Fairland TurboSilence InverX IXCR26 User manual

SUMMARY
1. GENERAL INFORMATION 3
1.1. Contents: 3
1.2. Operating conditions and range: 3
1.3. Advantages o di erent modes: 3
1.4. Kind reminder: 4
2. OPERATIONS 6
2.1. Notice be ore using 6
2.2. Operation instructions 6
2.3. Daily maintenance and winterizing 8
3. TECHNICAL SPECIFICATION 9
1. TRANSPORTATION 10
2. INSTALLATION AND MAINTENANCE 10
2.1. Notice be ore installation： 10
2.2. Installation instruction 11
2.3. Trial a ter installation 14
2.4. Maintenance and winterizing 14
3. TROUBLE SHOOTING FOR COMMON FAULTS 15
4. FAILURE CODE 16
APPENDIX 1: HEATING PRIORITY WIRING DIAGRAM (OPTIONAL) 17
APPENDIX 2: HEATING PRIORITY WIRING DIAGRAM (OPTIONAL) 18
APPENDIX 3: HEATING PRIORITY WIRING DIAGRAM (OPTIONAL) 19
5. WIFI SETTING 21
PLEASE READ IT CAREFULLY AND KEEP IT FOR SUBSEQUENT USE
This manual provides you necessary in ormation or optimal use and maintenance
For users .
P.1
-
P.
9
For installers and professi
onals

P.
10
-
P.
26

Warning
：
a.
Please read the following tips before installation, use and maintenance.
b.
Installation, removal and maintenance must be carried out by Professional
accordance with the instructions.
c.
Gas leakage test must be done before and after installation.
1. Use
a.
It must be installed or removed by professionals, and it is forbid
permission.
b.
Don’t put obstacles before the air inlet and outlet of the heat pump.
2. Installation
a.
This product must be kept away from any source of fire.
b.
The installation can’t be in a closed environment or indoors,
c.
Vacuum completely before welding, field welding is not allowed, welding can only be performed by
professional personnel in professional maintenance center.
1
：
Please read the following tips before installation, use and maintenance.
Installation, removal and maintenance must be carried out by Professional
accordance with the instructions.
Gas leakage test must be done before and after installation.
It must be installed or removed by professionals, and it is forbid
den to dismantle and refit without
Don’t put obstacles before the air inlet and outlet of the heat pump.
This product must be kept away from any source of fire.
The installation can’t be in a closed environment or indoors,
and must be kept well ventilated.
Vacuum completely before welding, field welding is not allowed, welding can only be performed by
professional personnel in professional maintenance center.
Installation, removal and maintenance must be carried out by Professional
personnel in
den to dismantle and refit without
and must be kept well ventilated.
Vacuum completely before welding, field welding is not allowed, welding can only be performed by

d.
Installation must be stopped if any gas leakage,
maintenance center.
3. Transportation & Storage
a.
ealing is not allowed during transportation
b.
Transporting goods at a constant speed is needed to avoid sudden acceleration or sudden braking,
so as to reduce the co
llision of goods.
c.
The unit must be far away from any source of fire.
d.
torage place must be bright, wide, open and good ventilation, ventilation equipment is required.
. Maintenance Notice
a.
If maintenance or scrap is required, contact an authorized service
b. Qualification requirement
All operators who dispose gas
must be qualified by valid certification which issued by professional
agency.
c.
Please strictly comply with the requirement from manufacturer wh
Please r
efer to the technical service manual.
2
Installation must be stopped if any gas leakage,
and the
unit must be returned to
ealing is not allowed during transportation
Transporting goods at a constant speed is needed to avoid sudden acceleration or sudden braking,
llision of goods.
The unit must be far away from any source of fire.
torage place must be bright, wide, open and good ventilation, ventilation equipment is required.
If maintenance or scrap is required, contact an authorized service
center nearby
must be qualified by valid certification which issued by professional
Please strictly comply with the requirement from manufacturer wh
en maintenance or filling gas.
efer to the technical service manual.
unit must be returned to
professional
Transporting goods at a constant speed is needed to avoid sudden acceleration or sudden braking,
torage place must be bright, wide, open and good ventilation, ventilation equipment is required.
center nearby
must be qualified by valid certification which issued by professional
en maintenance or filling gas.

