Famree Smart Cat Litter Box User manual

User Manual
Smart Cat Litter Box ++
PCBM65A

EN
02
Cautions:
1. Please install and use this device according to the instructions.
2. Please use it indoors, do not place it in direct of sunlight or and fire sources.
3. Please place the device on a flat hard surface, and do not place articles on the top of
the device.
4. Do not drag or place vigorously during placement to avoid device damage.
5.Cats weighing less than 2.2lb/1kg and lactating cats should not use the device under
auto cleaning mode.
6. Do not soak or immerse the electric parts of this device.
7. Please unplug the power cord when moving, cleaning the device, or not using it for
a long time.
8. Please use the original power adapter to avoid damage to the device or potential
safety hazards .
9. If children use this device, please make sure to use it under the guidance of parents
or guardians.
10. Please perform maintenance under the guidance of professionals to avoid all kinds
of damages.
11. If you encounter product related issue, please contact our customer service.
12. Please read t his manual carefully before use. Once installed and used, it is seen that
you have carefully read and accepted the following safety instructions.
13. If the product does not work correctly due to other unknown conditions, please
simply restart the power by unpluging and pluging-in the cord.
EN
01
BEFORE USE
1. Please place the device on a firm and flat ground.
2. Please add litter below MAX line after placing the device well.
3. Please power on the device and wait it to finish self-check.Then it is ready to use.
CONTENT
BEFORE USE…………………………………………………………….........……………01
ⅠINSTRUCTIONS FOR THE FIRST USE………………………………..........…………03
ⅡAPP …………………………………………………………………...................………07
ⅢOPERATING INSTRUCTIONS ……………………………………..............…………11
ⅣFAULT SELF-CHECK METHOD…………………………………….............…………28
ⅤFAQ ………………………………………………………………..................…………29
ⅥPRODUCT LIST …………………………………………………..............…………… 31
ⅦINTRODUCTION OF CONTROL PANEL …………………….......…….……………32
ⅧCIRCUIT DIAGRAM ……………………………………………......................……… 33
IX PARAMETERS AND SPECIFICATIONS………………………........…………………34

m
U
a
s
n
e
u
r
al
EN EN
03 04
I INSTRUCTIONS FOR THE FIRST USE
1.1 Unpacking:
Turn over the carton to cut the tape from the bottom, then turn over the carton to
pull up the carton vertically.
1.2 Placement:
Place the device on the flat ground and make sure all four feet of the product con-
tact the flat and hard surface.
To avoid the cat identification sensor malfunction, please keep a 1 ft clear space for
the device if the object is over 2 inches tall.
1.3 What is in the box?
Power Adapter with Anti-bite Cord x 1
Manual x 1
17.7"*19.7"/4 Gallon Trash
Bag x 1 roll
Notice:
√The four feet of the product must be in contact with a firm flat ground!
×Place the machine on the soft carpet .
×Place the two front feet of the device on the cat litter mat or rug.
Notice:
Please review the installation instructions of Trash Bag,
or scan the code below to watch the video.
Adapter (anti-bite) Trash Bag User manual

EN EN
05 06
1.4 Adding Litter:
Make sure the leveled litter height is between the MAX line and the MIN line (based
on your actual need).
1.5.1 Power on the device with pluging in the adapter and wait for the machine to
self-check for about 3-8 minutes. It will automatically enter the sensing stage after
self-check. No need to change its mode at this point.
1.5.2 After the cat litters and leaves, the device will automatically clean up in 3 minutes to
allow enough time for the cat leaves and cat excrement clumps. Then the cleaning
process will take 4 minutes to complete.
1.5.3 After cleaning, the device will automatically start the smell elimination and disinfec-
tion process which will last around 30 minutes.
Notice:
× Pick up or drag the device after powering up. (This will interfere with weight calibration in
the reset program.)
① If you place the device in a narrow space, or there is an infrared interference source in
front of the device, the device self-check may take about 8 minutes. Please wait patiently.
② Suppose the sensor has detected the space is not suitable for work. In that case, the
detection function will be automatically disabled after the self-check is completed. The
weight detection system will detect whether the cat enters automatically.
③ During the cleaning process, all keys will be suspended. Please wait until the cleaning pro-
cess is completed if you need the device to perform other functions.
MAX Line
The amount of cat litter should
not exceed Max line.
MIN Line
The amount of cat litter should
not be lower than Min line.
1.5 Power On:

II APP
2.1 App Installation
Method 1: You can scan the above
QR Code with your mobile phone
Method 2: You can download "tuya"
App from the App store.
2.2 Networking:
2.2.1 Confirm that the phone is connect-
ed to 2.4G WiFi, then turn on the Blue-
tooth and Location
2.2.2 Press "Auto" for 2 seconds,
when the WiFi indicator starts flash-
ing, the device is ready to be con-
nected.
Attention: Touch only word
characters (not the picture char-
acters) can make the device
work.
2.2.3 Open the App to add equip-
ment or let the App scan automati-
cally.
EN EN
07 08
Flash
Press for 2s

