Fantasea Line FA6000 User manual

FA6000 Housing Instruction Manual 20190204
Fantasea Line
FA6000 Housing
For Sony a6000
(Cat. No. 1519)
Instruction Manual

FA6000 Housing Instruction Manual 20190204
2
TABLE OF CONTENTS
TABLE OF CONTENTS................................................................................................................................ 2
DISCLAIMER............................................................................................................................................. 3
INTRODUCTION ....................................................................................................................................... 3
FEATURES & SPECIFICATIONS................................................................................................................... 4
INCLUDED IN PACKAGE............................................................................................................................ 4
IDENTIFICATION OF HOUSING PARTS....................................................................................................... 6
SONY A6000 MIRRORLESS DIGITAL CAMERA.......................................................................................... 15
SETTING UP THE HOUSING..................................................................................................................... 16
PREPARING THE CAMERA..................................................................................................................................... 16
WHEN USING THE HOUSING FOR THE FIRST TIME ....................................................................................................... 17
INSTALLING M16 PORT ACCESSORIES .................................................................................................................... 19
MOUNTING AND REMOVING LENS PORTS ............................................................................................................... 20
OPENING THE HOUSING...................................................................................................................................... 23
CHECKING THE O-RING ....................................................................................................................................... 24
INSTALLING THE CAMERA .................................................................................................................................... 25
CLOSING THE HOUSING....................................................................................................................................... 28
REMOVING THE CAMERA FROM THE HOUSING ....................................................................................................... 29
OPTIONAL ACCESSORIES........................................................................................................................ 31
UNDERWATER FLASHES &STROBES....................................................................................................................... 31
LED FLASH TRIGGERS ......................................................................................................................................... 33
FLASH &VIDEO LIGHTING SETS............................................................................................................................. 33
INTERCHANGEABLE LENS PORTS ............................................................................................................................ 33
LENS ACCESSORIES ............................................................................................................................................. 34
COLD-SHOE CONNECTOR FOR LIGHTING ACCESSORIES............................................................................................... 34
M16 PORT ACCESSORIES .................................................................................................................................... 34
MOISTURE DETECTOR......................................................................................................................................... 34
CARE & MAINTENANCE.......................................................................................................................... 35
FANTASEA PRODUCT CONSUMER LIMITED WARRANTY.......................................................................... 36
FANTASEA MOISTURE DETECTOR........................................................................................................... 37
IDENTIFICATION OF PARTS.................................................................................................................................... 37
SILENCING THE ALARM........................................................................................................................................ 38
REPLACING BATTERIES ........................................................................................................................................ 38
REPLACING THE ALARM UNIT ............................................................................................................................... 39

FA6000 Housing Instruction Manual 20190204
3
DISCLAIMER
While every effort has been made in order to ensure that the information included in this instruction
manual is accurate and complete, no liability will be accepted for any errors or omissions. Fantasea Line
reserves the right to change product specifications and features described herein at any time without prior
notice. No part of this instruction manual may be copied, translated or reproduced without the prior
written permission of Fantasea Line. Fantasea Line makes no warranties aside from limited product
warranty as described at the end of this manual.
INTRODUCTION
The FA6000 Housing features a stylish and ergonomic design, specifically created for the Sony a6000
mirrorless digital camera. The FA6000 Housing is manufactured to the highest professional standards of
function, style and durability. It is depth rated to 60m/200 feet and features ergonomically designed and
labeled controls. The Fantasea FA6000 is the ultimate waterproof home for the Sony a6000 camera.
The FA6000 Housing is ideal for outdoor and underwater photography. Underwater photographers can dive
or snorkel and capture all the excitement of this fascinating world, while outdoor photographers also have
the option of capturing the action of outdoor and water sports activities, such as paddle sports, sailing,
boating, surfing, fishing, hunting, backpacking and camping. The FA6000 Housing is shock resistant and
protects the camera from water, sand, dust, frost, impact, as well as other damaging elements and harmful
occurrences. The FA6000 Housing was designed to be compatible with a complete accessory system,
enabling photographers to enhance the quality of their images.
IMPORTANT
NOTICE
Please read this manual carefully in order to properly operate the FA6000
Housing. Store this manual in a safe place for further reference once you have
read it.

