Fantasea Line FG7X II A VACUUM User manual

FG7X II A VACUUM Housing Instruction Manual 20191218
Fantasea Line
FG7X II A VACUUM Housing
(Cat. No. 1361)
for Canon G7 X Mark II
Instruction Manual

FG7X II A VACUUM Housing Instruction Manual 20191218
2
TABLE OF CONTENTS
TABLE OF CONTENTS................................................................................................................................ 2
DISCLAIMER............................................................................................................................................. 3
INTRODUCTION ....................................................................................................................................... 3
GENERAL INFORMATION........................................................................................................................................ 3
FEATURES &SPECIFICATIONS.................................................................................................................................. 4
INCLUDED IN PACKAGE............................................................................................................................ 5
IDENTIFICATION OF HOUSING PARTS....................................................................................................... 7
SETTING UP THE HOUSING..................................................................................................................... 13
PREPARING THE CAMERA..................................................................................................................................... 13
PREPARING THE HOUSING ................................................................................................................................... 13
OPENING THE HOUSING...................................................................................................................................... 15
CHECKING THE O-RING ....................................................................................................................................... 16
INSTALLING THE CAMERA .................................................................................................................................... 17
CLOSING THE HOUSING....................................................................................................................................... 18
REMOVING THE CAMERA FROM THE HOUSING ....................................................................................................... 20
USING THE CAMERA BUILT-IN FLASH ..................................................................................................................... 20
FANTASEA HYBRID VACUUM SAFETY SYSTEM ........................................................................................ 22
OPTIONAL ACCESSORIES........................................................................................................................ 30
EXTERNAL FLASHES............................................................................................................................................. 30
FLASH &VIDEO LIGHTING SETS............................................................................................................................. 32
LENS ACCESSORIES ............................................................................................................................................. 32
CARE & MAINTENANCE.......................................................................................................................... 33
FANTASEA PRODUCT CONSUMER LIMITED WARRANTY.......................................................................... 34

FG7X II A VACUUM Housing Instruction Manual 20191218
3
DISCLAIMER
While every effort has been made in order to ensure that the information included in this instruction
manual is accurate and complete, no liability will be accepted for any errors or omissions. Fantasea Line
reserves the right to change product specifications and features described herein at any time without prior
notice. No part of this instruction manual may be copied, translated or reproduced without the prior
written permission of Fantasea Line. Fantasea Line makes no warranties aside from limited product
warranty as described at the end of this manual.
INTRODUCTION
General Information
The FG7X II A VACUUM Housing features a stylish and ergonomic design, specifically created for the Canon
G7 X Mark II digital camera. The FG7X II A VACUUM Housing is manufactured to the highest professional
standards of function, style and durability. It is depth rated to 60m/200 feet and features ergonomically
designed and labeled controls. The Fantasea FG7X II A VACUUM is the ultimate waterproof home for the
Canon G7 X Mark II.
The FG7X II A VACUUM Housing is ideal for outdoor and underwater photography. Underwater
photographers can dive or snorkel and capture all the excitement of this fascinating world, while outdoor
photographers also have the option of capturing the action of outdoor and water sports activities, such as
paddle sports, sailing, boating, surfing, fishing, hunting, backpacking and camping. The FG7X II A VACUUM
Housing is shock resistant and protects the camera from water, sand, dust, frost, impact, as well as other
damaging elements and harmful occurrences. The FG7X II A VACUUM Housing was designed to be
compatible with a complete accessory system, enabling photographers to enhance the quality of their
images.
Note
Please read this manual carefully in order to properly operate the FG7X II A
VACUUM Housing. Store this manual in a safe place for further reference once
you have read it.

FG7X II A VACUUM Housing Instruction Manual 20191218
4
Features & Specifications
Hybrid Vacuum Safety System included
Moisture detector and alarm
Depth rated to 60m/200 feet
Ergonomic design
Made from durable injection molded Polycarbonate
Full access to all essential camera controls & functions with clearly marked controls
Shock resistant
Double O-ring seal
Special mount for lighting accessories
Removable double fiber optic cable connection
Removable flash diffuser
Easy and secure installation of camera
Removable anti-glare hood for the LCD screen
Port Cover
Dedicated video control button for easy video filming in any shooting mode
Compatible with a wide range of underwater photo accessories
Weight (with camera on land): 1,134g
Weight (without camera on land): 830g
Dimensions (without accessories): 16.5 x 14.5 x 13 cm \ 6.5 x 5.7 x 5.1 inch (W x D x H)
Manufacturer's warranty included

FG7X II A VACUUM Housing Instruction Manual 20191218
5
INCLUDED IN PACKAGE
1. FG7X II A VACUUM Housing
2. Removable flash diffuser with secure line
3. Hand lanyard
4. Silicone grease
5. Anti-glare hood for LCD screen
6. M16 port cap for Vacuum Valve
(if valve is removed)
7. Screwdriver
8. Silica gel packs
9. O-ring remover
10.Spare back door O-ring seal
11.Diffuser quick release secure string
(housing side)
12.Lens Port Cover
1
5
7
2
8
9
3
4
10
11
Camera not included
6
12

