Faber Cylindra Isola Gloss User manual

Instructions Manual
Руководство по эксплуатации
Naudojimosi instrukcija
Instrukcijas Grāmata
Kasutusjuhend
Manual de instrucciones
ﺐﻴآﺮﺘﻟا ﻞﻴﻟ
د

2
2
INDEX
RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 4
CHARACTERISTICS ............................................................................................................................................................. 7
INSTALLATION...................................................................................................................................................................... 9
USE ...................................................................................................................................................................................... 13
MAINTENANCE................................................................................................................................................................... 14
УКАЗАТЕЛЬ
СОВЕТЫ ИРЕКОМЕНДАЦИИ .......................................................................................................................................... 17
ХАРАКТЕРИСТИКИ............................................................................................................................................................ 20
УСТАНОВКА........................................................................................................................................................................ 22
ЭКСПЛУАТАЦИЯ................................................................................................................................................................ 26
УХОД.................................................................................................................................................................................... 27
TURINYS
PATARIMAI IR NUORODOS............................................................................................................................................... 30
PRIETAISO APRAŠYMAS .................................................................................................................................................. 33
MONTAVIMAS ..................................................................................................................................................................... 35
NAUDOJIMAS...................................................................................................................................................................... 39
VALYMAS IR PRIEŽIŪRA ................................................................................................................................................... 40
INDEKSS
IETEIKUMI UN PRIEKŠLIKUMI........................................................................................................................................... 43
TEHNISKIE DATI................................................................................................................................................................. 46
UZSTĀDĪŠANA.................................................................................................................................................................... 48
IZMANTOŠANA ................................................................................................................................................................... 52
APKOPE............................................................................................................................................................................... 53
INDEKS
SOOVITUSED JA ETTEPANEKUD..................................................................................................................................... 56
OMADUSED......................................................................................................................................................................... 59
PAIGALDAMINE .................................................................................................................................................................. 61
KASUTAMINE...................................................................................................................................................................... 65
HOOLDUS............................................................................................................................................................................ 66
ÍNDICE
CONSEJOS Y SUGERENCIAS........................................................................................................................................... 69
CARACTERÍSTICAS ........................................................................................................................................................... 72
INSTALACIÓN ..................................................................................................................................................................... 74
USO...................................................................................................................................................................................... 78
MANTENIMIENTO............................................................................................................................................................... 79
EN
RU
LT
LV
EE
ES
SA

3
3
سﺮﻬﻔﻟا
تﺎﺣاﺮﺘﻗا وتادﺎﺷرا..............................................................................................................................................82
ﺺﺋﺎﺼﺨﻟا...........................................................................................................................................................85
ﺐﻴآﺮﺘﻟا.............................................................................................................................................................87
ماﺪﺨﺘﺳﻻا.............................................................................................................................................................91
ﺔﻧﺎﻴﺼﻟا ﺔﻴﻠﻤﻋ....................................................................................................................................................92

EN 4
4
RECOMMENDATIONS AND SUGGESTIONS
The Instructions for Use apply to several versions of this appliance.
Accordingly, you may find descriptions of individual features that do not
apply to your specific appliance.
INSTALLATION
• The manufacturer will not be held liable for any damages resulting from
incorrect or improper installation.
• The minimum safety distance between the cooker top
and the extractor hood is 650 mm (some models can
be installed at a lower height, please refer to the
paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that
indicated on the rating plate fixed to the inside of the
hood.
• For Class I appliances, check that the domestic
power supply guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum
diameter 120 mm. The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-
electrical appliances (e.g. gas burning
appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the
backflow of exhaust gas. The kitchen must have
an opening communicating directly with the open
air in order to guarantee the entry of clean air.
When the cooker hood is used in conjunction with
appliances supplied with energy other than electric, the negative pressure in
the room must not exceed 0,04 mbar to prevent fumes being drawn back
into the room by the cooker hood.
• In the event of damage to the power cable, it must be replaced by the
manufacturer or by the technical service department, in order to prevent any
risks.
2°

EN 5
5
• If the instructions for installation for the gas hob specify a greater distance
specified above, this has to be taken into account. Regulations concerning
the discharge of air have to be fulfilled.
• Use only screws and small parts in support of the hood.
Warning: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical hazards.
• Connect the hood to the mains through a two-pole switch having a contact
gap of at least 3 mm.
USE
• The extractor hood has been designed exclusively for domestic use to
eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making
sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored
during use: overheated oil can burst into flames.
• Do not flambè under the range hood; risk of fire.
• This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

EN 6
6
• “CAUTION: Accessible parts may become hot when used with cooking
appliances.”
MAINTENANCE
•Switch off or unplug the appliance from the mains supply before carrying out
any maintenance work.
• Clean and/or replace the Filters after the specified time period (Fire hazard).
• The Grease filters must be cleaned every 2 months of operation, or more
frequently for particularly heavy usage, and can be washed in a dishwasher.
• The Activated charcoal filter is not washable and cannot be regenerated,
and must be replaced approximately every 4 months of operation, or more
frequently for particularly heavy usage.
• "Failure to carry out cleaning as indicated will result in a fire hazard".
• Clean the hood using a damp cloth and a neutral liquid detergent.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.