FA6000 Housing Instruction Manual 20190204
4
FEATURES & SPECIFICATIONS
Depth rated to 60m/200 feet
Made from durable injection molded Polycarbonate
Access to all essential camera controls and functions with clearly labeled controls
Shock resistant
Double O-ring protection for a perfect watertight seal
M16 port for a variety of connections, including HDMI, vacuum valve or electronic strobe triggering
bulkheads
Special cold-shoe mount for lighting accessories
Double fiber optic cable port
Removable anti-glare hood for the LCD screen
Easy and secure installation of camera
Moisture Detector and Alarm
Protective housing body cap
Extended shutter release included for easy access when using housing tray and handles
Interchangeable lens port and lens gear accessories are available, allowing for the use of a wide
range of lenses
Additional optional housing accessories are available
Weight (without camera and lens port on land): 980g / 34.5 oz
Weight (with camera and FML Flat Port on land): 1,645g / 58 oz
Dimensions (without accessories): 20.5 x 14.5 x 15.5 cm \ 8 x 5.7 x 6.1 inch (W x D x H)
Manufacturer’s warranty
INCLUDED IN PACKAGE
(Corresponding numbered images appear on the following page)
1. FA6000 Housing
2. Housing protective body cap
3. Nano fiber optic plug adaptor x 2
4. Hand lanyard
5. Extended shutter release
6. Anti-glare hood for LCD screen
7. Sticker for camera flash
8. FML1 lens port opening tool
9. Screwdriver
10.Silica gel packs
11.Silicone grease
12.O-ring remover
13.Spare back door O-ring seal
14.Lens cloth

FA6000 Housing Instruction Manual 20190204
5
6
8
9
10
4
11
7
13
12
14
3
2
1
5

FA6000 Housing Instruction Manual 20190204
6
IDENTIFICATION OF HOUSING PARTS
Housing View #1 –Top/Front - Corresponding numbered descriptions are listed on the following page
Note
1. Please refer to the Sony a6000 camera instruction manual for detailed
descriptions and instructions regarding all camera controls and
functions.
2. It is strongly recommended that you familiarize yourself with all the
controls topside before using these controls underwater.
1. Shutter Release
2. On/Off
4. Control Dial
8. Cold Shoe Mount
9. M16 Port
11.Lens Dial
12.Interchangeable Lens
Port System
(Lens Ports are supplied
separately)
3. C1 Button
5. Non-Functional
Control
6. Mode Dial
7. Flash Push-Down Control
10.Double Fiber
Optic Cable Port
13. Lanyard Loop
13.Latch Dial Lock
15.Latch Dial

FA6000 Housing Instruction Manual 20190204
7
Numbered descriptions below refer to corresponding numbers on the top/front housing graphic on the
previous page:
1. Shutter Release –Activates the camera shutter release button and auto focus prior to taking the
picture.
Note that the shutter release trigger can be replaced with an extended trigger (included in the
package) for easier access when the housing is mounted on a tray & handle/arm system. For further
instructions please refer to the section “Preparing the Housing”.
2. On/Off- Pushing this control activates the camera power switch button and turns the camera on/off.
3. C1 Button –Pushing this control activates the camera C1 (Custom 1) button. Various functions can be
assigned to this button through the camera menu, providing access to favorite and most frequently
used settings, thereby allowing quick operation based on your personal preferences and shooting
habits.
4. Control Dial –Turn this dial to quickly adjust settings in each shooting mode, fine-tune functions or
browse through menu items. Note that the function of the control dial in Manual exposure shooting
mode can be set through camera menus.
5. Non-Functional Control –Pushing this control does not activate any of the camera buttons. It also
doesn’t interfere with proper housing operation. Therefore, this control can be ignored while using
the housing.
6. Mode Dial –Turn this dial to change shooting modes.
7. Flash Push-Down Control –Pushing this control presses the built-in flash back into the camera body
after it has been popped-up by using the Flash Pop-Up control. Note that slight pressure should be
applied when pushing this control in order to completely press the built-in flash back into the camera
body. The built-in flash clicks once it has been properly pushed back down and this can also be
verified by a dedicated marking on the camera LCD screen.
8. Cold-Shoe Mount for Lighting Accessories- Enables mounting a flash, video light, torch or focus light
on top of the housing by using a dedicated connector. For further information regarding such
connectors, please visit the Fantasea website –www.fantasea.com

