Farm King 1066 Product manual

OperatOr and parts Manual
112010
Conventional Auger
Model 1066 & 1076
SZ000252

3
Table of Contents - 1066 & 1076 Conventional Auger
Introduction .................................................................................................................................4
Safety ............................................................................................................................................5
• Safety ................................................................................................................................5
• General Safety ..................................................................................................................5
• Operation Safety ..............................................................................................................5
• Transport Safety ...............................................................................................................6
• Electrical Safety ................................................................................................................6
• Safe Operation Instructions ............................................................................................6
Assembly ......................................................................................................................................8
• 4 and 6 Bolt Hub Assembly ...........................................................................................10
• Head Drive Assembly ....................................................................................................10
• Assembly Instructions ................................................................................................... 11
• Assembly Instructions - PTO Drive ...............................................................................15
Parts ............................................................................................................................................16
• 1066 and 1076 Parts........................................................................................................16
• Decals ..............................................................................................................................21
• PTO Drive ........................................................................................................................22
• 6005 Gear Box ................................................................................................................23
Warranty ....................................................................................................................................24
Manufacturer’s statement: for technical reasons Buhler Trading Inc. reserves the right to modify
machinery design and specifications provided herein without any preliminary notice.
Information provided herein is of descriptive nature. Performance quality may depend on grain
type, grain moisture, auger elevation and other factors.
Table of Contents

4
Introduction
To the owner
Thank you for purchasing a Farm King 1066 or 1076 Conventional Auger.
Farm King Conventional Augers have been designed to provide many years of profitable and
dependable service. To assure maximum performance of your auger, it is mandatory that you
thoroughly study the operator’s manual and follow its recommendations. PLEASE EXAMINE
YOUR UNIT CLOSELY AND READ THE ASSEMBLY INSTRUCTIONS TO SEE THAT YOUR UNIT IS
PROPERLY ASSEMBLED. Proper operation and maintenance are essential for safety, to maintain
performance, and to maximize the life of the auger. When ordering parts or inquiring about the
auger, you must include the serial number which is located on the second upright of the lower
truss support.
It is the owner’s responsibility to:
Operate and maintain this auger in a safe manner and in accordance with all applicable local, state,
and federal codes and/or laws.
Make sure each and every operator has read the operator’s manual and thoroughly understands
safe and correct operating procedures.
Make sure unauthorized people do not operate or are not in the vicinity of the auger while it is in
operation.
Maintain the auger in accordance with the maintenance schedule in this manual. Furthermore, as
additional technology becomes available, the owner is responsible for improving the safety and
reliability of the system.
Fulfill all warranty obligations so as not to void the warranties. Verify the unit is warranty registered
prior to making any warranty claims. The warranty section at the back of this manual outlines the
warranty policy of Farm King.
Abuse or modifications to the auger that change the performance other than original factory
specifications void the warranty.
Farm King reserves the right to make product improvements to the equipment at any time. It shall
not be obligated to make such changes to machines already in service.
*The owner, manager and/or operator is responsible for safe, accurate operation and maintenance
of the Farm King 1066 or 1076 Conventional Auger.
Introduction - 1066 & 1076 Conventional Auger

5
Safety
Safety Instructions
An Operator‘s Manual is furnished with each grain auger. Additional or replacement manuals
are available. Do not operate the unit before reading and understanding the Operator‘s Manual.
Understand the operating procedures below to avoid personal injury or death.
The alert symbol is used throughout this manual. It indicates attention is required and identifies
hazards. Follow the recommended precautions.
The safety alert symbol means…
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
General Safety
An auger can collapse and fall on the operator or bystander causing serious injury or death.
Always support the discharge end when the following conditions occur:
• While unit is in operation.
• When dismounting the undercarriage.
The accidental tipping or upending of an auger may cause serious injury or death to the operator
or bystanders. When the grain flow is shut off to the auger an overbalance situation can occur,
suddenly raising the intake auger. Adequate anchorage of the intake end or support from bin is
required at all times, especially in the following conditions:
• While unit is in operation.
• When moving the auger.
• When raising or lowering the auger.
• Maximum elevation is determined by interference between track car and auger structure. The
operator must stop raising the auger before track car reaches the end of the track. Continued
lift will cause failure of the winch, lift cable or auger supports, causing auger to collapse,
which can result in serious injury or death.
Contact with rotating flighting will cause serious injury or death.
• Do not stand on the intake cage.
• Keep hands, feet and clothing away from the intake and discharge flighting.
Operation Safety
Intentional or accidental contact with moving parts may result in a serious injury or death. Observe
the following operating procedures.
• Keep all safety devices in place.
• Do not adjust, service, lubricate, clean, unclog or move the mechanism until all power is
shut off.
• Keep hands, feet and clothing away from moving parts while in operation.
• Keep off the equipment at all times.
• Make certain that everyone is clear of the equipment at all times.
• Make certain that everyone is clear of the equipment before applying power.
• Keep children, visitors and all untrained personnel away from machine while in operation
Safety - 1066 & 1076 Conventional Auger