FOR USER
1. GENERAL INFORMATI
1.1. Contents:
A ter unpacking, please check i you have all the ollowing components.
1.2. Ope ating conditions and
ITEMS
Ope ating ange
Temp. setting
The heat pump will have i ℃
1.3. Advantages of diffe ent modes:
The heat pump has three modes:
Booster,
conditions.
MODE
Booster mode
Smart mode
Silence mode
3
1. GENERAL INFORMATI
ON
A ter unpacking, please check i you have all the ollowing components.
1.2. Ope ating conditions and
ange:
ITEMS
RANGE
Air temp
-15℃
～
heating
18℃
～
Cooling
12℃
～
ideal pe fo mance in the ope ation ange ℃
1.3. Advantages of diffe ent modes:
Booster,
Smart and Silence. They have di erent advantages under di erent
ADVANTAGES
Heating capacity: 120%
Fast heating
Heating capacity:100%~20%
Intelligent optimization according to ambient
water temperature
Energy e iciently saving
Heating capacity: 80%~20%
Use at night
RANGE
～
43℃
～
40℃
～
30℃
e Ai 15℃
～25℃.
Smart and Silence. They have di erent advantages under di erent
temperature and

FOR USER
1.4. Kind eminde :
This heat pump has Powe -
off memo y function. When the powe is ecove ed, the heat pump
will esta t automatically.
1.4.1. The heat pump can only be used to heat the pool water.
lammable or turbid liquid.
1.4.2. Don’t li t the water union when moving the heat pump since the titanium heat exchanger
inside the heat pump will be damaged.
1.4.3. Don’t put obstacles be ore the air inlet and outlet o the heat pump.
1.4.4. Don’t put anything into inlet or
even stopped.
1.4.5. Don’t use or store combustible gas or liquid such as thinners, paint and uel to avoid ire.
4
off memo y function. When the powe is ecove ed, the heat pump
1.4.1. The heat pump can only be used to heat the pool water.
It can NEVER
1.4.2. Don’t li t the water union when moving the heat pump since the titanium heat exchanger
inside the heat pump will be damaged.
1.4.3. Don’t put obstacles be ore the air inlet and outlet o the heat pump.
1.4.4. Don’t put anything into inlet or
outlet, or the e iciency o the heat pump will be reduced or
1.4.5. Don’t use or store combustible gas or liquid such as thinners, paint and uel to avoid ire.
off memo y function. When the powe is ecove ed, the heat pump
It can NEVER
be used to heat other
1.4.2. Don’t li t the water union when moving the heat pump since the titanium heat exchanger
outlet, or the e iciency o the heat pump will be reduced or
1.4.5. Don’t use or store combustible gas or liquid such as thinners, paint and uel to avoid ire.

FOR USER
1.4.6. I any abnormal circumstances occurred,
leakage of elect icity, switch off the main powe immediately and contact you
local deale .
Don’t try to repair the heat pump by yourselves.
1.4.7. The main power switch should be out o the reach o Children.
1.4.8. Please cut o the power in the lightning storm weather.
1.4.9. Please note that ollowing codes are not ailure.
No wate flow
Anti-
F eezing Reminde
Out of the ope ating ange
Insufficient wate flow o pump blocked
Powe abno mal
5
1.4.6. I any abnormal circumstances occurred,
e.g.: abno mal noises, smel
leakage of elect icity, switch off the main powe immediately and contact you
Don’t try to repair the heat pump by yourselves.
1.4.7. The main power switch should be out o the reach o Children.
1.4.8. Please cut o the power in the lightning storm weather.
1.4.9. Please note that ollowing codes are not ailure.
CODES
F eezing Reminde
Out of the ope ating ange
Insufficient wate flow o pump blocked
e.g.: abno mal noises, smel
ls, smokes and
leakage of elect icity, switch off the main powe immediately and contact you
CODES