FG7X II A VACUUM Housing Instruction Manual 20191218
6
Hybrid Vacuum Safety System Components
13.Vacuum pump
14.Rubber fitting for pump
15.Wrench
16.Double-sided stickers
14
13
15
16

FG7X II A VACUUM Housing Instruction Manual 20191218
7
IDENTIFICATION OF HOUSING PARTS
Top of Housing - Corresponding numbered descriptions are found on the following page
Note
1. Please refer to the Canon G7 X Mark II camera instruction manual for
detailed descriptions and instructions regarding all camera controls and
functions.
2. It is strongly recommended that you familiarize yourself with all the
controls topside before using these controls underwater.
1. Zoom Control
2. Shutter Release
3. On/Off
4. Mode Dial
6. Cold Shoe Mount
5. Exposure
Compensation
Dial

FG7X II A VACUUM Housing Instruction Manual 20191218
8
Numbered descriptions below refer to corresponding numbers on the top housing graphic (previous page):
1. Zoom Control –Turning this control activates the camera zoom button.
a. In Shooting Mode –
i. Turn the zoom control clockwise to zoom out, increasing the area visible in the frame.
ii. Turn the zoom control counterclockwise to zoom in, so that the subject fills a larger
area of the frame and for close-up and macro images to be taken.
b. In Playback Mode - use the zoom control as an index or playback lever.
2. Shutter Release –Activates the camera shutter release button and auto focus prior to taking the
picture.
3. On/Off - Pushing this control activates the camera power switch button and turns the camera on/off.
4. Mode Dial –Turn this dial to change shooting modes.
Important Notice! It is recommended to align housing and camera mode dials prior to installing the
camera inside the housing. Please refer to the section “Installing the Camera” for more information.
5. Exposure Compensation Dial - Rotating this knob operates the camera’s Exposure Compensation Dial
to the opposite direction.
a. In order to set a higher exposure compensation value, rotate the exposure compensation dial
clockwise.
b. In order to set a lower exposure compensation value, rotate the exposure compensation dial
counterclockwise.
6. Cold-Shoe Mount for Lighting Accessories- Enables mounting a flash, video light, torch or focus light
on top of the housing by using a dedicated connector. For further information regarding such
connectors, please visit the Fantasea website –www.fantasea.com

FG7X II A VACUUM Housing Instruction Manual 20191218
9
Front Side of Housing - Corresponding numbered descriptions are found below the image
7. Fiber Optic Cable Plate-
a. When installed on the housing, the fiber optic cable plate and the two adaptors inserted
inside it allow for an easy attachment of 2 fiber optic cables to the housing. For further
instructions, please refer to the section “External Flashes”.
b. Remove the fiber optic cable plate from the housing in order to make use of the internal
camera flash during your dive. In order to remove the plate, insert your fingers beneath the
adaptors installed inside the plate and pull the plate upwards till it is removed from its slot.
Note that when photographing using the camera built-in flash only, the flash diffuser
accessory should be installed, or else unwanted shading will occur in most images taken.
c. Make sure the fiber optic cable plate is secured to the housing by its secure line in order to
avoid losing it during the dive.
d. If using only one external flash, make sure the second fiber optic cable adaptor remains in its
place to block any light coming out of the exposed adaptor hole.
11.Tripod Mounting Screw Holes
(bottom)
7. Fiber Optic
Cable Plate
9. Control Ring
10.Lens Port
12. Lanyard Loop
8. Flash Up Switch
(on side)

FG7X II A VACUUM Housing Instruction Manual 20191218
10
8. Flash Up Switch - Rotating this control clockwise (pulling it towards the back of the housing) will pop-
up the camera built-in flash. Note that once the camera built-in flash has been popped up, it can be
disabled again using the Flash / Right control and selecting “flash disabled” on the flash mode menu.
Rotating the Flash Up Switch counterclockwise will not have any effect on the built-in flash.
9. Control Ring –Rotating this knob activates the function that you have assigned to the Control Ring.
Please refer to the camera instruction manual to assign a function to the Control Ring.
Important Notice! The preferred Control Ring function should be assigned on the camera prior to
inserting the camera into the housing, as in various shooting modes, Control Ring assignment might
not be accessible through the housing.
10.Lens Port- The housing lens port features a 67mm thread and it’s compatible with a wide variety of
“wet” accessory filters and lenses, including macro lenses, wide angle lenses and color correction
filters. In order to maintain the threads of the lens port, it is recommended to apply a small amount
of silicone grease to the threads on the housing port and on the accessory lens prior to installation.
For a selection of lens accessories available, visit the Fantasea website www.fantasea.com
11.Tripod Mounting Screw Holes –Enable mounting the housing on a tray, thereby allowing for the
addition of various image enhancement accessories to your underwater photo system. By choosing
any one of 3 adjustment positions, you can better determine how and where to position the housing
on the tray. This configuration also allows for the use of 2 set screws for the tray mount, thereby
preventing any swiveling of the housing on the tray.
12.Lanyard Loops –The 4 lanyard loops featured on the housing are used to attach a Hand Lanyard or
Hand Strap to the housing, as well as to secure accessories using snap cords or secure strings.
Important Notice
Screws longer than 7mm should not be screwed into the housing Tripod
Mounting Plate, as they might damage the plate and housing.