FA6000 Housing Instruction Manual 20190204
8
9. M16 Accessory Port –This port features a standard M16 thread hole and allows for optional
connectors and accessories to be installed on the housing, including HDMI, vacuum valve or
electronic strobe triggering bulkheads. For such accessories offered by Fantasea, please visit the
Fantasea website –www.fantasea.com
To remove the M16 port cover insert a coin into the dedicated slot featured on the cover and turn
the cover counterclockwise until it can be safely removed. Store the cover for possible future use.
Follow the instructions provided with the selected accessory product in order to install it inside the
housing.
Important Notice! Once the M16 port cover has been removed and replaced, it important to carry
out the first dive with the housing empty (no camera installed inside) in order to verify that the
housing watertight seal has not been affected during the replacement.
10.Double Fiber Optic Cable Port –The 2 fiber optic cable ports with the inserted adaptors allow for
easy attachment of up to 2 fiber optic cables to the housing. For further instructions, please refer to
the section “Underwater Flashes & Strobes” in this manual.
Note that the FA6000 Housing blocks the output of the built-in flash and prevents it from being
visible in images captured. This ensures that only the external strobes connected to the system
illuminate the subject, thereby diminishing the effects of backscatter, as well as shadowing caused by
housing lens port and lens accessories mounted on the housing.
11.Lens Dial –When a zoom lens is installed on the camera and a compatible lens gear is installed on
the lens, turning this dial rotates the lens ring. For proper and smooth operation, it is recommended
to install a Fantasea lens gear on the lens. For further instructions regarding installation of the lens
gear, please refer to the instruction manual provided with your lens gear and/or lens port. For lens
ports and lens gears compatible with your housing, please visit the Fantasea website –
www.fantasea.com
12.Interchangeable Lens Port System –The housing features an FML interchangeable lens port system,
which allows using a wide range of lenses underwater. The housing is compatible with any FML lens
port, as well as other lens ports available in the market. For compatibility information, please visit the
FA6000 Housing page on the Fantasea website –www.fantasea.com
For further instructions regarding lens ports installation and removal please refer to the section
“Installing and Removing Lens Ports”.

FA6000 Housing Instruction Manual 20190204
9
13.Lanyard Loops –The 3 lanyard loops featured on the housing (one loop at the bottom of the axis side
of the housing and two top and bottom loops at the opposite side of the housing) are used to attach
a Hand Lanyard or Hand Strap to the housing, as well as to secure accessories using snap cords or
secure strings.
14.Latch Dial Lock –Ensures the secure dial doesn’t accidently open during the dive. For further
instructions, please refer to the sections "Opening the Housing” and “Closing the Housing”.
15.Latch Dial –When locked fully into place, this dial ensures the housing is properly closed and
watertight sealed. For further instructions, please refer to the sections "Opening the Housing” and
“Closing the Housing”.
Housing View #2 –Front - Corresponding numbered descriptions are listed on the following page
16.Lens Port Lock
18.Lens Release Control
17.Tripod Mounting Screw Holes
(bottom of housing)

