Fast & Fluid Management SK550 1.1 User manual

V. 2.0
Fast & Fluid Management B. V.
PO Box 220
2170 AE Sassenheim
The Netherlands
www.fast-fluid.com
Manual SK550 1.1

2
© Fast & Fluid Management B.V.
This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, photocopying, recording, nor otherwise, without the prior written permission of Fast & Fluid
Management B.V.
This manual could contain technical inaccuracies or typographical errors.
Fast & Fluid Management B.V. reserves the right to revise this manual from time to time in the contents thereof without the
obligation of Fast & Fluid Management B.V. to notify any person of such revision or change.
Details and values given in this manual are average values and have been compiled with care. They are not binding, however,
and Fast & Fluid Management B.V. disclaims any liability for damage or detriments suffered as a result of reliance on the
information given herein or the use of products, processes or equipment to which this manual refers. No warranty is made that
the use of the information or of the products, processes or equipment to which this manual refers will not infringe any third
party’s patents or rights. The information given does not release the user from making their own experiments and tests.

3
Table of Contents SK550 1.1 V 2.0
Table of Contents
1 About this manual......................................................................................................... 5
1.1 How to work with the manual............................................................................................ 5
1.2 Record of changes ...........................................................................................................5
2 Safety ............................................................................................................................. 6
2.1 Intended use..................................................................................................................... 6
2.2 Liability.............................................................................................................................. 6
2.2.1 General liability..................................................................................................... 6
2.2.2 Machine-specific liability....................................................................................... 6
2.3 User qualification for installation....................................................................................... 7
2.4 CE certification ................................................................................................................. 7
2.5 Safety symbols on the machine........................................................................................ 7
2.6 Safety symbols in the manual........................................................................................... 7
2.7 Disposal of the machine ................................................................................................... 8
3 Operator manual ........................................................................................................... 9
3.1 Description........................................................................................................................ 9
3.1.1 Overview of the machine...................................................................................... 9
3.1.2 Overview of the control panel............................................................................. 10
3.1.3 Type plate: serial number................................................................................... 10
3.1.4 Type plate: details .............................................................................................. 11
3.2 Operation........................................................................................................................ 11
3.2.1 Turning on the machine...................................................................................... 11
3.2.2 Turning on the machine when the machine is in hibernation ............................. 11
3.2.3 General shaking procedure ................................................................................ 12
3.2.4 Placing the can................................................................................................... 12
3.2.5 Start the machine ............................................................................................... 13
3.2.6 Adjust the shake time during operation (optional) .............................................. 14
3.2.7 Remove the can ................................................................................................. 14
3.2.8 Stop the operation manually............................................................................... 14
3.2.9 Using the emergency stop switch....................................................................... 14
3.2.10 Restart the machine ........................................................................................... 15
3.3 Maintenance................................................................................................................... 15
3.3.1 General safety instructions for maintenance ...................................................... 15
3.3.2 General cleaning: after every operation ............................................................. 15
3.3.3 Periodic maintenance: weekly............................................................................ 15
3.3.4 Periodic maintenance: monthly .......................................................................... 15
4 Installation ................................................................................................................... 16
4.1 Unpack the machine....................................................................................................... 16
4.1.1 Remove the cardboard....................................................................................... 16

4
Table of Contents SK550 1.1 V 2.0
4.1.2 Remove the plastic foil ....................................................................................... 16
4.1.3 Unlock the machine............................................................................................ 17
4.1.4 Remove the wooden blocks ............................................................................... 17
4.1.5 Remove the transport brackets .......................................................................... 18
4.1.6 Dispose of the packaging material ..................................................................... 18
4.2 Put the machine in position ............................................................................................ 18
4.2.1 Move the machine from the pallet ...................................................................... 18
4.2.2 Move the machine to the final location ............................................................... 18
4.2.3 Level the machine .............................................................................................. 19
4.3 Finish the installation...................................................................................................... 19
4.4 Select the user ID code .................................................................................................. 19
5 Troubleshooting.......................................................................................................... 21
5.1 General troubleshooting procedure................................................................................ 21
5.2 Contact service............................................................................................................... 21
5.3 Error messages and other faults .................................................................................... 21
6 Technical data ............................................................................................................. 22
6.1 General specifications .................................................................................................... 22
6.2 Dimensions and mass .................................................................................................... 22
6.3 Ambient conditions ......................................................................................................... 22
6.4 Noise level...................................................................................................................... 23
6.5 Safety classifications ......................................................................................................23
6.6 Electrical specifications .................................................................................................. 23
6.7 Electrical diagram ........................................................................................................... 24