EN 7
7
CHARACTERISTICS
Components
Ref. Q.ty Product Components
11 Hood Body, complete with: Controls, Light, Blower, Filters
21 Chimney Upper
7.1 1 Telescopic frame complete with extractor, consisting of:
7.1a 1 Upper frame
7.1b 1 Lower frame
91 Reducer Flange ø 150-120 mm
10 1 Flange ø 120 mm
10a 1 Damper (Optional)
15 1 Recirculation Air Outlet Connection
25 2 Pipe clamps
Ref. Q.ty Installation Components
11 4 Wall Plugs ø 10
12c 4 Screws 2,9 x 6,5
12f 4 Screws M6 x 10
12g 4 Screws M6 x 80
12h 4 Screws 5,2 x 70
21 1 Drilling template
22 4 6.4 mm int. dia washers
23 4 M6 nuts
Q.ty Documentation
1 Instruction Manual
2
11
12h
22
23
21
7.1
1
12g
9
25
7.1a
7.1b
15
12f
10
12c
10a

EN 8
8
Dimensions
* **
Min.
550mm
Min.
550mm
* Dimensions of the hood in ducting version.
** Dimensions of the hood in recycling version.

EN 9
9
INSTALLATION
Drilling the Ceiling/shelf and fixing the frame
DRILLING THE CEILING/SHELF
• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.
• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the
template is in the correct position by lining up the axes of the template with those of the hob.
• Mark the centres of the holes in the template.
• Drill the holes at the points marked:
• For concrete ceilings, drill for plugs appropriate to the screw size.
• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert
the Dowels 11 supplied).
• For wooden beam ceilings, drill according to the wood screws used.
• For wooden shelf, drill ø 7 mm.
• For the power supply cable feed, drill ø 10 mm.
• For the air outlet (Ducted Version), drill according to the diameter of the external air ex-
haust duct connection.
• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:
• For concrete ceilings, use the appropriate plugs for the screw size (not provided).
• for Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h,
supplied.
• For wooden beam ceilings, use 4 wood screws (not provided).
• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

EN 1
10
PREPARATION OF THE FRAME FOR THE HOOD IN RE-
CYCLING VERSION
In case the hood is used in recycling version it is neces-
sary to prepare the frame with all the necessary connec-
tion pieces. In order to make the installation easier it is
necessary to lengthen the frame:
• Unscrew the two screws 2.1 fixing the upper chim-
ney to the frame and pull the chimney out.
• Unscrew the four safety screws placed at the top in
the frame separation area. (A).
• Unscrew the eight metric screws connecting the two
columns, placed on both sides of the frame (B).
Installation of components in recycling version:
• Fix the recycling air outlet piece 15 to the upper part
of the frame using four 12c screws supplied with the
hood.
• Fix the flange (ø120) 10 to the lower part of the recy-
cling air outlet 15.
• Put the reducer flange 9on the hood body outlet.
• At this point, join the flanges with a pipe. In order to
calculate the height of the pipe it is necessary to es-
timate the height of the hood (mm) and subtract 615
mm. (H pipe = H hood-615).
• Lengthen the frame so that the pipe can be inserted.
Place the pipe between the two flanges and block it.
Make sure that the height of the frame is correct con-
sidering the height of the cooker hood (H frame = H
hood – 184). Adjust the height of the frame and
tighten again the earlier removed screws. Tighten
again the safety screws in order to give more stability
to the structure.
• Fix the pipe with the pipe clamps 25 supplied with
the hood.
A
B
15
12c
10