Notice:
If the network configuration fails or a timeout message is displayed, please follow the
connections fix process as below:
①WiFi, Bluetooth, and Location switch are enabled simultaneously.
②WiFi connection is in the 2.4Gband network. (The product can notrecognize the 5Gband
network.)
③WiFi indicator is flashing during network configuration.
④WiFi network in your home is functioning
⑤WiFi password is correct.
⑥WiFi signal is weak and the WiFi needs to be closer to the device.
⑦The router connects to many wireless devices, causing IP address conflicts.
2.2.6 Enter APP afte connecting.2.2.4 Press "Next" after scanning
thedevice.
2.2.5 Press " Next " after entering the
WiFi password and wait to connect.
EN EN
09 10

III OPERATING INSTRUCTIONS
3.1 Auto Mode:
Click "Auto" on the panel or the App to start auto-sensing for cats in / out and auto
cleaning. It is the default mode once the device has powered-on and self-checked.
Notice:
①Please click "Auto" on the panel or the App to turn-off the auto-sensing feature if the cat is
less than 2.2 lb (1kg) or the cat is pregnant. When the device needs cleaning, you will
need to click "Clean" to start the cleaning process.
②To clean litter quicker, you can adjust the "cleaning wait time" in the App, for example, 1
minute, in that way you can clean as quickly as possible and reduce the smell. For families
with two or more cats, you can adjust the "cleaning interval" in the App to avoid repeated
ineffective cleaning of the device.
③If the cat enters the bin for more than 10 seconds, the cat is considered to have potty
behavior. After the cat leaves for 3 minutes, the automatic cleaning procedure will be
performed. (The default interval between cleanups is 15 minutes to prevent the device from
cleaning too frequently during multiple cats' use. The device might not work after the
second cat pees; the interval of two pees is less than 15 minutes.)
④If the App froze, please check the network status or re-configure the network, or click the
corresponding button on the App and repeat once or twice.
EN EN
11 12

3.2 Clean Mode:
Click "Clean" on the panel or the App to start clearing process.
Notice:
①During the clearing process, all keys will be disabled. If you need to perform other func-
tions,please wait until the clearing process is complete.
②Extend the cleaning time in the phone App when the cat has diarrhoea. It allows the cat
litter to take enough time to clump and reduce the pollution of soft feces to the bin.
③If you have restarted the device, the waiting time of the "Cleaning" procedure will be
restored to the default by 3 minutes, which can be reset in the APP if necessary. (setting
range: 0 to 60 minutes)
④Extend the interval between two cleanings when you have multiple cats, preventing
repeated device cleaning. ⑤If you have restarted the device, the interval time between
two clearings will be restored to the default by 15 minutes, which can be reset in the APP
if necessary. (setting range: 0 to 120 minutes)
EN EN
13 14

MAX Line
The amount of cat litter should
not exceed Max line.
MIN Line
The amount of cat litter should
not be lower than Min line.
3.3 Add cat litter:
Method 1:
In "Auto" mode, when the adding cat litter is more than 2 lb (1kg), the "Auto" will start
flashing. After 30 minutes, the cat litter will be automatically smoothed, and the weight will
be calibrated. Hold the 'Remove odor' button for 2 seconds or more to adjust the time.
The cat litter will be smoothed, and the weight will be calibrated immediately.
Method 2:
Please turn off the power, add the litter and turn on the power.
Notice:
①The machine will not interrupt when it is smoothing litter, even the cat enters. The device
spin gently and will not hurt cats. During cleaning process the device has protection and it
will stop once the cats get close to the entrance.
②Please make sure the height of the litter is between the MIN line and MAX line. If not,
please adjust the amount of litter using method 2.
③You can find the litter surface level correction option on the App to adjust the litter posi-
tion manually. (For grade 0, the litter surface leans to the right, and in grade 6, the sand
surface leans to the left.)
EN EN
15 16

3.4 Replace litter:
①Replace the garbage bag with a new one (the original one is already full of polluted litter
and bacteria)
②Make sure the remaining litter is close to the MIN line (to avoid the overflow when the bin
rotates)
③Press "Replace Litter" for 2 seconds, then wait for the device to clear the rest litter (about 3
minutes)
④Replace the garbage bag with a new one again after clearing litter
Notice: ①Click "Replace Litter" again to cancel if you clicked it by mistake or forgot to
replace the garbage bag.
②For fine mineral litter, when replacing the bag (step ①), you can hold the "Clean" button
for 2 seconds to avoid the overflow from the bag opening. The litter bin will rotate 90 °
counterclockwise to ensure that the opening of the bag is upward when replacing. After
Replacing garbage bag, repeat ③and ④.
EN EN
17 18