5
About this manual SK550 1.1 V. 2.0
1 About this manual
The manual shows the information necessary to:
-install
- operate
- perform basic maintenance
- correct small problems.
The SK550 1.1 and all its versions are referred to in the manual as the ’machine’.
This manual contains the original instructions. The original language of the manual is English. All other language
versions are translations of the original instructions.
1.1 How to work with the manual
For the safe use of the machine, it is important:
1 To familiarize yourself with the structure and content.
2 To read the safety chapter in detail and make sure you understand all the instructions. See chapter 2.
3 To carry out the actions completely and in the given sequence.
1.2 Record of changes
/i
Edition Editor Check Date Description
1.0 ET TB 03/2015 First edition
2.0 ET TB 09/2018 Updates due to change of control panel and general updates

6
Safety SK550 1.1 V. 2.0
2 Safety
2.1 Intended use
The machine is designed to shake colorants in a can. Any other use of the machine is strictly forbidden.
2.2 Liability
2.2.1 General liability
Our machines and accessories are fully compliant with the CE regulations. Any modification can result in not
fulfilling the CE safety requirements and is therefore not allowed. Fast & Fluid Management B.V. will not accept
any responsibility in case of modifications to machines and/or accessories.
Fast & Fluid Management B.V. is not liable if you do not follow the rules below:
- The machine is for indoors use only.
- This machine may only be used for commercial settings. The machine is not a household appliance.
- Observe all local safety regulations.
- Strictly obey the safety instructions in this manual.
- Mind the minimal requirement of the building structure of the load capacity of the floor.
- Place machine in a well-lit and well-ventilated room.
- Install and connect the machine according to the instructions in this manual.
- Connect the machine to a grounded wall socket.
- Do not use extension cords or inadequately rated power cables.
- Make sure that the power cable is freely accessible.
- Do not place objects on top of the machine.
- Keep lids, panels, and covers closed and in place whenever possible.
- Do not use a damaged machine. When you have doubts, contact your supplier. See §5.2.
- Keep the machine in good condition.
- Clean the machine at the intervals and when dirty.
- Make sure that defective parts are immediately replaced.
- Remove spilled liquids immediately, and unplug the machine in case of large spillages (> 500mL).
- Replace parts only with original Fast & Fluid Management B.V. spare parts.
All maintenance beyond the scope of this manual must be carried out by a qualified service technician that Fast
& Fluid Management B.V. has trained and certified.
2.2.2 Machine-specific liability
The machine cannot be used in an environment where explosive vapours may occur (ATEX zone). Colorants
that contain flammable solvents can be mixed, as long as they are packed in a suitable UN approved container.
Please consult the health & safety officer of your paint supplier and/or colorant supplier on how to avoid the
emergence of hazardous situations like personal harm or the risk for fire and explosion.
WARNING
Read the manual before you install or use the machine. Failure to do so can result in personal
injury, death or property damage.

7
Safety SK550 1.1 V. 2.0
- Personal harm should be avoided by strictly following the materials safety data sheets (MSDS) for colorants
and (base) paint.
- The use of flammable colorants or colorants that diffuse potential explosive vapors may present fire and
explosion risks.
2.3 User qualification for installation
Only install the machine if you have written permission from the supplier of the machine.
2.4 CE certification
The machine is CE certified. This means that the machine complies with the essential requirements concerning
safety. The directives that have been taken into consideration in the design are available on www.fast-fluid.com.
2.5 Safety symbols on the machine
/i
2.6 Safety symbols in the manual
/i
CAUTION
Disconnect power supply
before servicing
Read the manual
Maximum load weight.
See §6.1 Central earthing point
WARNING
Can cause personal injury.
Note
Shows further information.
CAUTION
Can cause damage to the machine.

8
Safety SK550 1.1 V. 2.0
2.7 Disposal of the machine
1. Sort the machine, the accessories and the packaging for
environmentally friendly recycling.
2. Do not dispose of the machine into domestic waste. Dispose
of the machine according to local regulations.

9
Operator manual SK550 1.1 V. 2.0
3 Operator manual
3.1 Description
3.1.1 Overview of the machine
A: Net entry
B: Type plate. See also § 3.1.4.
C: Spindle
D: Door
E: Lid padding
F: Can handle retainer
G: Wheels
H: Adjustable feet
I: Can table
J: Can plate
K: Control panel. See also § 3.1.2.