EN 1
11
FIXING THE FRAME
• Lift the frame up, making sure that the index over the frame
plate is turned forwards.
• Fit the frame slots onto the two screws inserted in the ceiling as
above, and turn until reaching the centre of the adjustment slot.
• Tighten the two screws and fasten the other two screws pro-
vided; before locking the screws completely, it is possible to
adjust the frame by turning it, making sure that the screws do
not come out of their housing in the adjustment slot.
• The Frame must be securely fastened so as to support both the
weight of the Hood and the stress caused by occasional axial
pressure against the fitted Appliance. After fixing, make sure
that the base is stable even when the Frame is subjected to lat-
eral stress.
• If the Ceiling is not strong enough in the area where the hood
is to be fixed, the Installer must strengthen the area using suit-
able plates and counterplates anchored to resistant structures.
2
112
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the
chimney using either a flexible or rigid pipe ø 150 or 120mm, the
choice of which is left to the installer.
To install a ø 150
• To install the dumper 10a.
• Fix the pipe in position using sufficient pipe clamps (not sup-
plied).
To install a ø 120
• To install a ø 120 mm air exhaust connection, insert the re-
ducer flange 9on the dumper 10a.
• Fix the pipe in position using sufficient pipe clamps (not sup-
plied).
• Remove any activated charcoal filters.
9
ø 120
ø 150
10a
10a

EN 1
12
Installing of the chimney and fixing of the hood
When the hood is installed in recycling version the chimney has
to be positioned with the slots upwards. When the hood is in-
stalled in ducting version it has to be positioned in the opposite
way.
• Place the chimney on the frame and fix it to the upper part of it
with the earlier removed screws. When installing the hood in
recycling version make sure that the slots correspond to the air
outlet of the recycling air outlet piece 15.
• Open the lighting unit by slightly pulling the notch. Remove
the unit from the hood by sliding the fixing pivot.
• Remove the filter pushing it towards the back side of the hood
unit and simultaneously pulling downwards.
• Remove possible charcoal filters.
• In order to fix the hood body to the frame insert the 4 screws
12f in their seats. It is necessary to leave at least 4-5 mm gap
between the screw heads and the frame plate.
• Hook the hood canopy to the frame and turn it to the left until
it reaches the stop, then lock the screws immediately to prevent
the hood canopy from falling out accidentally.
2
1
ELECTRICAL CONNECTION
• Connect the Hood to the mains power supply, inserting a two-
pole cut-out switch with contact aperture of at least 3 mm
along the line.
• Ensure that the supply cable connector is properly inserted into
the Suction device socket
• Hook up the Commands connector Cmd.
• Hook up the Spotlights connector Lux to the socket provided
behind the lighting unit cover.
• For the Recirculation Version, fit the Activated Charcoal
Odour Filter.
• Replace the filters and the lighting unit.
Cmd
Lux

EN 1
13
L
T1
T2
T3
T4
S1
L
S1
T1 T2 T3 T4
LT3
S1
T2
T1 T4
USE
Control panel
Button Led Function
L- Turns the lights on/off at maximum strength.
T1 Fixed Turns the motor on/off at speed one.
T2 Fixed Turns the Motor on at speed two.
Press and hold the button for approximately 3 seconds, with all the loads turned
off (Motor and Lights), to turn the Activated Charcoal Filter alarm on. The
relevant LED flashes twice to confirm.
To turn the alarm off, press the button again and hold for at least 3 seconds. The
relevant LED flashes once.
T3 Fixed Turns the Motor on at speed three.
Press and hold the button for approximately 3 seconds, with all the loads turned
off (Motor and Lights), to perform a reset of Filter saturation alarm. The LED S1
flashes three times.
T4 Fixed Turns the Motor on at INTENSIVE Speed.
This speed is timed to run for 6 minutes. At the end of this time, the system
returns automatically to the speed that was set before. If it is activated with the
motor turned off, the hood will switch to OFF at the end of the time.
Press and hold for 3 seconds to enable the remote control, indicated by the LED
flashing twice.
Press and hold for 3 seconds to disable the remote control, indicated by the LED
flashing just once.
S1 Fixed Signals the Metal Grease Filter saturation alarm, indicating that it is necessary to
wash the filters. The alarm is triggered after the Hood has been in operation for
100 working hours. (Reset see the parag. Maintenance)
Flashing When this is activated, it signals the Activated Charcoal Filter saturation alarm,
indicating that the filter must be changed; the Metal Grease Filters must also be
washed. The Activated Charcoal Filter saturation alarm comes
into operation after the Hood has been working for 200 hours. (Activation and
Reset see the parag. Maintenance)

EN 1
14
MAINTENANCE
REMOTE CONTROL (OPTIONAL)
The appliance can be controlled using a remote control powered
by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-
AAA type (not included).
• Do not place the remote control near to heat sources.
• Used batteries must be disposed of in the proper manner.
Metal grease filters
These can be washed in the dishwasher, and need to be cleaned
whenever the S1 Led comes on or at least once every 2 months
use, or more frequently if use is particularly intensive.
CLEANING THE FILTERS
Resetting the alarm signal
• Turn the Lights and the Suction Motor off.
• Press T3 and hold for at least 3 seconds, until LED flashes
three times in confirmation.
Cleaning the Filters
• Open the lighting unit by pulling on the nocth.
• Remove the Filter, pushing it towards the back of the unit and
at the same time pulling downward.
• Wash the filter without bending it, and leave it to dry thor-
oughly before replacing (if the surface of the filter changes
colour over time, this will have absolutely no effect on its effi-
ciency).
• Replace, taking care to ensure that the handle faces forwards.
• Replace the lighting unit.