FA6000 Housing Instruction Manual 20190204
10
16.Lens Port Lock –When set to the “lock” position, the Lens Port Lock ensures that the fully closed lens
port doesn’t accidently open during the dive. When set to the “unlocked” position, the lens port can
be removed and replaced. For further instructions regarding lens ports installation and removal
please refer to the section “Installing and Removing Lens Ports”.
Important Notice! The Lens Port Lock must not serve as an indication of a proper watertight seal and
does not ensure that the lens port was properly installed on the housing. For lens port installation
guidelines and double check procedures, please refer to the section “Installing and Removing Lens
Ports”.
17.Tripod Mounting Screw Holes –Enable mounting the housing on a tray or tray & handle system,
thereby allowing for the addition of various image enhancement accessories. The 3 adjustment screw
holes provide flexibility with respect to the choice of tray and the position of the housing mounted on
it. This configuration also allows for the use of 2 set screws for the tray mount, thereby preventing
any swiveling of the housing on the tray.
18.Lens Release Control –Pushing this control presses the camera Lens Release button, which allows for
unscrewing a lens and removing it from the camera while the camera is accommodated inside the
housing. This is especially useful when using exceptionally large lenses which cannot be installed on
the camera prior to inserting it into the housing. In such cases, the lens should be installed and
removed through the lens port. For further instructions please refer to the section “Installing the
Camera”.

FA6000 Housing Instruction Manual 20190204
11
Housing View #3 –Rear - Corresponding numbered descriptions are found below the image
19.Flash Pop-Up –Pushing this control pops-up the camera built-in flash.
Note that once the camera built-in flash has been popped up, it can be pushed back into the camera
body and disabled using the Flash Push-Down control.
20.Menu –Pushing this control activates the camera menu button.
21.Non-Functional Lever –Rotating this lever does not activate any of the camera controls. It also
doesn’t interfere with proper housing operation. Therefore, this lever can be ignored while using the
housing.
19.Flash Pop-Up
29.C2 Button /
Delete
27.Control Wheel
32.Drive Mode /
Self Timer /
Left
31.Center Button
30. Playback
33.Removable
Anti-Glare
Hood
20.Menu
21.Non-Functional Lever
22.AEL Control /
Enlarge
24.Movie Recording
23.Fn (Function)
25.Display / Up
26.ISO / Right
28.Exposure
Compensation /
Image Index /
Photo Creativity /
Down

FA6000 Housing Instruction Manual 20190204
12
22.AEL Control / Enlarge –Pushing this control activates the camera AEL Button / Enlarge Button.
In shooting mode, push this control to activate the AEL button, which locks exposure while
composing an image.
In Playback mode, push this control to enlarge the reviewed image.
23.Fn (Function) - Pushing this control activates the camera Fn (Function) button.
In shooting mode, pushing this control allows recalling registered functions.
a. Push the Function control.
b. Select the desired function by pushing the up/down/left/right sides of the control wheel.
c. Select the setting value by turning the control wheel.
d. Some functions can be fine-tuned using the control dial.
e. Push the center button to confirm the selection.
f. To adjust settings from the dedicated settings screen, select the desired function (step b),
push the center button and adjust settings on the dedicated settings screen.
In playback mode, push this control to send the reviewed image to a smartphone.
24.Movie Recording –Pushing this control activates the camera Movie button and starts/stops
recording a video.
25.Display / Up - Pushing this control activates the camera Display / Up button.
26.ISO / Right - Pushing this control activates the camera ISO / Right button.
27.Control Wheel - Rotating this wheel operates the camera control wheel, thereby enabling to alter
exposure values, navigate through menus and other functions assigned to the control wheel.
28.Exposure Compensation / Image Index / Photo Creativity / Down –Pushing this control activates
the camera Exposure Compensation / Image Index / Photo Creativity / Down button.
29.C2 Button / Delete –
In shooting mode, push this control to activate the C2 button. Various functions can be assigned to
this button through the camera menu, providing access to favorite and most frequently used
settings, thereby allowing quick operation based on your personal preferences and shooting habits.
In playback mode, push this control to delete images.
30.Playback –Pushing this control allows entering the playback mode and reviewing images or videos
stored on the memory card.
31.Center Button - Pushing this control activates the camera center button, which is mainly used to
confirm selections.
32.Drive Mode / Self Timer / Left –Pushing this control activates the camera drive mode / self timer /
left button.