10
Operator manual SK550 1.1 V. 2.0
3.1.2 Overview of the control panel
A: Main switch
B: Emergency stop switch
C: Program keys
D: Stop/Up key
E: Display
3.1.3 Type plate: serial number
Note
The display shows the program menu.
Model
Brand
XXXXX-XX Xxxxxxxx Xxxxx
Xxxxxxxx
Serial Number
Production week
XXXXXXXXX-XXXXXX
XX-XXXX
THE TINTING COMPANY
www.fast-fluid.com
Fast & Fluid Management B.V.
IDEX Dispensing
P.O. Box 220
2170 AE Sassenheim
The Netherlands

Operator manual SK550 1.1 V. 2.0
11
3.1.4 Type plate: details
3.2 Operation
3.2.1 Turning on the machine
1. Connect the power cable to the grouned wall socket.
2. Make sure that the emergency stop switch is released.
3. Set the main switch to ‘ON’. When the machine is on, the
display shows the default shake times.
3.2.2 Turning on the machine when the machine is in hibernation
When the machine is in hibernation, the illumination of the display
is off and the display shows the Fast & Fluid logo.
1. Push any key. When the machine is on, the display shows the
default shake times.
3.2.3 General shaking procedure
1. Place the can. See § 3.2.4.
2. Start the machine, See § 3.2.5.
THE TINTING COMPANY
www.fast-fluid.com
XXX V ~ XX/XX H z XXX W
Model XXX XX-XXX
Brand Xxxxxxxxxxx
Serial no. XXXXXXXXX-XXXXXX
Prod.week XX-XXXX
Mass XXXkg
Fuse X AT
Patented families
XXxxxxxxx
XXxxxxxxx
XXxxxxxxx
Design
Fast & Fluid Management B.V.
IDEX Dispensing
P.O. Box 220
2170 AE Sassenheim
The Netherlands
Made in Xxxxxx
WARNING
Only push the emergency stop switch in the case of
a safety emergency.
Make sure that the problem is solved before you
reset the emergency stop switch.
When you reset the emergency stop switch after an
emergency stop, command 'press any key' will
appear.
Note
For first time use, select the user ID code.
See §4.4.

Operator manual SK550 1.1 V. 2.0
12
1. Push any key. When the machine is on, the display shows the
default shake times.
3.2.3 General shaking procedure
1. Place the can. See § 3.2.4.
2. Start the machine, See § 3.2.5.
3. Remove the can. See § 3.2.7.
3.2.4 Placing the can
Open the doors
1. Open the doors (A). Use the handle (B).
Place the can
1. Put one or more cans (A) in the centre of the can table, or in
a pattern that has its gravitational centre in the middle of the
can table.
Note
The door is unlocked when the display shows
‘READY!’.
A
B
A
A A
A A
A
A
12
34
WARNING
It is possible that the can is heavy. Use the
correct lifting tool when appropriate. Obey the
local regulations.
CAUTION
Make sure that all cans have the same height.
Do not stack cans upon each other.
Note
If the can plate and the can table are too close
to each other, use the Stop/Up key to move the
can plate upwards, see § 3.1.2.

Operator manual SK550 1.1 V. 2.0
13
Retain the can handle
1. If you place one can, make sure that the can handle (A)
cannot move. Use the can handle retainer (B).
2. If you place more than one can at the same time, make sure
that the can handles cannot move. Use a can handle retainer,
for example self-adhesive tape.
Retain the can (optional)
1. Put the lid padding on the can.
Close the doors
1. Close the doors (A). Use the handle (B).
3.2.5 Start the machine
1. Select the shake time by pushing one of the program keys.
The doors are locked and the machine starts.
B
A
Note
Sometimes the space between the lid of the can
and the can plate causes the can to move during
operation. Use the lid padding to prevent the
displacement of the can.
A
B
A
Note
The default shake times are 30 seconds, 1, 2,
and 3 minutes.