6
Transport Safety
Care must be used when moving or transporting the auger. Accidental tipping or upending of an
auger can occur and may cause serious injury or death to the operator or bystanders.
• Never move the auger manually.
• Be sure auger is empty before attempting to move.
• Never push on the undercarriage of the auger.
• Tow the auger at slow speed and in the down position.
• Always test the intake end of the auger for downward weight when attaching or releasing.
• Never raise the hitchpoint higher than the vehicle‘s tow bar.
Electrical Safety
Contact with overhead wires may cause electrocution of the operator or bystanders. Contact with
overhead obstructions may cause collapse or tipping of the auger or may cause the overhead
obstruction to fall. In both cases the operator or bystander can be seriously injured or killed.
Observe the following:
• Tow the auger at slow speed and in the down position.
• Raise or lower the auger slowly.
Electrical malfunction can cause electrocution of the operator or bystanders.
Observe the following rules.
• Disconnect power and electrical driven units before resetting motor overloads.
• Do not operate electric motor equipped units until unit is properly grounded.
Safe Operating Instructions
There are several decals on the grain auger and its attachments with safety instructions.
Read and understand these safety alerts before operating.
The shielding has been removed in some of the illustrations for parts demonstration only.
Install all shields before operating the unit.
DANGER
Electrocution hazard. This machine is not insulated. Keep away
from overhead electric wires and devices. Electrocution can occur
without direct contact. Failure to keep away will result in serious
injury or death.
DANGER
Maximum elevation is determined by interference between track
car and auger structure. The operator must stop raising the auger
before track car reaches the end of track. Continued lift will cause
failure to the winch, lift cable or auger supports, causing auger to
collapse, resulting in serious injury or death.
Safety - 1066 & 1076 Conventional Auger

7
Safety - 1066 & 1076 Conventional Auger
DANGER
Upending hazard. 1 - Never mover the auger manually - use a
vehicle. 2 - Always have downward weight on the intake end of
the auger. 3 - Always test the downward weight before releasing
the auger from the vehicle or hold down. 4 - Always lift the intake
slowly and keep it no higher than the tractor tow bar when
attaching and releasing it. 5 - Never push on the undercarriage.
6 - Never move the auger, with grain, in the auger tube. 7 - Always
lower the auger to transport postion before moving. Failure to
follow these guidelines may cause upending, which may result in
serious injury or death.
Shear bolt failure indicates an overload on the auger.
To remedy the problem:
1. Reduce flow into the intake of the auger. Wet grain requires more power to operate the auger.
The flow must be reduced in wet grain to prevent plugging and/or shear bolt failure.
2. Make certain the auger is running at the correct speed. Run the tractor PTO at 540 RPM for the
correct flighting speed. Slowing the auger will allow it to overload and plug.
3. Check for foreign objects (sacks, cans, rags, etc.) in the tube. Objects may go part way up the
tube and wedge between the flights, blocking the grain flow.
ALERT
Do not operate the auger empty during the break-in period.
For the best results, do not full feed the intake for the first 500
bushels. After break-in, never run auger at slow idle when full
feeding the auger.