60″
TightenUp
Pull
Press
Wind
3.5 Remove Odor:
Method 1:
Click "Remove Odor" on the panel or click "Odorless" on the App.
Method 2:
Set regular work on your App. 3.6 Replace Garbage Bag: When indicator "Full" is on,
you will need to replace the garbage bag.
Notice:
①The device will remove odor automatically for 30 minutes after every cleaning.
②It will stop once the cat enters and continue to work after the cat leaves.
3.6 Replace Garbage Bag:
When indicator "Full" is on, you will need to replace the garbage bag.
EN EN
19 20
①Hold the "Clean"
button for 2 seconds, wait
for the waste bin to
change the position,
open the waste bin and
take out the used
garbage bag.
②It will take 60 seconds
to change the waste bin
position. Then, the device
automatically returns after
60 seconds. If the new
garbage bag is not
placed within 60seconds,
you can continue after the
device is returned.
③The drawstring of the
new garbage bag is
aligned with the tie uppile
and the lower edge of the
bag opening is clamped
under the locating clip.
④Wrap the garbage bag
around the outer frame of
the waste bin gate, and
pull out the drawstring.
⑤Press the drawstring
into the tie-up pile,
tighten and wind it.
ii
⑥After the installation,
confirm that the automat-
ic flip-door of the waste
bin is not blocked and
can open and close
normally. Place the rest
part of the garbage bag
to the empty room of the
waste bin, to prevent it
being trapped by the
wastebincover.
LocatingClip
Winding

Notice:
①The "Full" indicator is only for reference. The "Full" indication may vary depending on the
cat litter volume, density, and fluidity. You can adjust the delay of the "Full" sign on the
App based on your preferences. The default is 0 (there is still a little space in the bag for
garbage), and the The maximum value is 15.
②If you have restarted the machine, the delay of the "Full" prompt will be restored to the
default,which is 0. It can be reset in the APP if necessary.
③Normally, the waste bin storage capacity of 1 cat can be up to 15 days, and for 3 cats can
be up to 5 days. Users can replace the garbage bag every five days, depending on the
actual situation.
EN EN
21 22

3.7 Wash Barrel:
① Power off the device first!
② Open the buckle of the barrel compartment and lift the bin.
③ Wash and dry the barrel before placing it back on the base!
3.8 Lock the Panel:
Press the "Auto" and "Remove Odor" at the same time for more than 2
seconds to turn on and off the "Child Lock". You can also use the "Child Lock"
Lock" button on the App.
Notice:
If the indicator of the Bin sign is on, please restart the machine or click "Clean"
EN EN
23 24
Waste bin
Entrance
Barrel shaft Fixed groove
Host
4 Weight sensors Display and Control Panel
Clasp
Power socket
Ion Purification module
Barrel
Press "auto" + "Remove odor" 2 seconds

3.9 Turn On / Off the Infrared Sensor:
Press "Clean" and "Replace litter" at the same time for more than 2 seconds if the device is
placed in a cage or a narrow space. Or click the bucket infrared sensor option in the APP
to turn on or off the infrared sensor.
3.10 Various Timing Operations of The App
3.10.1 Sleep Mode When the device is placed in the bedroom, you can set in the App "Do
not Disturb Timing" to prevent the night-time activation of the device.
Notice:
① When the DND (Do not Disturb) mode is on, the light on the panel will be off. Touch
any button to exit the DND (Do not Disturb) mode.
② If the device is clearing when setting DND (Do not Disturb), it will enter the DND (Do
not Disturb) stage after the cleaning is complete.
EN EN
25 26
Press "Clean" + "Replace litter" 2 seconds

IV FAULT SELF-CHECK METHOD
3.10 Various Timing Operations of The App
3.10.2 Timer Cleaning Mode Set the device to clean regularly in the App "Clean Timing".
3.10.3 Timing Odor Removing: Set the device to remove odor regularly in the App
"Deodo Timing".
4.2 Testing Mode:
①Press each key to check whether the key works properly. If it works properly, the PCB
hardware is functioning correctly.
②Press the device from the top with a force of more than 2.2 lb (1kg) to see whether the
"Full" indicator flashes. If it does, the gravity sensor is functioning correctly.
③If the Bin indicator keeps lighting up, the motor is working correctly.
④If the WiFi indicator keeps lighting up, the WiFi hardware is functioning correctly.
⑤Cover the infrared sensor at the barrel entrance, if the "Auto" mark flashes, the sensor
functions correctly.
4.3 Restart the device after the testing mode is completed.
Notice:
Suppose the execution time of these scheduled procedures overlaps with the DND
(Do not Disturb). In that case, the product will first perform odor cleaning and then
return to DND mode.
EN EN
27 28