FOR USER
2.1. Notice befo e using
2.1.1.
For longer service li e, please ensure water pump is on be ore heat pump
water pump is o a ter heat pump is o .
2.1.2.
Ensure no water leakage on piping system, then unlock screen and press
heat pump.
2.2. Ope ation inst uctions
SYMBOL
DESIGNATION
ON/OFF
Unlock
Speed
Up / Down
Note: (Button
will be light all the time
① Screen lock:
a.
I no operation in 30 seconds, screen will be locked.
b.
When HP is o , screen will be dark and “0%” will be displayed.
c. Press
or 3 seconds to lock screen and it will be dark
6
2. OPERATIONS
For longer service li e, please ensure water pump is on be ore heat pump
water pump is o a ter heat pump is o .
Ensure no water leakage on piping system, then unlock screen and press
2.2. Ope ation inst uctions
DESIGNATION
FUNCTION
ON/OFF
1. Power On/O
2. Wi i setting
Unlock
1. Press it for 3 seconds to
unlock/lock
2. After
screen is unlocked, press it to select mode
Auto (12~40℃)Heating (18~40
℃
Speed
Select Booster/Smart/Silence mode
Up / Down
Adjust set temperature
will be light all the time
when power is on.):
I no operation in 30 seconds, screen will be locked.
When HP is o , screen will be dark and “0%” will be displayed.
or 3 seconds to lock screen and it will be dark
For longer service li e, please ensure water pump is on be ore heat pump
starts to work, and
Ensure no water leakage on piping system, then unlock screen and press
to power on
unlock/lock
screen
screen is unlocked, press it to select mode
.
℃
)Cooling (12~30℃)

FOR USER
② Screen unlock:
a. Press
or 3 seconds to unlock sc
b.
Only a ter screen is unlocked, any other buttons can be unctioned.
1.Power On: Press
or 3 seconds to light up screen, then press
2.
Adjust Set Temperature: When screen is unlocked, press
3. Mode Selection: Press
to select mode.
Auto : ad
justable temperature range 12~40
Heating : ad
justable temperature range 18~40
Cooling : adjustable temperature range 12~30
4.
Booster/Smart/Silence mode selection:
① Smart mode as de ault will be activ
ated when he
② Press
to enter Booster mode, and screen shows
Water inlet
temperature
Water outlet
temperature
7
or 3 seconds to unlock sc
reen and it will be lit up.
Only a ter screen is unlocked, any other buttons can be unctioned.
Heating
Cooling
Auto
Heating capacity percentage
Wifi connection
Water inlet
Water outlet
or 3 seconds to light up screen, then press
to power on heat pump.
Adjust Set Temperature: When screen is unlocked, press
or
to display or adjust the set temperature.
to select mode.
justable temperature range 12~40
℃
justable temperature range 18~40
℃
Cooling : adjustable temperature range 12~30
℃
Booster/Smart/Silence mode selection:
ated when he
at pump is on, and screen shows
to enter Booster mode, and screen shows
, then press
to enter Silence mode, the screen
to power on heat pump.
to display or adjust the set temperature.
.
to enter Silence mode, the screen
Booster/ mart/ ilence
mode

FOR USER
shows . Press
again, the screen shows
Attention:
a. When use the booster mode,
you should select it every time, the machine will not automatically enter the booster
mode.
b. During the booster mode, when the machine reaches the set temperature, it will automatically return to the
smart mode.
5. De rosting
a. Auto De rosting: When h
eat pump is de rosting,
b. Compulsory De rosting: When heat pump is heating, press
compulsory de rosting, and
will be lashing. A ter de rosting,
(Note: Compulsory de rosting intervals should be more than 30 minutes and the compressor should run or
more than 10 minutes.)
6. Wi i setting
Please kindly check the last page.
2.3. Daily maintenance and winte izing
2.3.1. Daily Maintenance
Please don’t fo get to cut off powe su