8
Assembly - 1066 & 1076 Conventional Auger
1066 Trussing
1076 Trussing

9
Assembly - 1066 & 1076 Conventional Auger
Keep all shields in place during operation.
NOTE: Use a 3/8" x 1-1/4" Grade 2 shear bolt.
Using other than a Grade 2 bolt may result in
damage to the drive components.
1066 Model
1076 Model

10
Assembly - 1066 & 1076 Conventional Auger
Keep all shields in place during operation.
4 and 6 Bolt Hub Assembly
Head Drive Assembly

11
Assembly - 1066 & 1076 Conventional Auger
Assembly Instructions
One must use extreme caution when assembling this auger. Lifting devices (i.e. loader tractor,
forklift, etc.) are required as well as various wrenches and tools. Assemble the auger on a flat
surface. Right, left, front and back refer to looking at the auger from the intake end.
1. Lay the top (Ref. #1) and bottom (Ref. #2) auger tubes flat with the center joint spaced two feet
apart.
2. Fasten the flighting assemblies with two fine thread nuts and bolt combinations (Ref. #5).
Fasten the flighting assemblies so that the lower assembly (Ref. #4) overlaps the upper
assembly (Ref. #3). For the 1076 model, the upper and center assemblies are already
connected, but the lower and center assemblies must be connected. Be sure that the lower
assembly (Ref. #4) overlaps the center assembly (Ref. #4A).
3. Be sure the top (Ref. #1) and the lower (Ref. #2) tubes are straight in line. Slide the tubes
together and connect at the flange ring using the 1/2" x 1-1/2" bolt, nut and lockwasher
combinations (Ref. #25). NOTE: Do not fully tighten the bolts in the flange ring connection
the first time. Work around the flange at least twice to gradually pull the connection together.
Fully tightening the bolts on one side will pull the auger tubes out of alignment. Be sure the
driveline couplers join when joining the tubes. Install the driveline shield splice (Ref. #45)
4. Clamp the intake cage (Ref. #90) to the lower tube using 3/8" x 1-1/4" bolt, nut and lockwasher
combinations (Ref. #93). Be sure to have 1/2" clearance between the flight core and the
bearing. NOTE: Thrust load must be carried at the top of the auger.
5. Mount the drop spout (Ref. #83) with
3/8" x 1-14" bolt, nut and lockwasher
combinations and one half clamp (Ref.
#84).
6. Attach stop flags (Ref. #120) to the stop flag
arms (Ref. #121) using the 3/16" x 3/4" bolt,
nut and lockwasher combinations (Ref.
#123). The lettering must face the auger
tube when the arms are parallel to the
tube. These flags will swing out when the
track car approaches the end of the track.
NOTE: The operator must stop raising the
auger when these swing out.
7. Add No. 90 gear lube until 1/2 full.
Gearbox is shipped dry from the factory.