FA6000 Housing Instruction Manual 20190204
13
33.Removable Anti-Glare Hood –The anti-glare hood enables a better view of the LCD screen when
shooting in bright conditions. It can be removed and installed during the dive. For further
instructions, please refer to the section “Preparing the Housing”.
Housing View #3 –Front Door Interior - Corresponding numbered descriptions are found on the
following page
34. Moisture Detector
Alarm Unit
36. Moisture Sensor Unit
(under camera tray)
35. Camera Tray
38. Lens Port Lock
Interior View
39. LED Trigger Ports
37. Camera Tray Port

FA6000 Housing Instruction Manual 20190204
14
34.Moisture Detector Alarm Unit –The moisture detector preinstalled in the housing alerts of a
possible leak whenever moisture is detected by the sensor. The alarm unit of the Moisture Detector
is installed inside the housing, opposite the latch dial. For further information and instructions, please
refer to the section “Fantasea Moisture Detector”.
35.Camera Tray –The tray allows for easy installation of the camera inside the housing and ensures the
camera is positioned securely and steadily during the dive.
Note that the camera battery compartment can be opened when the camera is installed on the tray,
allowing for easy and quick battery and memory card replacement without having to remove the
camera from the tray
For further instructions, please refer to the section “Installing the Camera”.
36.Moisture Sensor Unit –The Moisture Sensor unit is installed just under the camera tray. It is
connected with a thin wire to the moisture detector alarm unit. For further information and
instructions, please refer to the section “Fantasea Moisture Detector”.
37.Camera Tray Port –Secures the camera tray and ensures the camera is positioned firmly and tightly
inside the housing, allowing for smooth operation in all depths.
For further instructions, please refer to the section “Installing the Camera”.
38.Lens Port Lock (Internal View) –After a lens port has been installed and the lens port lock has been
locked, it is recommended to examine the lock inside the housing to confirm that the port has been
properly installed and the port lock has been completely locked. For further instructions, please refer
to the section “Installing and Removing Lens Ports”.
39.LED Trigger Ports –Designed to allow the use of an LED Flash Trigger inside the housing. The LED
Flash Trigger is a useful accessory when making use of slave strobes connected to the housing with
fiber optic cables. It attaches to the camera hot-shoe on one end and to the two LED Trigger Ports on
the other end. When an image is captured, the device LEDs installed inside the LED Trigger Ports
trigger the slave strobe without activating the camera built-in flash. This spares camera battery
consumption and also prevents the built-in flash recycle time from limiting continuous shooting. For
LED Trigger Ports available, please visit the Fantasea website –www.fantasea.com