Please clean the evaporator with household detergents or clean water, NEVER use gasoline,
thinners or any similar uel.
 Check
bolts, cables and connections regularly
2.3.2. Winte izing
In winter season when you don’t swim, please cut o power supply and drain water out o the
heat pump.
When using the h ℃
8
again, the screen shows
and return to Smart mode.
you should select it every time, the machine will not automatically enter the booster
b. During the booster mode, when the machine reaches the set temperature, it will automatically return to the
eat pump is de rosting,
will be lashing. A ter de rosting,
b. Compulsory De rosting: When heat pump is heating, press
and
together or 5 seconds to start
will be lashing. A ter de rosting,
will s
top lashing.
(Note: Compulsory de rosting intervals should be more than 30 minutes and the compressor should run or
2.3. Daily maintenance and winte izing
Please don’t fo get to cut off powe su
pply of the heat pump
Please clean the evaporator with household detergents or clean water, NEVER use gasoline,
bolts, cables and connections regularly
.
In winter season when you don’t swim, please cut o power supply and drain water out o the
heat pump under 2 , make sure there is ℃
Impo tant:
Unscrew the water union o inlet
to let the water low out.
When the water in machine reezes in
winter season, the titanium heat
exchanger may be damaged.
you should select it every time, the machine will not automatically enter the booster
b. During the booster mode, when the machine reaches the set temperature, it will automatically return to the
will be lashing. A ter de rosting,
will stop lashing.
together or 5 seconds to start
top lashing.
(Note: Compulsory de rosting intervals should be more than 30 minutes and the compressor should run or
Please clean the evaporator with household detergents or clean water, NEVER use gasoline,
In winter season when you don’t swim, please cut o power supply and drain water out o the
always water low.℃
Unscrew the water union o inlet
pipe
When the water in machine reezes in
winter season, the titanium heat

FOR USER
3.
TECHNICAL SPECIFICAT
Model IXCR26
IXCR
Advised pool volume (m
3
)
20~40 2
5
Wo king ai temp ( )
℃
Pe fo mance Condition: Ai 26°C, Wate 26°C, Humidity 80%
Heating capacity (kW)
in mart mode
8.5
11.0
Heating capacity (kW)
in Booster mode 10.2
13.0
C.O.P in mart mode 8.0
8.5
C.O.P 15.6~7.3
1
5.5
C.O.P at 50% speed 11.8
12.0
Pe fo mance Condition: Ai 15°C, Wate 26°C, Humidity 70%
Heating capacity (kW)
in mart mode
6.0
7.5
Heating capacity (kW)
in Booster mode 7.0
9.0
C.O.P in mart mode 5.4
5.5
C.O.P 7.1~4.9 7.
0
C.O.P at 50% speed 6.7
6.
Pe fo mance Condition: Ai 35°C, Wate 28
°C, Humidity
Cooling capacity (kW) 4.5
5.8
Sound pressure at 1m dB(A)
38.5~ 5.5
38.6~ 6.9
Sound pressure o 50%
capacity at 1m dB(A) 39.5
41.3
Sound pressure at 10m dB(A)
18.5~25.5
18.6~26.9
Power supply
Rated input power(kW) at air
15°C 0.18~1.43
0.2
2
Rated input current(A) at air
15°C 0.78~6.2
0.96
~6.
Advised water lux (m³/h) 2~4
3~4
Water pipe in-out Spec
(mm)
Net Dimension Lx WxH
(mm)
893×432×
650
893
×
6
Net Weight (kg) 59
61

The values indicated are valid under ideal conditions: Pool cov
running at least 15 hours a day.
 Related parameters
are subject to adjustment periodically or technical improvement without urther notice. For
details please re er to nameplate.
9
TECHNICAL SPECIFICAT
ION
IXCR
36 IXCR 6 IXCR56 IXCR66
IXCR
5
~45 30~55 40~75 50~95
65
-15~43
Pe fo mance Condition: Ai 26°C, Wate 26°C, Humidity 80%
11.0
14.0 18.0 22.0
13.0
17.0 21.5 26.0
8.5
7.7 7.5 8.0
5.5
~7.5 16.0~6.6 15.5~6.5 16.5~7.0 1
6.3
12.0
11.5 11.5 11.6
Pe fo mance Condition: Ai 15°C, Wate 26°C, Humidity 70%
7.5
9.5 12.0 15.0
9.0
11.5 14.5 18.0
5.5
5.2 5.2 5.6
0
~5.0 7.5~4.5 8.0~4.7 8.0~5.1
8.0
6.
7 6.8 7.0 7.0
°C, Humidity
80%
5.8
6.7 8.2 12.0
38.6~ 6.9
2.0~ 7.7 2.9~50.8 0.8~51.2
3.3
41.3
43.7 44.5 44.4
46.4
18.6~26.9
22.0~27.7 22.9~30.8 20.8~31.2
23.3
230V/1 Ph/50Hz
2
~1.8 0.26~2.56 0.31~3.08 0.38~3.53 0.
46
~6.
7.82 1.14~11.3 1.35~13.4 1.65~15.3 2.
01
3~4
4~6 6.5~8.5 8~10
10
50
×
432×
6
50
939×432×
650
995×432×
750
1125×429×
952
10
74
61
63 70 90
The values indicated are valid under ideal conditions: Pool cov
ered with an isothermal cover, iltrati
are subject to adjustment periodically or technical improvement without urther notice. For
IXCR
80 IXCR80T
IXCR110T
65
~120 65~120 90~160
27.5
27.5 33.0
32.0
32.0 40.0
7.6 7.6 7.5
6.3
~6.5 16.3~6.5 16.3~6.6
11.5 11.5 11.4
18.5
18.5 24.5
22.0
22.0 28.5
5.5 5.5 5.3
8.0
~5.0 8.0~5.0 8.1~4.8
7.0 7.0 6.9
14.0
14.0 16.5
3.3
~51.9 3.3~51.9 2.5~51.7
46.4
46.4 43.8
23.3
~31.9 23.3~31.9 22.5~31.7
400V/3 Ph/50Hz
46
~4.4 0.46~4.4 0.60~5.94
01
~19.1 0.66~6.35 0.87~8.57
10
~12 10~12 12~18
74
×539×
947
1074×539×
947
1120×539×
947
96 99 120
ered with an isothermal cover, iltrati
on system
are subject to adjustment periodically or technical improvement without urther notice. For