12
Assembly - 1066 & 1076 Conventional Auger
8. Assemble the truss risers as shown to
the right, using two supports (Ref. #27),
one 3/8" x 1" bolt, nut and lockwasher
combination (Ref. #32), one cross brace
(Ref. #28) and two 3/8" x 1-1/4" bolt, nut
and lockwasher combinations (Ref. #26)
per riser.
9. Mount the truss riser assemblies as instructed below
1066 Model
Mount the first truss riser assembly on the flange ring using the 3/8" x 1" bolt, nut and
lockwasher combinations (Ref. #32). Mount the second and third truss riser assemblies on the
truss mounts located on the top tube using 3/8" x 1" bolt, nut and lockwasher combinations
(Ref. #32). Install the 3/16" dia. truss cables (Ref. #30) using two cable clamps (Ref. #31) and
one cable thimble (Ref. #31) on each upper cable end. Be sure to run the cable through the
truss riser assemblies as shown. Tighten the cables with the eyebolts on the lower cable ends
to keep the auger straight.
Mount the undertruss riser assembly on the truss mount located on the lower tube using 3/8"
x 1" bolt, nut and lockwasher combinations (Ref. #32). Install the 1/4" dia. truss cables (Ref. #29)
using two cable clamps (Ref. #31) and one cable thimble (Ref. #31) on each upper cable end.
Be sure to run the cable through the truss riser assembly as shown. Tighten the cables with
the eyebolts on the lower cable ends to keep the auger straight. NOTE: Do not over-tighten the
undertruss. Over tightening the undertruss will cause the auger to bow down when the auger
is raised.
1076 Model
Mount the three truss riser assemblies on the truss mounts located on the top tube using
3/8" x 1" bolt, nut and lockwasher combinations (Ref. #32). Install the top pair (T) of 1/4" dia.
truss cables (Ref. #30) using two cable clamps (Ref. #31) and one cable thimble (Ref. #31) on
the upper cable ends. Install the bottom pair (B) of 1/4" dia. truss cables (Ref. #30) using two
cable clamps (Ref. #31) and one cable thimble (Ref. #31) on the upper cable ends. Both pairs
of cables go over the center riser. Be sure to run the cable through the truss riser assembly as
shown. Tighten the cables with the eyebolts on the lower cable ends. Adjust both top truss "T"
and bottom truss "B" to hold the auger straight. This process is trial and error, and experience
with trusses is helpful.
Mount the undertruss riser assembly on the truss mount located on the lower tube using 3/8"
x 1" bolt, nut and lockwasher combinations (Ref. #32). Install the 1/4" dia. truss cables (Ref. #29)
using two cable clamps (Ref. #31) and one cable thimble (Ref. #31) on the upper cable ends.
Be sure to run the cable through the truss riser assembly as shown. Tighten the cables with
the eyebolts on the lower cable ends to keep the auger straight. NOTE: Do not over-tighten the
undertruss. Over tightening the undertruss will cause the auger to bow down when the auger
is raised.

13
Assembly - 1066 & 1076 Conventional Auger
10. Assemble the undercarriage
1066 Model
Remove track stop pin (Ref. #118) from the end of the track, install track car (Ref. #50) onto the
top end of the track, and then replace track stop pin prior to using the auger. Failure to do so
could cause the auger to collapse.
Attach the rear lift arms (Ref. #35L & #35R) to the track car using one 3/16" x 1-1/2" cotter pin
(Ref. #53) for each arm. Attach the front lift arms (Ref. #36 & #37) to the front undercarriage
mount using one 3/16" x 1-1/2" cotter pin (Ref. #53) for each arm.
Lift the auger tube and position the arms so that the pivot rod (Ref. #41) can be inserted into
the four arms as shown. Secure the piviot rod by inserting 1/4" x 2" cotter pins with 1" x 14 ga
bushings (Ref. #42).
Attach the axle (Ref. #34) to the front arms. Use four 1/2" x 1-1/2" bolt, nut and lockwasher
combinations (Ref. #40).
Secure the front and rear arms by inserting one 3/8" x 1" bolt, nut and lockwasher combination
(Ref. #39) into the cross bracing connecting the front arms together and the rear arms together.
Mount the long cross braces (Ref. #38) on the rear arms using the 3/8" x 1" bolt, nut and
lockwasher combinations.
Mount wheels (Ref. #43)
1076 Model
Remove track stop pin (Ref. #118) from the end of the track, install track car (Ref. #50) onto the
top end of the track, and then replace track stop pin prior to using the auger. Failure to do so
could cause the auger to collapse.
Attach the rear lift arms (Ref. #35L & #35R) to the track car using one 3/16" x 1-1/2" cotter pin
(Ref. #53) for each arm. Attach the front lift arms (Ref. #36 & #37) to the front undercarriage
mount using one 3/16" x 1-1/2" cotter pin (Ref. #53) for each arm.
Lift the auger tube and position the arms so that the pivot rod (Ref. #41) can be inserted into
the four arms as shown. Secure the pivot rod by inserting 3/8" x 1-3/4" bolt, nut and lockwasher
combinations with 1-1/4" x 14 ga. bushings (Ref. #42)
Attach the axle (Ref. #34) to the front arms by inserting the undercarriage spindle and hub (Ref.
#59) through the front arms and into the axle. Use two 1/2" x 3-1/2" bolt, nut and lockwasher
combinations (Ref. #58) to secure the spindle and hub to the axle.
Secure the front and rear arms by inserting one 3/8" x 1" bolt, nut and lockwasher combination
(Ref. #39) into the cross bracing connecting the front arms together and the rear arms together.
Mount the cross bars (Ref. #19 & 20) using 3/8" x 5" bolt, nut and lockwasher combinations
(Ref. #21). Mount the long cross braces (Ref. #38) to the front and rear arms using the 3/8" x
1" bolt, nut and lockwasher combinations (Ref. #39) and 3/8" x 1-1/2" bolt, nut and lockwasher
combination (Ref. #39A).
Mount wheels (Ref. #43)

