feather&black Ercol pimlico 2 door wardrobe 10PIM 2000 User manual

ercol
Thank you for purchasing this pimlico 2 door wardrobe. Please read the instructions carefully before use to en-
sure safe and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
This item is HEAVY
Please check the pack contents before attempting to assemble this product. A full checklist of components
is given in this leaflet. If any components are missing, please contact the retailer from whom you bought
this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 20 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
pimlico 2 door wardrobe
10PIM 2000

Fittin s and parts checklist
A Drawer unit x 1 J Phillips bolt x 8
B LH side panel x 1 K 30mm screw x 16
C RH side panel x 1 L 25mm screws x 14
D Door frame x 1
M
Dowels x 10
E Top panel x 1
N
Wedge x 2
F Back panel x 1 O
brackets x 2
Strap x 1
G Hanging rail x 1 P Screws x 2
H L handle x 1 bolts x 4
I R handle x 1

Step by step assembly instructions
1. Check that all the dowels are present on the side panels B & C as shown below.
2. Push the dowels on the bottom of the side panels into the holes on the top of the drawer unit A and
secure with the 30mm screws K.

3. Attach the door frame, D onto the side panels B & C and drawer unit A using the 30mm screws K,
and the Phillips head bolts J.
4. Attach the top panel, E onto the side panels B & C
using the 30 mm screws K.
E

5. Attach the panel F to the rear of the wardrobe using the 30mm screws,L as shown.
6. Put the hanging rail, G into the hanging rail supports inside the wardrobe.
F
E

7. Fix the handles H and I onto the doors using the bolts Q.
se the screw 15mm screw, P to fix one of the brackets to the middle of the top of the wardrobe at
the back.
Wall fixin - if in doubt seek professional advice
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily pull
away from the core
structure
Brick or Masonry
se an appropriate
wall plug provided you
are sure your wall is
sound
Cavity wall
Special toggle
wall plugs are
needed. Seek
expert advice

8. Screw one of the brackets onto the top of the wardrobe in the middle along the back, see below.
Position the wardrobe against the wall where you want it to go, place the second bracket
onto the wall above the one fixed to the wardrobe and mark where the hole come on the wall. Move
the wardrobe away from the wall.
9. Attach the wall bracket using screws suitable for your type of wall, see Wall fixin s above.
10. Place the wardrobe back against the wall so the two brackets match up and tie them together with
the plastic strap provided. The plates need not match exactly, but the plastic tie must go through
each plate. Close the strap, but do not over tighten it. See diagrams below.

11. If the wardrobe is not level on your floor, use the wedges provided. Snap them off so they do not
protrude out from the wardrobes legs. You can also snap them lengthways.
12. Check that the doors are aligned correctly. If necessary adjust the door hinges as shown below

Safety Instructions
Never drag furn ture when mov ng t, always l ft t. Please take care when handl ng or mov ng the furn ture
as careless handl ng may cause damage or njury. No l ab l ty w ll be accepted for damage or njury caused
by ncorrectly nstalled furn ture.
Care and maintenance
Wood Furniture
Wood di play different grain pattern depending on which way it i cut - for example, the ‘medullary ray’
which can appear on oak furniture i a mark of good quality timber - the e are ju t characteri tic of the nat-
ural beauty of the wood. Some furniture i al o deliberately aged and ru tic.
All timber urface will change colour and mellow over time. New furniture will initially vary in hade from
item that have been previou ly purcha ed.
How to care for your wood furniture
Furniture with a hard lacquer, wax poli h or painted urface hould be du ted with a dry cloth.
When us ng the surface for serv ng food and dr nks t s best to use protect ve mats and coasters.
Sp llages should be w ped up as soon as poss ble.
Spray poli he are be t avoided a they contain ilicone which may poil the furniture’ urface by building
up over time. Use of clean ng mater als conta n ng abras ve compounds, ac d c or caust c reagents and any
bleaches conta n ng ox d s ng reagents should be avo ded as prolonged use may damage the lacquer sur-
face.
Wipe up pill immediately. If ticky mark occur on the urface they can be removed with a dilute olution
of warm oapy water. The offend ng area should be rubbed l ghtly and then completely dr ed mmed ately
afterwards, before replac ng any mats etc.
Our furniture will endure mo t temperature in the home but it i be t to avoid placing furniture next to
heat ource uch a radiator or fire . Be particularly careful with olid wood a the lack of humidity cau ed
by central heating can cau e damage uch a warping.
ercol
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Feather & Black, Terminus Road, Chichester. West Sussex. P019 8ZZ 01243 380601 www.featherandblack.com