wait 60 seconds or press the key for 5 seconds
SELECT
DAY SELECT GROUP
(Ch 1-6 or all 6)
SELECT
EVENT (1-5)
SELECT
TIME
SELECT
FUNCTION
CONFIRMATION
MESSAGE
S
Event number
Day in which the event is enabled
Day in which the event is enabled
TO MODIFY
TO CONFIRM
You can go back to the previous function by
selecting exit and confirming with
You can go back to the previous function by
selecting exit and confirming with
You can go back to the
previous menu by selecting
exit and confirming with

20
ENGLISH
7.4.2 Setting “Holiday” and .
The holiday function lets you simulate the presence of people in the home, by automatically activating movement of
the roller shutters. Its operation is based on the programmed activation set in the TM XTT 433 R timer, which will perform
random actions offset by +/- 15 minutes, with respect to the set time throughout the day.
Proceed as follows:
Press the key for 5 seconds.
Prog will flash.
1.
Press the key and then repeatedly press the
key until the holiday function symbol is
displayed.
will flash.
Press the key to select the channel on which
you wish to enable the function.
2.
3.
5 Sec.
Use the or key to select the desired channel
and confirm by pressing .
You can individually select channels 1 to 6 or all of
them simultaneously.
Ch 1 = channel 1 - Ch 2 = channel 2 -
Ch 3 = channel 3 - Ch 4 = channel 4 -
Ch 5 = channel 5 - Ch 6 = channel 6
Ch 1-6 = all channels
4.
Use the or key to enable (ON) or disable (OFF)
the function and confirm by pressing .
5.
Repeat the operations described to set all the
channels and once programming has been com-
pleted, repeatedly press the or key until Exit is
displayed.
Exit will flash.
Press the key to exit the holiday function settings.
6.
7.