14
Assembly - 1066 & 1076 Conventional Auger
11. Mount the winch (Ref. #49) using the 3/8" x 1" bolt, nut and lockwasher combinations (Ref. #48)
and thread the cable as instructed below.
Fasten the lift cable (Ref. #56) to the tube by the tube splice with a cable thimble and two cable
clamps (Ref. #55). Thread the cable around and through the top sheave in the track car, back
around and through the sheave by the tube splice, back around and through the lower sheave
in the track car and fasten to the winch. The cable must be threaded between the mounting
plate and the cross shaft as shown.
DANGER
Winch must be aligned with cable so that the cable does not stack
on one side of the drum. Do not allow the cable to become slack
on winch drum. The cable may recoil and slip over the side of the
drum. In either case, the cable will wind on drum spindle and
cause the winch or cable to fail, allowing auger to drop, which
may cause physical damage to the auger or may cause personal
injury.
12. Mount the Owner's Manual container tube (Ref. #141) to the winch mount as shown, using 1/4"
x 3/4" bolt, nut and lockwasher combinations and mounting straps (Ref. #142).
13. See separate assembly instructions on the following pages for the different drive packages.

15
Assembly - 1066 & 1076 Conventional Auger
Assembly Instructions - PTO Drive
1. Attach the Implement Input Driveline (IID) (Ref. #81) to the gear box with a 7/16" x 2-1/2" spiral
pin (Ref. #82).
2. Mount the gear box shield (Ref. #78) using 1/2" x 3/4" bolt and lockwasher (Ref. #77).
3. Install the Implement Input Driveline hanger (Ref. #85) to the mount on the side of the auger
tube using a 3/8" x 1" bolt, nut and lockwasher combination.
Gearbox is shipped dry from the factory.
Add No. 90 gear lube until 1/2 full.
NOTE: Use a 3/8" x 1-1/4" Grade 2 shear bolt
on the Implement Input Drive. Using other
than a Grade 2 bolt may result in damage to
the drive components.

16
Parts - 1066 & 1076 Conventional Auger
Parts List - 1066 and 1076 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
76
1 SZ2937033 Auger Tube (Top Half) w/ Head & Bearing Brackets 1
SZ103640 Auger Tube (Top Half) w/ Head & Bearing Brackets* 1
SZ2937040 Auger Tube (Top Half) w/ Head & Bearing Brackets 1
SZ103618 Auger Tube (Top Half) w/ Head & Bearing Brackets* 1
2 SZ2938033 Auger Tube (Lower Half) w/ Brackets 1
SZ103641 Auger Tube (Lower Half) w/ Brackets* 1
SZ2938035 Auger Tube (Lower Half) w/ Brackets 1
SZ103619 Auger Tube (Lower Half) w/ Brackets* 1
3 SZ6607033 Flighting Assembly (Top Half) 1
SZ6607027 Flighting Assembly (Top Half) 1
4A SZ2667013 Flighting Assembly (Center Section) 1
4 SZ6608033 Flighting Assembly (Lower Half) 1
SZ6608035 Flighting Assembly (Lower Half) 1
5 SZ126104 BLT HHCS 1/2-20UNF 3G5 2 4
SZ125033 Nut LCK 1/2-20UNF 2 4
6 SZ5127240 Top Driveline Section w/ Couplers, 240" Long
(Under Shield)
1 1
7 SZ5128241 Lower Driveline Section, 240" Long (Under Shield) 1 1
8 SZ5127148 Top Driveline Section, 147-1/2" Long (Under Shield) 1
SZ5127235 Top Driveline Section, 234-1/2" Long (Under Shield) 1
9 SZ5128095 Lower Driveline Section, 95" Long (Under Shield) 1
SZ5128127 Lower Driveline Section, 127" Long (Under Shield) 1
10 SZ0431005 Flighting Extension, Head Drive 1 1
12 SZ4127005 Driveline Extension, Head Drive 1 1
13 SZ4937106 Sprocket Coupler w/ 7/16" Hole (Gear Box - Driveline) 2 2
14 SZ00436142 No. 60 Double Chain - 14 Pitch for Coupler 1 1
15 SZ6007017 7/16" x 1-3/4" Spiral Expand Pin 2 2
19 SZ0211028 32" Cross Bar 1
20 SZ0211050 50" Cross Bar 1
21 SZ126083 BLT HHCS 3/8-16UNC 5G5 4
SZ127009 WSHR LCK 3/8 4
SZ125007 Nut Hex 3/8-16 UNC 4
22 SZ0938687 Clevis Tow Hitch 1 1
23 SZ128008 1/2" x 2-3/4" Clevis Pin 1 1
SZ128018 No. 4 Hair Pin Cotter 1 1
24 SZ2016121 Wood Intake Bearing 1 1
25 SZ126092 BLT HHCS 1/2-13UNC 1-1/4 16 16
SZ125010 Nut Hex 1/2-13UNC G5 16 16
*Galvanized