FOR INSTALLERS AND P
ROFESSIONALS
1.
1.1. When sto ing o moving the heat pump, the heat pump should be at the up ight
position.
1.2. When moving the heat pump, do not lift the wate union since the titanium heat
exchange inside the heat pump will be damaged.
2.
INSTALLATION AND MAI
The heat pump must be installed by a p ofessional team. The use s a e not qualified
themselves, othe wise the heat pump might be damaged and isky fo use s’ safety.
2.1. Notice befo e installation
：
2.1.1. The
inlet and outlet water unions
connected with hard pipes!
2.1.2.
In order to guarantee the heating e iciency, the water pipe length should be
the pool and the heat pump.
10
ROFESSIONALS
1.
TRANSPORTATION
1.1. When sto ing o moving the heat pump, the heat pump should be at the up ight
1.2. When moving the heat pump, do not lift the wate union since the titanium heat
exchange inside the heat pump will be damaged.
INSTALLATION AND MAI
NTENANCE
The heat pump must be installed by a p ofessional team. The use s a e not qualified
themselves, othe wise the heat pump might be damaged and isky fo use s’ safety.
：
inlet and outlet water unions
can’t
bear the weight o so t pipes. The heat
In order to guarantee the heating e iciency, the water pipe length should be
the pool and the heat pump.
1.1. When sto ing o moving the heat pump, the heat pump should be at the up ight
1.2. When moving the heat pump, do not lift the wate union since the titanium heat
NTENANCE
The heat pump must be installed by a p ofessional team. The use s a e not qualified
to install by
themselves, othe wise the heat pump might be damaged and isky fo use s’ safety.
bear the weight o so t pipes. The heat
pump must be
In order to guarantee the heating e iciency, the water pipe length should be
≤10mbetween

FOR INSTALLERS AND
PROFESSIONALS
2.2. Installation inst uction
2.2.1. Location and size
To avoid air recirculation, the heat pump should be installed in a place with good ventilation or should reserve
su icient space or installation and maintenance. Please re er to the schema below:
* MINIMUM DISTANCE
Filte
Wate p ocesso
Wate switch
11
PROFESSIONALS
To avoid air recirculation, the heat pump should be installed in a place with good ventilation or should reserve
su icient space or installation and maintenance. Please re er to the schema below:
To avoid air recirculation, the heat pump should be installed in a place with good ventilation or should reserve

FOR INSTALLERS AND
PROFESSIONALS
※
Above data is
2.2.2.Heat pump installation.

The rame must be ixed by bolts
oundation must be solid; the bracket must be strong enough and anti

The heat pump needs a water pump
speci ication-
lux: re er to Technical Parameter, Max. li t

When the heat pump is running, there will be condensation water discharged rom the bottom,
please pay attention
to it. Please insert the drainage tube(accessory) into the hole and clip it well,
then connect a pipe to drain o the condensation water.
2.2.3.Wiring & protecting devices and cable speci ication

Connect to appropriate power supply, the voltage should c
products.
 Well earth the heat pump.