EN 1
15
Activated Charcoal Filter (Recirculation Version)
This cannot be washed or regenerated, and must be changed when led S1 starts to flash, or at
least once every 4 months. The Alarm signal, if it has been activated, only appears when the
Suction motor is turned on.
Activating the alarm signal
• In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installa-
tion or at a later date.
• Turn the Lights and the Suction Motor off.
• Press button T2 and hold it for 5 seconds until the LED flashes twice in confirmation:
CHANGING
Resetting the alarm signal
• Turn the Lights and the Suction Motor off.
• Press T3 and hold for at least 3 seconds, until LED
flashes three times in confirmation.
Changing the Filter
• Open the lighting unit by pulling on the notch provided.
• Remove the Metal Grease Filter
• Remove the saturated Activated charcoal filter, using
the hooks provided.
• Fit the new Filter, hooking it into place.
• Fit the Grease filter and the Light Unit back into place.

EN 1
16
Lighting
LIGHT REPLACEMENT
20 W halogen light.
• Extract the lamp from the lamp holder by pulling
gently.
• Replace with another of the same type, making sure
that the two pins are properly inserted in the lamp
holder socket holes.
Lamp Power (W) Socket Voltage (V) Dimension (mm) ILCOS Code
28 E14 220 – 240 104 x 35 HSGSB/C/UB-28-220/240-E14
20 G4 12 33 x 9 HSG/C/UB-20-12-G4
35 GU10 230 51 x 50,7 HAGS-35-230-GU10-51/40
50 GU10 230 51 x 50,7 HAGS-35-230-GU10-51/20
20 GU4 12 40 x 35 HRGS-20-12-GU4-35/30
20 GU5.3 12 46 x 51 HRGS-20-12-GU5.3-50/10
16 G13 95 720 x 26 FD--16/40/1B-E--G13--26/720
18 G13 57 589,8 x 26 FD--18/40/1B--E--G13--26/600
9 G23
60 (lamp)
220-240 (starter) 167 x 28 FSD-9/27/1B-I-G23
11 G23
91 (lamp)
220-240 (starter) 235,8 x 28 FSD-11/40/1B-I-G23

RU 1
17
СОВЕТЫ ИРЕКОМЕНДАЦИИ
ВИнструкциях по эксплуатации описаны различные модели прибора.
Поэтому вы можете встретить описание некоторых характеристик, не
относящихся кприобретенному вами прибору.
УСТАНОВКА
• Изготовитель не несет ответственность за убытки, возникающие врезультате
неправильной установки или эксплуатации прибора.
• Безопасное расстояние между варочной панелью и
всасывающей вытяжкой должно быть не менее 650
мм (некоторые модели можно устанавливать ниже; см.
раздел, посвященный рабочим размерам иоперациям
по установке прибора).
• Проверьте соответствие напряжения сети указанному
на табличке, закрепленной внутри вытяжки.
• Для приборов класса I проверьте, чтобы вэлектрической сети вашего дома
была предусмотрена соответствующая система заземления.
Соедините вытяжку сдымоходом спомощью трубы минимального диаметра
120 мм. Труба для отведения дыма должна быть как можно короче.
• Не соединяйте всасывающую вытяжку сдымоходами, по которым выводится
дым, образующийся впроцессе горения (например,
отопительные котлы, камины ипроч.).
• Если вытяжной аппарат используется всочетании с
приборами, работающими не от электрического тока
(например, газовые приборы), помещение должно
хорошо проветриваться во избежание обратного
потока отходящих газов. Для притока впомещение
свежего воздуха на кухне должно быть предусмотрено выходящее на улицу
окно.При пользовании кухонной вытяжкой всочетании сприборами,
работающими не от электрического тока, отрицательное давление в
помещении не должно превышать 0,04 мбар стем, чтобы дым не всасывался
вытяжкой обратно впомещение.
• Во избежание опасности вслучае повреждения кабеля питания, он должен
быть заменен изготовителем или специалистами отдела технического
обслуживания.
2°