FA6000 Housing Instruction Manual 20190204
15
SONY A6000 MIRRORLESS DIGITAL CAMERA
The Sony a6000 is an APS-C interchangeable lens
camera which features superb 24MP quality,
quick autofocus and a very portable design. Add
an OLED Tru-Finder™, manual controls and a
range of lenses for a superior alternative to bulky
DSLRs. The a6000’s Fast Hybrid AF combines the
strengths of both phase and contrast-detection
autofocus. With a class-leading 179 phase
detection points (covering almost the entire
image) and a high-speed contrast-detection function, the result is not only an impressive 11 fps burst
mode, but also highly accurate movement tracking for both stills and video.
“We've not before seen a camera at this price able shoot so fast and track focus so well, nor one that
offers such complete control over its movie shooting. And, for that matter, it's not just a step forward for
mirrorless cameras: we'd struggle to think of another camera in this price bracket that offers so much in
the way of stills and video capability in such a coherent package.” (dpreview.com)
Sony a6000 Highlights
24.3-megapixel Exmor CMOS (23.5 x 15.6 mm) sensor for outstanding light sensitivity
Interchangeable lens system
Fast Hybrid AF with 179 AF points
BIONZ X™ image processing engine for superior detail reproduction
Full HD movie recording (up to 60p)
11 FPS continuous shooting
Lock-on AF for maintaining focus on a moving subject automatically
Eye EF to ensure faces are always accurately focused
High resolution OLED Tru-Finder offering 100% frame coverage
Customizable buttons for shooting in greater speed and convenience
Customizable UI (user interface) enables smooth and personalized operation
Tiltable 3-inch LCD screen
One-touch remote and one-touch sharing

FA6000 Housing Instruction Manual 20190204
16
SETTING UP THE HOUSING
PREPARING THE CAMERA
1. Install a (preferably empty) memory card (32 GB+ capacity recommended) and a fully charged
battery inside the camera.
2. Remove the camera strap from the camera if one was installed.
3. Note that there is no need to remove the eyepiece rubber cup, as it doesn’t interfere with
installation or operation of camera inside the housing.
4. Install the selected lens on the camera and remove the lens cap from lens.
5. If making use of a lens gear and/or light shading pad, install them on the lens following the
instructions provided with these accessories.
6. Built-in Flash Push Down Reminder Sticker –Prior
to installing the camera inside the housing, the
camera built-in flash must be pushed into the
camera body. Any attempt of installing the
camera into the housing with the flash popped-
up might damage the camera and the housing
and will necessarily interfere with a proper
watertight seal of the housing. A dedicated warning sticker was designed for the purpose of
reminding you to push the built-in flash into the camera body prior to installing it into the
housing. It is recommended to attach this sticker on the camera, at the back of the popped–up
built-in flash (image #1).
7. Monitor/Finder setting - The a6000 camera is equipped with a sensor which is capable of
automatically switching the display between the electronic viewfinder and the LCD monitor.
Default camera settings activate this sensor and enable the automatic switch. In order to ensure
that the LCD monitor doesn’t turn off automatically underwater, it is important to set the
Monitor/Finder setting to Monitor (Manual) prior to installing the camera inside the housing.
This should be done through the settings menu of the camera.
IMPORTANT
NOTICE
It is important that a first dive is always carried out with the housing
empty (no camera installed inside) in order to verify that the housing
watertight seal has not been affected during lens port installation, M16
port accessories installation, transport or long periods of storage.
Attach the
sticker here
Image #1

FA6000 Housing Instruction Manual 20190204
17
8. It is also recommended to program the camera to the most frequently used settings prior to
installing the camera in the housing. Such optional settings include assigning functions to custom
buttons (C1 and C2) and customizing menu items to include most frequently used items.
WHEN USING THE HOUSING FOR THE FIRST TIME
1. Peel the transparent plastic screen protector
off the back door exterior of the housing.
2. Install the hand lanyard on the housing by
inserting it through the lanyard loop on the
bottom right of the housing (facing from back),
then pulling it through itself and testing it in
order to make sure it is secure (image #2).
3. Open the housing (see section “Opening the
Housing”) and remove the anti-glare hood out
of the housing. Secure the anti-glare hood to
the housing by tying its secure string around the lanyard loop at the bottom left side of the
housing. Install the anti-glare hood over the anti-glare hood rails at the back of the housing. First
install the anti-glare hood over the top rail (image #3) and then gently and carefully stretch it
downwards to install it on the bottom rail, making sure it’s sitting securely on both upper and
lower rails (image #4).
4. Installing the Extended Shutter Trigger –When mounting the housing on a tray & handle or tray
& arm system, you might consider replacing the shutter release trigger with the extended
replacement trigger included in the package. The extended trigger provides easier access to the
shutter release when an arm or handle are mounted next to the housing. To replace the shutter
release trigger with the extended one included, complete the following steps:
a. Place the housing on a protected surface.
b. Identify the Extended Shutter Release Kit (image #5).
Image #2
Image #3
Image #4