17
Parts - 1066 & 1076 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
76
SZ127012 WSHR LCK 1/2 16 16
26 SZ126067 BLT HHCS 3/8-16UNC 1-1/4 8 8
SZ127009 WSHR LCK 3/8 8 8
SZ125007 Nut Hex 3/8-16UNC 8 8
27 SZ2038351 Cable Truss Support 8 8
28 SZ2031360 Truss Cross Brace 4 4
29 SZ2038322 1/4" Truss Cable w/ Eye Bolt 2 2
30 SZ2038365 3/16" Truss Cable w/ Eye Bolt 2
SZ2038438 1/4" Truss Cable w/ Eye Bolt 4
31 SZ6003161 3/16" Cable Thimble 2
SZ6003316 3/16" Cable Clamp 4
SZ6009104 1/4" Cable Thimble 2 4
SZ6003104 1/4" Cable Clamp 4 12
32 SZ6003801 3/8" x 1" Bolt, Nut & Lockwasher 12 12
34 SZ102948 Undercarriage Axle w/ 4 Bolt Spindle (114" Track) 1
SZ0211105 Undercarriage Axle w/ Removable 6 Bolt Spindle
(114" Track) 1
35R SZ0318254 Undercarriage Lift Arm (254"), Right 1
SZ0318252 Undercarriage Lift Arm (252"), Right 1
35L SZ0319254 Undercarriage Lift Arm (254"), Left 1
SZ0319252 Undercarriage Lift Arm (252"), Left 1
36 SZ0315195 Undercarriage Lower Arm (195"), Right 1
SZ03152281 Undercarriage Lower Arm (228"), Right 1
37 SZ0317195 Undercarriage Lower Arm (195"), Left 1
SZ03172281 Undercarriage Lower Arm (228"), Left 1
38 SZ0217410 Undercarriage Cross Brace 2
SZ0218410 Undercarriage Cross Brace 6
39A SZ126068 BLT HHCS 3/8-16 UNC 1-1/2 3
SZ125007 3/8" Hex Nut 16 UNC 3
SZ127009 3/8" Lockwasher 3
SZ127002 3/8" Flat Washer 3
39 SZ126065 BLT HHCS 3/8-16UNC 1 G5 6 8
SZ127009 3/8" Lockwasher 6 8
SZ125007 3/8" Hex Nut 16 UNC 6 8
40 SZ126092 BLT HHCS 1/2-13 UNC 1-1/2 4
SZ125010 Nut Hex 1/2-13UNC G5 4
SZ127012 WSHR LCK 1/2 4
41 SZ0311489 Undercarriage Pivot Rod (89-1/2") 1
SZ0218416 Undercarriage Pivot Rod (83-1/2") 1

