Faber STILO Owner's manual

STIL24SSV2
STIL30SSV2
STIL36SSV2
STIL48SSV2
Installation Instructions
Use and Care Information
Instructions d'installation
Utilisez et d'entretien
Instrucciones de instalación
Información de uso y cuidado
STILO

2
CONTENTS
Section Page
IMPORTANT SAFETY INSTRUCTIONS 3
RANGE HOOD DIMENSIONS 6
INSTALLATION HEIGHT REQUIREMENTS 7
PARTS 8
TOOLS NEEDED 10
VENTING METHOD 11
INSTALLING 12
CHOOSING VENTING METHOD 17
ATTACH VENTING: DUCTING 18
ATTACH VENTING: NON DUCTED RECIRCULATING 22
CONNECTING HOUSE POWER 26
OPERATING THE CONTROLS 27
CLEANING STAINLESS STEEL 28
CARING FOR FILTERS 28
REPLACING BULBS 29
WIRING DIAGRAM 30
WARRANTY 31

3
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START
INSTALLING THIS Range Hood
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils slowly on low or medium setting.
b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or
lter.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnoffthe
burner.BECAREFULTOPREVENTBURNS.Iftheamesdonotgooutimmediately
EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will
result.
d) Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate
it.
2. Thereissmallandcontainedintheareawhereitstarted.
3. Theredepartmentisbeingcalled.
4. Youcanghttherewithyourbacktoanexit.
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with
any solid-state speed control device.
WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,
OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have any questions,
contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explo-
sive Materials and Vapors.
WARNING-TOREDUCETHERISKOFFIRE,ELECTRICALSHOCK,ORINJURYTOPERSONS,
OBSERVE THE FOLLOWING:
1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-
dance With All Applicable Codes And Standards, Including Fire-Rated Construction.
2. Sufcientairisneededforpropercombustionandexhaustingofgasesthroughthe
ue(chimney)offuelburningequipmenttopreventbackdrafting.Followtheheating
equipment manufacturer's guideline and safety standards such as those published by
theNationalFireProtectionAssociation(NFPA),andtheAmericanSocietyforHeating,
RefrigerationandAirConditioningEngineers(ASHRAE),andthelocalcodeauthorities.

4
ALL WALL AND FLOOR OPENINGS WHERE THE Range Hood IS INSTALLED
MUST BE SEALED.
This Range Hood requires at least 24" of clearance between the bottom of the Range
Hood and the cooking surface or countertop. This hood has been approved by UL at this
distance from the cooktop.
Thisminimumclearancemaybe higherdependingonlocalbuilding codes.Forgas cooktops
and combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking
surface or countertop. Consult the cooktop or range installation instructions given by the
manufacturer before making any cutouts.
MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the
Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See
Electrical Requirements"
• Venting system MUST terminate outside the home.
• DO NOT terminate the ductwork in an attic or other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOT obstruct the ow of combustion and ventilation air.
• Failure to follow venting requirements may result in a re.
WARNING
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either
through the wall or the roof.
The length of the ductwork and the number of elbows should be kept to a minimum to
provide efcient performance. The size of the ductwork should be uniform. Do not install
two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking
to seal exterior wall or oor opening around the cap.
Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air
turbulence that greatly reduces performance.
Make sure there is proper clearance within the wall or oor for exhaust duct before making
cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut,
then a supporting frame must be constructed.
WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.
CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside
– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces,
or garages.
Cold Weather installations
An additional back draft damper should be installed to minimize backward cold air ow and a nonme-
tallic thermal break should be installed to minimize conduction of outside temperatures as part of the
vent system. The damper should be on the cold air side of the thermal break. The break should be as
close as possible to where the vent system enters the heated portion of the house.
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
4. Ducted fans must always be vented to the outdoors.