FA6000 Housing Instruction Manual 20190204
18
c. Using the screwdriver included in the kit, remove the screw that secures the shutter
release trigger (image #6). Store it safely, although a spare screw is included in the kit.
d. Remove the trigger by pulling it out and away from the housing (image #7). Note that
once the trigger has been removed, the control metal shaft can be accidently pushed
in, resulting with the spring in the interior of the control slightly moving out of place
and thus disabling proper operation of the control. Therefore, make sure not to push
the control shaft into the housing. Store the removed trigger for possible future use.
e. Install the replacement extended trigger on the exposed metal shaft of the control by
aligning the protrusion featured on the control with the shape of the shaft (image #8).
f. Using your finger, apply slight counterforce on the control inside the housing to prevent
the shaft from being pushed into the housing while installing the replacement extended
trigger.
g. Using the screwdriver, install the screw in order to secure the replacement extended
trigger in place (image #9 on the following page).
Image #5
Image #6
Image #7
Image #7
Image #8

FA6000 Housing Instruction Manual 20190204
19
h. Install the camera inside the housing (see
section “Install the Camera”) and test the
housing shutter release control to ensure
it properly activates the camera shutter
release button.
i. Note that if encountering problems with
operation of the control upon completing
the replacement, the spring featured on
the interior of the control might have
accidently moved out of place. This being
the case, remove the shutter release
trigger again, gently push the metal shaft
of the control towards the housing,
rearrange the spring inside the housing so
it sits entirely below the black plastic lever
of the control (image #10), push the
control metal shaft back out and reinstall
the trigger.
INSTALLING M16 PORT ACCESSORIES
The port above the housing axis features a standard M16 thread hole and allows for optional
connectors and accessories to be installed on the housing, including HDMI, vacuum valve or
electronic strobe triggering bulkheads. For such accessories offered by Fantasea, please visit the
Fantasea website –www.fantasea.com
1. To remove the M16 port cover insert a coin into the dedicated slot featured on the cover and
turn the cover counterclockwise until it can be safely removed (images #11 and 12).
Image #9
Image #10
Image #11
Image #12

FA6000 Housing Instruction Manual 20190204
20
2. Store the cover for possible future use.
3. Follow the instructions provided with the selected accessory product in order to install it
inside the housing and make sure the M16 port accessory installed consists of an O-ring for
maintaining the watertight seal of the housing.
MOUNTING AND REMOVING LENS PORTS
The housing features an FML interchangeable lens port system, which allows using a wide range of
lenses underwater. The housing is compatible with any FML lens port, as well as other lens ports
available in the market. For compatibility information and lens ports available, please visit the Fantasea
website –www.fantasea.com
1. Mounting a lens port on the housing:
a. If possible, it is recommended to mount the lens port on the housing prior to
installing the camera inside. If using exceptionally large lenses which cannot be
installed on the camera prior to inserting it into the housing, the camera and lens can
be installed inside the housing prior to mounting the lens port. Please refer to section
“Installing the Camera” - step 18.
b. For smooth installation and
removal of the lens port, it is
recommended to apply a slight
amount of silicone grease over
the lens port O-ring prior to
installing it on the housing.
c. Place the housing on a
protected surface.
d. Turn the lens port lock
rightwards, so it’s seated at the
“UNLOCK” position (image
#13).
Important
Note
Once an accessory has been installed using the M16 port, it important to
carry out the first dive with the housing empty (no camera installed
inside) in order to verify that the housing watertight seal has not been
affected during the replacement
Image #13