Wiring must be connected by a pro essional technician according to the circuit diagram.

Set breaker or use according to the local code (leakage operating current
 The layout o
power cable and signal cable should be orderly and not a ecting each other.
UNIT=MM
MODEL
IXCR26
IXCR36
IXCR46
IXCR56
IXCR66
IXCR80
IXCR80T
IXCR110T
12
PROFESSIONALS
Above data is
subject to modification without notice.
The rame must be ixed by bolts
(M10)
to concrete oundation or brackets. The concrete
oundation must be solid; the bracket must be strong enough and anti
-
The heat pump needs a water pump
(Supplied by the use )
. The recommended pump
lux: re er to Technical Parameter, Max. li t
≥10m
When the heat pump is running, there will be condensation water discharged rom the bottom,
to it. Please insert the drainage tube(accessory) into the hole and clip it well,
then connect a pipe to drain o the condensation water.
2.2.3.Wiring & protecting devices and cable speci ication
Connect to appropriate power supply, the voltage should c
omply with the rated voltage o the
Wiring must be connected by a pro essional technician according to the circuit diagram.
Set breaker or use according to the local code (leakage operating current
power cable and signal cable should be orderly and not a ecting each other.
A B C D E F
407 528 390 432 893 280
407 574 390 432 939 350
407 630 390 432 995 460
404 760 384 429 1125 600
514 710 493 539 1074 640
514 710 493 539 1074 640
514 900 493 539 1264 650
subject to modification without notice.
to concrete oundation or brackets. The concrete
-
rust treated;
. The recommended pump
When the heat pump is running, there will be condensation water discharged rom the bottom,
to it. Please insert the drainage tube(accessory) into the hole and clip it well,
omply with the rated voltage o the
Wiring must be connected by a pro essional technician according to the circuit diagram.
Set breaker or use according to the local code (leakage operating current
≤ 30mA).
power cable and signal cable should be orderly and not a ecting each other.
G H
74 650
74 650
74 750
74 952
74 947
74 947
74 947

FOR INSTALLERS AND
PROFESSIONALS
1. Wi ing diag am
NOTE:
Must be hard wired, no
plug allowed

For your sa e use in winter, it’s strongly recommended to equip heating priority unction.

For the detailed wiring diagram, please re er to Appendix
3. Options fo p otecting devices and cable specification
MODEL IXC
R2
B eake
Rated Cu ent A
Rated Residual Action
Cu ent mA 30
Fuse A
Powe Co d（mm
2
）
Signal cable（mm
2
）
3×0.5
NOTE: The above data is adapted to powe co d ≤ 10m.If powe co d is
be inc eased. The signal cable can be extended to 50m at most.
A. Fo powe supply: 230V 50Hz
Distribution Box(Customer prepare)
Power Supply
400V 50Hz
Breaker
Distribution Box(Customer prepare)
Power Supply
230V 50Hz Breaker
B. Fo powe supply: 400V 50Hz
Earthing
Earthing
13
PROFESSIONALS
plug allowed
.
For your sa e use in winter, it’s strongly recommended to equip heating priority unction.
For the detailed wiring diagram, please re er to Appendix
1.
3. Options fo p otecting devices and cable specification
R2
6 IXCR36 IXCR 6 IXCR56 IXCR66 IX
C
15.0 19.0 22.5 24.5
28.5
30 30 30 30
30
15.0 19.0 22.5 24.5
28.5
3×2.5 3×4 3×4 3×6
3×
3×0.5
3×0.5 3×0.5 3×0.5 3×0.5
3×0.5
NOTE: The above data is adapted to powe co d ≤ 10m.If powe co d is
＞
10m, wi e diamete must
be inc eased. The signal cable can be extended to 50m at most.
A. Fo powe supply: 230V 50Hz
Distribution Box(Customer prepare)
Power Cord
Swimming Pool Heat Pump Wiring Board
Distribution Box(Customer prepare)
Power Cord
Swimming Pool Heat Pump Wiring Board
B. Fo powe supply: 400V 50Hz
Fuse
Fuse
For your sa e use in winter, it’s strongly recommended to equip heating priority unction.
C
R80 IXCR80T IXCR110T
28.5
30
30 30
28.5
3×
6
3×0.5
3×0.5 3×0.5
10m, wi e diamete must
Swimming Pool Heat Pump Wiring Board
Swimming Pool Heat Pump Wiring Board