V FAQ
Q: Why is the weight data only about half of that of my cats?
A: Please check if the cat enters only halfway out of curiosity, or if the device is placed
on flat ground and a hard surface.
Q: Why is the App showing motor failure, why is the fault indicator lighted on the
equipment panel/why is the equipment always self-checking?
A: If the self-check takes more than 15 minutes, the fault indicator is on. It may be that
the barrel compartment is not installed correctly or something is stuck.
Please open the buckle of the barrel compartment, lift the barrel to inspect, and then
put it back according to the tips (on the base) and close the buckle.
Q: Why does the clearing takes so long?
A : Lower revs make timid cats less scared. It will prolong the whole clearing time if cats
enter or come closer frequently out to curiosity.
Q: Why the machine rotates back for a while before finishing the whole rotation?
A: To save litter and increase the capacity of the collection bin.
Q: Why the poop can't be cleaned in the garbage box?
A: It could be caused by garbage bag jam by cat litter. Please inspect the garbage bag
port to see if it can be fully opened and close. (it is recommended to check every
time after installing a new bag). The large size of garbage can be handled manually
to make it smaller first.
Q: What kind of cat litter sand should I use?
A: Mixed sand and tofu sand are preferred. Bentonite sand and mineral sand are okay, this
may affect the delay time of the "Full" prompt due to their weight density and liquidity.
Q: Why is there some litter sand left in the bin after using the "Replace Litter" function?
A: Please check the garbage bag space to see if there is enough space. Please replace the
bag and then "Replace Litter" again.
Q: Why is the litter sand leaking out from the port of the garbage box when replacing the
garbage bag? A: Please hold the "Clean" for 2 seconds, and then the litter bin will rotate
90° counterclockwise to ensure that the port of the bag is upward when replacing.
Q: Why is the weight data incorrect?
A: Please hold the "Remove Odor" for 2 seconds, the litter sand will be smoothed, and the
weight will be calibrated. Also, please check whether the device is placed on a flat and
hard surface. If a cat enters the bin during working, it will also get an inaccurate weight.
Cats entering halfway or staying in the bin for too short of time may also result in incorrect
weighing.
Q: Why didn't the device stop working while the cat entered?
A: The device won't stop when sand leveling and weight calibrating. The device is designed
with a safe structure. Rotating 45 degrees is safe when the cat enters.
EN EN
29 30

VI PRODUCT LIST VII INTRODUCTION OF CONTROL PANEL
EN EN
31 32
Waste bin
Wifi
Host key
Indicator
Category Function Operation Status Prompt
tone
Clean Click Start cleaning immediately One ring
Replace litter Press Start replacing cat litter Longringfor 1″
Auto cleaning Click Start Auto cleaning One ring
Remove odor Click Start purifying the air One ring
Join network Press Reset WiFi to start
join network Longringfor 1″
Leveling Press Leveling the cat litter Longring for 1″
Change garbage bag Press Adjust the barrel angle to
the bag changing position Longring for 1″
Lock/Unlock Press Locked/Unlock Longringfor 3″
Ring lamp Lighting Power On
Fault lamp (left) Lighting Barrel is not installed
or it cannot run
Lighting The device is connected
Flash The device is trying to
connect to the network
WiFi lamp (middle)
Unlit The device is not connected
Waste full lamp (right) Lighting
for 2″
for 2″
for 2″
for 2″
for 2″
+
Remind users to replace
garbage bag when the
waste bin is almost full
Entrance
Barrel Shaft Fixed Groove
Host
Weight sensors* 4 Display and Control Panel
Clasp
Power socket
Ion Purification Module
Barrel
Full

VIII CIRCUIT DIAGRAM IX PARAMETERS AND SPECIFICATIONS
EN EN
33 34
Product Name
Smart Cat Litter Box
Rated Voltage
DC12V
Product Model
PCBM65A
ID:MSP-01
Rated Power
≤18W
Whole Machine Size
18.8"(W)×20.47"(D)×19.88"(H)mm
Suggested Pet Type
Cat
Human Body
Sensors
Main Control BoardInput DC 12V 1.5A
Hall Sensors
IonGenerator DC 12V 2W
Weight
Sensors
WiFi Module
Display And
Control Panel
Fan
Motor
19.88" 9.64"
18.8" 20.4"
19.88"
19.88"

PLEASANT LITTER EXPERIENCE
FOR BOTH CATS & CAT FANCIERS
Thank you for for purchasing Famree Self Cleaning Cat Litter Box. If you have any questions or issues, please contact our
customer service team for futher assistance.
Email: [email protected]
Tell-Free Call: (877)-756-8666
Service Time: Mon.-Fri: 9:00 -17:00