18
Parts - 1066 & 1076 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
76
42 SZ6001403 1/4" x 2" Cotter Pin w/ 1" x 14 ga Bushing 2
SZ6003876 3/8" x 1-3/4" Bolt, Nut & Lockwasher w/1-1 /4" x 14
Ga. Bushing 2
43 SZ0114415 15" 4 Bolt Wheel 2
SZ0116615 15" 6 Bolt Wheel 2
44 SZ1630392 392" Top Driveline Shield 1
SZ1630479 479" Top Driveline Shield 1
45 SZ1629310 Shield Splice 1 1
47 SZ6003115 3/16" x 1-1/4" Driveline Shield Mount Screw 28 32
48 SZ126065 BLT HHCS 3/8-16UNC 1 G5 3 3
SZ127009 3/8" Lockwasher 3 3
SZ125007 3/8" Hex Nut 16 UNC 3 3
49 SZ2038221 Bolt-On Winch Assembly 1 1
50 SZ0211147 Track Car w/ 4 Rollers & 2 Sheaves 1
SZ0218147 Track Car w/4 Rollers & 2 Sheaves 1
53 SZ6003615 3/16" x 1-1/2" Cotter Pin 4 4
55 SZ6003104 1/4" Cable Clamp 2 2
56 SZ0212505 1/4" Aircraft Cable, 105' 1
SZ0212518 1/4" Aircraft Cable, 112' 1
58 SZ126098 BLT HHCS 1/2-13 UNC 3-1/2 G8 2
SZ127012 1/2" Lock Washer 2
SZ125010 1/2" Hex Nut 13 UNC G5 2
59 SZ0211115 6 Bolt Hub & Spindle Assembly (Removable) 2
60 SZ2018043 1-1/4" Bearing Driveline & Flight (Head Drive) 3 3
60A SZ201150 1-1/2" Bearing (Flight Inner Bearing) 1 1
61 SZ126063 BLT HHCS 3/8-16UNC 3/4 9 9
SZ127009 WSHR LCK 3/8 9 9
SZ125007 Nut Hex 3/8-16UNC 9 9
61A SZ126088 1/2" x 3/4" Bolt 4 4
SZ125010 1/2" Nut 4 4
SZ127012 1/2" Lockwasher 4 4
62 SZ65062MSCI000 Flange Housing for 8043 Bearing 6 6
62A SZ65080MSCI000 Flange Housing for 1500 Bearing 2 2
63 SZ0048017 No. 80-17 Tooth Sprocket (Driveline) 1 1
64 SZ0048022 No. 80-22 Tooth Sprocket (Flighting) 1 1
65 SZ6007025 7/16" x 2-1/2" Spiral Expand Pin 2 2
66 SZ0231141 1-1/4" x 14 ga Machine Bushing 4 4
67 SZ00438036 No. 80 Chain, 36 Pitch 1 1
68 SZ8481722 Head Drive - Face Plate 1 1
*As needed