FOR INSTALLERS AND
PROFESSIONALS
2.3. T ial afte installation
Please check all the wi ings ca efully befo e tu ning on the heat pump.
2.3.1．Inspection be ore use

Check installation o the whole heat pump and the pipe connections according to the pipe
connecting drawing;

Check the electric wiring according to the electrical wiring diagram and earthing connection;

Make sure that the main power is well connected;

Check i there is any obstacle in ront o the air inlet and outlet o the heat pump
2.3.2．Trial
 The user is
advised to start the water pump be ore the heat pump, and turn o the heat pump
be ore the water pump or long li e circle.

The user should start the water pump, and check or any leakage o water; Power on and press
the ON/OFF button o the heat pump, an

In order to protect the heat pump, the heat pump is equipped with start
starting the heat pump, the an will start to run in 3 minutes, in another30 seconds, the
compressor will start to run.

A ter pool heat pump starts up, check or any abnormal noise rom the heat pump.

Check the temperature setting
2.4. Maintenance and winte izing
2.4.1 Maintenance
The maintenance should be ca ied out once pe yea by qualified p ofessional technici
 Cut o power supply o the
heat pump be ore cleaning,
examination and repairing .
Do not touch the electronic
components until the LED
indication lights on
PCB turn o .

Please clean the evaporator with household detergents or clean water, NEVER
thinners or any similar uel.

Check bolts, cables and connections regularly.
2.4.2 Winterizing
In winter season when you don’t swim, please cut o power supply and drain water out o the heat
pump. When using the heat pum ℃
14
PROFESSIONALS
Please check all the wi ings ca efully befo e tu ning on the heat pump.
Check installation o the whole heat pump and the pipe connections according to the pipe
Check the electric wiring according to the electrical wiring diagram and earthing connection;
Make sure that the main power is well connected;
Check i there is any obstacle in ront o the air inlet and outlet o the heat pump
advised to start the water pump be ore the heat pump, and turn o the heat pump
be ore the water pump or long li e circle.
The user should start the water pump, and check or any leakage o water; Power on and press
the ON/OFF button o the heat pump, an
d set desired temperature in
the thermostat
In order to protect the heat pump, the heat pump is equipped with start
starting the heat pump, the an will start to run in 3 minutes, in another30 seconds, the
A ter pool heat pump starts up, check or any abnormal noise rom the heat pump.
.
2.4. Maintenance and winte izing
The maintenance should be ca ied out once pe yea by qualified p ofessional technici
PCB turn o .
Please clean the evaporator with household detergents or clean water, NEVER
Check bolts, cables and connections regularly.
In winter season when you don’t swim, please cut o power supply and drain water out o the heat
mp under 2 , make ℃
sure there is always water low.
Impo tant:
Unscrew the water union o inlet pipe
to let the water low out.
When the water in machine reezes in
winter season, the titanium heat
exchanger may be damaged.
Please check all the wi ings ca efully befo e tu ning on the heat pump.
Check installation o the whole heat pump and the pipe connections according to the pipe
Check the electric wiring according to the electrical wiring diagram and earthing connection;
Check i there is any obstacle in ront o the air inlet and outlet o the heat pump
advised to start the water pump be ore the heat pump, and turn o the heat pump
The user should start the water pump, and check or any leakage o water; Power on and press
the thermostat
.
In order to protect the heat pump, the heat pump is equipped with start
delay unction. When
starting the heat pump, the an will start to run in 3 minutes, in another30 seconds, the
A ter pool heat pump starts up, check or any abnormal noise rom the heat pump.
The maintenance should be ca ied out once pe yea by qualified p ofessional technici
an.
Please clean the evaporator with household detergents or clean water, NEVER
use gasoline,
In winter season when you don’t swim, please cut o power supply and drain water out o the heat
sure there is always water low.
Unscrew the water union o inlet pipe
When the water in machine reezes in
winter season, the titanium heat