RU 1
18
• Если винструкциях по установке газовой плиты сказано, что расстояние до
вытяжки должно быть больше указанного выше, следует
придерживаться предписанных размеров. Соблюдайте все
нормативные требования по отведению отработанного воздуха.
• Используйте только винты иметизы, пригодные для установки
вытяжки. Предупреждение: использование винтов изажимных
устройств, не соответствующих указаниям данных инструкций, может
привести квозникновению опасных ситуаций икэлектрическим ударам.
• Соедините вытяжку ссетью питания спомощью двухполюсного
выключателя сминимальным разведением контактов 3 мм.
ЭКСПЛУАТАЦИЯ
• Всасывающая вытяжка предназначена только для применения вбыту
для удаления из кухни запахов от готовки.
• Никогда не пользуйтесь вытяжкой виных целях, отличных от тех, для
которых она предназначена.
• Никогда не оставляйте высокое пламя под вытяжкой, находящейся в
работе.
• Регулируйте силу пламени таким образом, чтобы оно оставалось под
дном емкости для готовки ине вырывалось за его пределы.
• При готовке во фритюрнице постоянно следите
за ее работой: сильно нагретое масло может
воспламениться.
• Не готовьте блюда фламбе под вытяжкой:
опасность возникновения пожара.
• Прибором могут пользоваться дети старше 8
лет илица сограниченными психическими, физическими исенсорными
способностями, атакже не имеющие достаточного опыта изнаний, но
только под присмотром ответственных лиц ипри условии, что они
обучены безопасной эксплуатации прибора изнают освязанных сего
неправильным использованием опасностях. Следите, чтобы дети не
играли сприбором. Очистку иуход за прибором должен обеспечивать
пользователь, такие действия могут выполнять идети, но только под
надзором взрослых.

RU 1
19
• “ ВНИМАНИЕ: доступные части вытяжки могут сильно нагреваться во
время работы газовых приборов.
УХОД
• Перед выполнением любой операции по очистке иуходу выключите
или отсоедините прибор от электрической сети.
• Очищайте и/или заменяйте фильтры по истечении указанного периода
времени (опасность возникновения пожара).
• Жировые фильтры необходимо очищать раз в2 месяца работы или
чаще вслучае очень интенсивного использования прибора; жировые
фильтры можно мыть впосудомоечной машине.
• Фильтр на активированном угле нельзя мыть ивосстанавливать, его
следует менять примерно раз в4 месяца работы или чаще вслучае
очень интенсивного использования прибора.
• "Опасность возникновения пожара, если очистка прибора не
выполняется всоответствии синструкциями".
• Очищайте вытяжку влажной тряпкой, смоченной внейтральном жидком
моющем веществе.
Символ на изделии или на упаковке указывает, что прибор нельзя
выбрасывать, как обычный бытовой мусор. Прибор, подлежащий
уничтожению, необходимо сдать вспециальный сборный пункт для
повторного использования электрических иэлектронных компонентов.
Пользователь, правильно сдающий прибор на переработку, помогает
предотвратить потенциальные негативные последствия для окружающей
среды идля здоровья людей, возникающие вслучае неправильного его
уничтожения. За более подробной информацией овторичном
использовании прибора обращайтесь вгородской совет, вместную
службу по переработке отходов или вмагазин, где прибор был
приобретен.

RU 2
20
ХАРАКТЕРИСТИКИ
Части
Об. Кол. Части изделия
11 Корпус вытяжки вкомплекте сустройствами управления, ос-
вещением, фильтрами, нижней частью дымохода
21 Верхняя часть дымохода
7.1 1 Телескопическая решетчатая конструкция свытяжным устрой-
ством вкомплекте с:
7.1a 1 верхним решетчатым каркасом
7.1b 1 нижним решетчатым каркасом
91 Переходный фланец ø 150-120 мм
10 1 Фланец ø 120 мм
10a 1 Фланец склапаном (необязательный)
15 1 Выпускной штуцер отфильтрованного воздуха
25 Трубных зажима (не включено вкомплект поставки)
Об. Кол. Установочные компоненты
11 4 Вкладыша ø 10
12с4 Винта 2,9 х6,5
12f 4 Винта M6 x 15
12g 4 Винта M6 x 80
12h 4 Винта 5,2 х70
21 1 Калибр сверления
22 4 Шайбы ø 6,4
23 4 Гайки M6
Кол. Документация
1 Руководство по эксплуатации
2
11
12h
22
23
21
7.1
1
12g
9
25
7.1a
7.1b
15
12f
10
12c
10a