19
Parts - 1066 & 1076 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
76
69 SZ8481808 Head Drive - Cover 1 1
70 SZ126051 BLT HHCS 5/16-18UNC 1-1/2 G5 1 1
SZ127010 WSHR LCK 5/16 1 1
SZ125006 5/16" Hex Nut 18 UNC Grade 5 * *
71 SZ8401809 Access Plug 1 1
73 SZ2010043 1-1/4" Steel Bearing w/Set Screw 12 14
SZ65062MSCI000 Flange Housing for Steel Bearing 24 28
SZ650PSB206228 Replacement 1-1/4" Wood Bearing (2 Pieces) * *
SZ992018881001 Replacement Flange Housing (Slotted for in place
install)
* *
75 SZ126063 BLT HHCS 3/8-16UNC 3/4 24 28
SZ127009 WSHR LCK 3/8 24 28
SZ125007 Nut Hex 3/8-16UNC 24 28
76 SZ0168131 Gear Box (7/16" Cross Hole) 1 1
77 SZ126088 BLT HHCS 1/2-13UNC 3/4 8 8
SZ127012 WSHR LCK 1/2 8 8
78 SZ1629350 Gear Box Shield (PTO) 1 1
81 SZ0161348B Non-Separable Shielded IID w/ Shear Clutch 1 1
SZ126067 BLT HHCS 3/8-16UNC 1-1/2 1 1
SZ125030 Nut LCK 3/8-16UNC Nylock 1 1
82 SZ6007025 7/16" x 2-1/2" Spiral Expand Pin 1 1
83 SZ4193011 Drop Spout w/ Relief Door 1 1
84 SZ2031162 10" 1 Bolt Half Clamp 1 1
SZ126067 BLT HHCS 3/8-16UNC 1-1/4 2 2
SZ127009 WSHR LCK 3/8 2 2
SZ125007 Nut Hex 3/8-16UNC 2 2
85 SZ1628815 Implement Input Driveline Hanger 1 1
86 SZ1630334 Lower Driveline Shield, 334" 1
SZ1630366 Lower Driveline Shield, 366" 1
87 SZ125032 Nut LCK 1/2-13UNC Nylock 1 1
SZ103417 BLT HHCS 1/2-13UNC 8 G5 1 1
88 SZ4127086 Driveline Sleeve Coupler (7/16" Cross Holes) 3 3
89 SZ6007017 7/16" x 1-3/4" Spiral Expand Pin 6
90 SZ0931045 Auger Intake Cage 1 1
93 SZ127009 WSHR LCK 3/8 6 6
SZ126067 BLT HHCS 3/8-16UNC 1-1/4 6 6
SZ125007 Nut Hex 3/8-16UNC 6 6
118 SZ103417 Track Car Stop Pin 1 1
119 SZ6003615 3/16" x 1-1/2" Cotter Key 1 1
120 SZ2029604 Stop Flag Sign 2 2

20
Parts - 1066 & 1076 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
76
121 SZ2029605 Stop Lift Flag Arm Assembly 2 2
122 SZ6003531 5/32" x 1-1/4" Cotter Pin 2 2
123 SZ102436 Nut LCK #10-24UNC Nylock 4 4
SZ126026 BLT HHCS #10-24UNC 3/4 4 4
127 SZ126047 BLT HHCS 5/16-18UNC 1 G5 2 2
SZ125034 Nut LCK 5/16-18UNC Squeeze 2 2
128 SZ0219860 Spring, Stop Lift Sign 2 2
130 SZ0114110 4 Bolt Hub w/ Bearing Cups 2
SZ0116021 6 Bolt Hub w/ Bearing Cups 2
131 SZ100126 Inner Bearing Cup 2
SZ100152 Inner Bearing Cup 2
132 SZSE-1100 Grease Seal 2
SZ0203549 Grease Seal 2
133 SZ100125 Inner Bearing Cone 2
SZ100151 Inner Bearing Cone 2
134 SZWB10000 1/2" x 1-1/4" Wheel Bolt 8 12
135 SZDC-1200 Dust Cap 8
SZDC13 Dust Cap 2
136 SZLM11949 Outer Bearing Cone 2
SZ100125 Outer Bearing Cone 2
137 SZLM11910 Outer Bearing Cup 2
SZ100126 Outer Bearing Cup 2
138 SZ601.5X03/4WA 1-1/2" O.D. x 3/4" ID x 10 ga Spindle Washer 2
SZ600X15016WA 2" OD x 15/16" ID Spindle Washer 2
139 SZP251703 Slotted Spindle Nut 2
600NUT0SLOT0 Slotted Spindle Nut 2
140 SZ66C5/32X13/4 5/32" x 1-3/4 Cotter Pin 2
SZ66C5/32X21/4 5/32" x 2-1/4" Cotter Pin 2
141 SZ29700 Owner's Manual Container Tube 1 1
142 SZ126029 BLT HHCS 1/4-20UNC 3/4 2 2
SZ127008 WSHR LCK 1/4 2 2
SZ125005 Nut Hex 1/4-20UNC G5 2 2
150 SZ126065 BLT HHCS 3/8-16UNC 1 G5 3 3
SZ127009 WSHR LCK 3/8 3 3
SZ127002 WSHR FLT 3/8 3 3
SZ125007 Nut Hex 3/8-16UNC 3 3
157 SZ126069 BLT HHCS 3/8-16UNC 1-3/4 4 4
SZ125007 BUT HEX 3/8-16UNC 4 4
SZ127009 WSHR LCK 3/8 4 4