FOR INSTALLERS AND
PROFESSIONALS
3. TROUBLE SHOOTING
FAILURE
Heat pump doesn’t un
No power
Power switch is o
Fuse burned
The breaker is o
Fan unning but with
insufficient heating
evaporator blocked
Air outlet blocked
3 minutes start delay
Display no mal, but no
heating
Set temp. too low
3 minutes
I above solutions don’t work, please contact your installer with detailed in ormation and your model number.
Don’t try to repair it yoursel .
ATTENTION！
Please don’t t y to epai the heat pump by you self to avoid any isk.
15
PROFESSIONALS
3. TROUBLE SHOOTING
FOR
COMMON FAULTS
REASON
SOLUTION
No power
Wait until the power recovers
Power switch is o
Switch on the power
Fuse burned
Check and change the use
The breaker is o
Check and turn on the breaker
evaporator blocked
Remove the obstacles
Air outlet blocked
Remove the obstacles
3 minutes start delay
Wait patiently
Set temp. too low
Set proper heating temp.
3 minutes
start delay Wait patiently
I above solutions don’t work, please contact your installer with detailed in ormation and your model number.
Please don’t t y to epai the heat pump by you self to avoid any isk.
COMMON FAULTS
SOLUTION
Wait until the power recovers
Switch on the power
Check and change the use
Check and turn on the breaker
Remove the obstacles
Remove the obstacles
Set proper heating temp.
I above solutions don’t work, please contact your installer with detailed in ormation and your model number.
Please don’t t y to epai the heat pump by you self to avoid any isk.

FOR INSTALLERS AND
PROFESSIONALS
NO. DISPLAY
1 E3
No water protection
2 E5
Power supply excesses operation range
3 E6
Excessive temp di erence between inlet and outlet water(Insu icient water low
protection)
4 Eb
Ambient temperature
5 Ed Anti-
reezing reminder
NO. DISPLAY
1 E1
High pressure protection
2 E2
Low pressure protection
3 E4
3 phase sequence protection (three phase only)
4 E7
Water outlet temp too high or too low
5 E8
High exhaust temp protection
6 EA
Evaporator overhe
7 P0
Controller communication ailure
8 P1
Water inlet temp sensor ailure
9 P2
Water outlet temp sensor ailure
10 P3
Gas exhaust temp sensor
11 P4
Evaporator coil pipe temp sensor ailure
12 P5
Gas return temp sensor ailure
13 P6
Cooling coil pipe temp sensor ailure
14 P7
Ambient temp sensor ailure
15 P8
Cooling plate sensor ailure
16 P9
Current sensor ailure
17 PA Restart
memory ailure
18 F1
Compressor drive module ailure
19 F2
PFC module ailure
20 F3
Compressor start ailure
21 F4
Compressor running ailure
22 F5
Inverter board over current protection
23 F6
Inverter board overheat protection
24 F7 Current
protection
25 F8
Cooling plate overheat protection
26 F9
Fan motor ailure
27 Fb
Power ilter plate No
28 FA
PFC module over current protection
16
PROFESSIONALS
4. FAILURE CODE
NOT FAILUREDESCRIPTION
No water protection
Power supply excesses operation range
Excessive temp di erence between inlet and outlet water(Insu icient water low
Ambient temperature
too high or too low protection
reezing reminder
FAILUREDESCRIPTION
High pressure protection
Low pressure protection
3 phase sequence protection (three phase only)
Water outlet temp too high or too low
protection
High exhaust temp protection
Evaporator overhe
at protection (only at cooling mode)
Controller communication ailure
Water inlet temp sensor ailure
Water outlet temp sensor ailure
Gas exhaust temp sensor
ailure
Evaporator coil pipe temp sensor ailure
Gas return temp sensor ailure
Cooling coil pipe temp sensor ailure
Ambient temp sensor ailure
Cooling plate sensor ailure
Current sensor ailure
memory ailure
Compressor drive module ailure
PFC module ailure
Compressor start ailure
Compressor running ailure
Inverter board over current protection
Inverter board overheat protection
protection
Cooling plate overheat protection
Fan motor ailure
Power ilter plate No
-power protection
PFC module over current protection
Excessive temp di erence between inlet and outlet water(Insu icient water low

FOR INSTALLERS AND
PROFESSIONALS
APPENDIX 1: HEATING
17
PROFESSIONALS
APPENDIX 1: HEATING
PRIORITY WIRING DIAG
RAM (OPTIONAL)
RAM (OPTIONAL)