Operator manual SK550 1.1 V. 2.0
14
3.2.6 Adjust the shake time during operation (optional)
1. Use the program keys to increase (+) or decrease (-) the
shake time.
3.2.7 Remove the can
1. Open the doors (A). Use the handle (B).
2. Remove the can handle retainer from the can handle.
3. Remove the can.
3.2.8 Stop the operation manually
1. Push the Stop/Up key.
2. Wait until the display shows “READY!”. The doors are
unlocked.
3. If necessary, remove the can. See § 3.2.7.
3.2.9 Using the emergency stop switch
1. Push the emergency stop switch (A). The machine stops
immediately.
2. Solve the problem as quickly as possible.
3. Reset the emergency stop switch by turning the emergency
stop switch.
4. Press one of the keys to start the machine.
Note
During operation:
- The display shows the remaining shake time.
- You can adjust the shake time.
A
B
A
Note
If the can plate and the can table are too close
to each other, use the Stop/Up key to move up
the can plate, see § 3.1.2.
A
CAUTION
Only push the emergency stop switch in case
of a safety emergency. Do not use the
emergency stop switch as an on/off function!

Operator manual SK550 1.1 V. 2.0
15
3.2.10 Restart the machine
1. Set the main switch to the off position.
2. Wait 30 seconds.
3. Turn on the machine. See § 3.2.1.
3.3 Maintenance
3.3.1 General safety instructions for maintenance
3.3.2 General cleaning: after every operation
1. Clean the machine with a cloth and remove all spilled paint or
other liquid.
3.3.3 Periodic maintenance: weekly
1. Remove all spilled paint from the machine.
2. Grease the spindles.
3.3.4 Periodic maintenance: monthly
1. Remove all spilled paint and dirty grease from the machine.
2. Add new grease.
3. Grease the sliding parts.
Note
After the reset, the machine is on and initiated
when the display shows the shake times.
WARNING
Check the MSDS of the colorants about
personal protection measures required for
handling the colorant.
CAUTION
Do not use cleaning agents based on organic
solvents to clean the machine.

Installation SK550 1.1 V. 2.0
16
4 Installation
4.1 Unpack the machine
4.1.1 Remove the cardboard
1. Remove the cardboard (A).
4.1.2 Remove the plastic foil
1. Remove the plastic foil (A).
A
A

Installation SK550 1.1 V. 2.0
17
4.1.3 Unlock the machine
1. Remove the bolts (A) at both sides of the machine. The
wooden blocks (B) are now free to move.
4.1.4 Remove the wooden blocks
1. Remove the wooden blocks from the machine. Use the cord
(A).
2. Make sure that all loose parts are removed from the machine:
B
A
CAUTION
If you do not remove all loose parts, this can
cause severe damage to the machine when it is
in operation.
A
Note
Store the removed parts for later use. They are
needed for future transportation.

Installation SK550 1.1 V. 2.0
18
4.1.5 Remove the transport brackets
1. Remove the screws (A).
2. Remove the transport brackets (B).
4.1.6 Dispose of the packaging material
1. Dispose of the packaging material in an environmentally
friendly way, according to local regulations, see §2.7.
4.2 Put the machine in position
4.2.1 Move the machine from the pallet
1. Optionally, place a ramp (A).
2. Push the machine from the pallet on to the ground.
4.2.2 Move the machine to the final location
17mm
4x
A
B
A
WARNING
Do not use a forklift.

Installation SK550 1.1 V. 2.0
19
1. Push the machine to the final location.
2. Connect the power cable to the net entry.
3. Connect the power cable to the wall socket.
4.2.3 Level the machine
1. Move down the adjustable feet (A) until the wheels (B) are off
the ground.
2. Adjust the height of the feet and make sure that the machine
is leveled.
3. Tighten the nuts (C) to lock the feet.
4.3 Finish the installation
1. Turn on the machine. See § 3.2.1.
2. For first time use, select the user ID code. See §4.4.
4.4 Select the user ID code
WARNING
Mind the minimum requirement of the load
capacity of the floor. See §6.2.
Note
Make sure the final location is well-lit and well-
ventilated.
Note
The power cable is also used as a device to
disconnect the power. Make sure that the power
cable is freely accessible.
A
B
C
17mm
Note
The default user ID code is “0000”.
Note
You can choose a user ID code only one time. If
you have chosen the wrong user ID code, the
machine uses the default user ID code. See §5.3.

Installation SK550 1.1 V. 2.0
20
1. Select the user ID code. Use the program keys. Refer to the
table.
2. Choose the user ID code. Use the Stop/Up key (E).
/i
CA D EB
Key Function
A To go to the previous value of the digit
B To go to the next value of the digit
C To increase the value of the digit
D To decrease the value of the digit