5
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit.
A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local
codes in accordance with the electrical rating of this unit as specied on the serial/rating
plate located inside the unit near the eld wiring compartment.
• Electrical ground is required on this Range Hood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other
materials, DO NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral
or grounding circuit could result in electrical shock.
• Check with a qualied electrician if you are in doubt as to whether the Range
Hood is properly grounded.
• Failure to follow electrical requirements may result in a re.
WARNING
!
StateofCaliforniaProposition65Warning(USonly)
WARNING
This product contains chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov

6
RANGE HOOD DIMENSIONS
DRAFT 27-APR-2021 11:38
24" 30" 36" 48"

7
INSTALLATION HEIGHT REQUIREMENTS
MIN. 24" OVER ELECTRIC
MIN. 30" OVER GAS
Min. 24" Min. 30"

8
PARTS
REF. PART QTY
AHood body 1
BTelescopic Lower Chimney 1
CTelescopic Upper Chimney 1
DChimney Brackets 2
EDamper Flaps 2
FHood wall Brackets 1
REF PART
GPozi Screws 3/16" x 1 3/4" 6
HPozi Screws (1/8" x 3/16") 2
ITorx Screws 1/8" x 7/16" 4
LTorx Screws (1/4" x 2 3/4") 2
PARTS INCLUDED

9
B
A
F
C
D
E

10
PARTS NEEDED
PARTS(cont.)
PART
6" Round Metal Ductwork
Drywall plugs or other suitable wall fasteners based on your
installation.
Foil tape
TOOLS NEEDED
TOOL
Tape Measure
Pencil
Electric Drill with 5/16" Drill Bit
Phillips Screwdriver
Torx Screwdriver
Metal sheers
Work gloves
ACCESSORIES AVAILABLE
ACCESSORY SKU#
Replacement Activated Charcoal Filter #FILTER2
Wireless Remote Control #REMCTRL
Direct Connect Wiring Box # WIREBOX
High Ceiling Chimney Kit - Upper and Lower Chimney Flue to
replace the original ue's to t up to 11' ceilings # HIGH3
Ductless Kit - Includes Ductless Diverter, Charcoal Filters # DUCT4

11
VENTING METHOD
Option 1: REAR OR TOP VENTED
Ducted Venting Installation
Option 2: RECIRCULATING
Non ducted - recirculation
1
Requires purchase of
Activated Charcoal
Accessory kit.
Horizontal
Vertical
6 "

12
INSTALLING
DRAW CENTER LINES
Draw a vertical line Xon the supporting wall to the ceiling or
upper limit, at the center of the area in which the hood will be
installed.
Draw a horizontal line Ywhere the bottom edge of the hood will
be located, a minimum of 24" above an electric cooking surface
and 30" above a gas cooking surface.
2
MIN. 24" OVER ELECTRIC/MIN. 30" OVER GAS
Y
X
Y

13
1. Place a bracket D on the wall as shown about 1/8" from the
ceiling or upper limit, aligning the center (notch) with the
vertical reference line Xand mark the wall at the centers of the
holes in the bracket.
2. Place the second bracket Don the wall as shown, below the
rst bracket, at the height of the upper chimney section C
supplied and aligning the center (notch) with the vertical line.
3. Mark the wall at the centers of the holes in the bracket and mark
the point 1 and 2 for the Hood Body installation as shown(12
5/8" from the horizontal line and 4 9/16" from the vertical line).
4. Drill ø 5/16" holes at all the center points marked (point
1,2,3,4,5,6) as shown.
3
C



x6



x6
´
´
´
!
´
´ ´
´



D

14
4
5
I = 6x
I = 6x
2X
Installation screws provided must be secured with wall plugs (purchase
separately).
Insert the two screws Gsupplied with the hood into the Wall Bracket F
as shown and do not tighten all the way to wall leaving 3/16" of the screw
heads exposed.
F
G
Phillips Screwdriver

15
I = 6x
6
7
Use a level to insure that Wall Bracket Fis level and then fully secure the
two screws.
Hook the hood body onto the hood wall bracket F.
F
A
F

16
8Tighten the 2 screws Has shown.
H
Phillips Screwdriver

17
CHOOSING VENTING METHOD
VENTED
RECIRCULATING
Go to Pg.18
Go to Pg.22

18
1
InstallRooforWallCappurchasedseparately.Connectthe6"metal ductwork
to the Roof or Wall Cap and then attach ductwork. Seal with foil tape.
Install the Damper aps Ethat are included with hood by snapping the tabs
into place inside the top of the hood before connecting ductwork.
ATTACH VENTING: DUCTED
E
2

19
3Install the 2 Chimney brackets Dto the middle and upper holes and secure
with screws Gas shown.
L = 4x
G
D
D
Phillips Screwdriver

20
4
5Secure the sides to the brackets by using the 4 screws I.
Slightly widen the two sides of the upper chimney Cand hook them
behind the brackets D, making sure that they are well seated.
N = 4x
D
C
C
I
Torx Screwdriver
D