FEB 767FR Series User manual

Series 767FR/LF767FR
Anti-Siphon Pressure Vacuum Breaker
featuring Replaceable Seats
Sizes: 1⁄2"- 2" (15-50mm)
RP/IS-F-767FR
INSTALLATION INSTRUCTIONS
767FR/LF767FR
1"-2"
(25-50mm)
767FR/LF767FR
1/2", 3/4"
(15, 20mm)
Function: To protect the potable water supply from backflow from a non-
potable source due to a drop in supply.
Protection: Pressure i.e. backsiphonage
Installation Instructions
Requirements:
1. Install 12" (300mm) above highest point of downstream piping.
2. Install bonnet side up and allow for accessibility for testing/service.
3. Install where discharge or spillage is not objectionable.
4. Do not undersize supply or oversize the valve in relation to demand.
5. Do not install where backpressure can occur.
6. Protect from extended freezing.
7. ASSE Standard 1020 requires that the atmospheric vent valve remains
open until the valve bodypressure exceeds 1 lb. Until this pressure is
reached, some amount of spillage will occur at the atmospheric vent. In
order to minimize this leakage on start-up, close the downstream shut-
off valve and open inlet shutoff valve quickly
Recommended Service:
1. Test periodically as required by local jurisdictional authorities.
2. Open test cocks to drain in cold climates if only operated seasonally.
3. Replace rubber goods every 5 years.
Pressure-Temperature:
Working Temp: 33°F -140°F (0.5°C-60°C)
Max. Pressure 150psi (10.3 bar)
Min. Pressure 15psi (103kPa)
IMPORTANT: INQUIRE WITH GOVERNING AUTHORITIES
FOR LOCAL INSTALLATION REQUIREMENTS
Limited Warranty: FEBCO warrants each product to be free from defects in material and
workmanship under normal usage for a period of one year from the date of original ship-
ment. In the event of such defects within the warranty period, the Company will, at its
option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY
WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE
COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY
HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and
exclusive remedy for breach of warranty, and the Company shall not be responsible for any
incidental, special or consequential damages, including without limitation, lost profits or the
cost of repairing or replacing other property which is damaged if this product does not work
properly, other costs resulting from labor charges, delays, vandalism, negligence, fouling
caused by foreign material, damage from adverse water conditions, chemical, or any other
circumstances over which the Company has no control. This warranty shall be invalidated
by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some
States do not allow the exclusion or limitation of incidental or consequential damages.
Therefore the above limitations may not apply to you. This Limited Warranty gives
you specific legal rights, and you may have other rights that vary from State to State.
You should consult applicable state laws to determine your rights. SO FAR AS IS
CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY
NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE
YEAR FROM THE DATE OF ORIGINAL SHIPMENT.

Repair Kits 1⁄2"- 2" (15-50mm)
ORDERING CODE MODEL SIZE
in mm
Check Kits
0710590 RK 767FR CK 1⁄2, 3⁄415, 20
0710591 RK 767FR CK 1 25
0710592 RK 767FR CK 11⁄4- 2 32 - 50
Kits consist of: Check disc assembly (disc & disc holder). Bonnet 0-ring and Check Spring.
Vent Float Kits
0710593 RK 767FR V 1⁄2, 3⁄415, 20
0710594 RK 767FR V 1 25
0710595 RK 767FR V 11⁄4- 2 32 - 50
Kits consist of: Float vent disc assembly (vent float, seal & spring) and Bonnet 0-ring.
Bonnet Assembly Kits
0710596 RK 767FR B 1⁄2, 3⁄415, 20
0710597 RK 767FR B 1 25
0710598 RK 767FR B 11⁄4- 2 32 - 50
Kits consist of: Bonnet, Bonnet O-ring, Vent spring, hood & hood screws.
Rubber Parts Kits
0710599 RK 767FR RT 1⁄2, 3⁄415, 20
0710600 RK 767FR RT 1 25
0710601 RK 767FR RT 11⁄4- 2 32 -50
Kits consist of: Vent disc, Check disc and Bonnet O-ring.
Seat Kits
0710602 RK 767FR S 1⁄2, 3⁄415, 20
0710603 RK 767FR S 1 25
0710604 RK 767FR S 11⁄4- 2 32 - 50
Kits consists of: Seat, Seat O-ring and Bonnet O-ring.
FEBCO reserves the right to change or modify product design, construc-
tion, specifications, or materials without prior notice and without incurring
any obligation to make such changes and modifications on FEBCO prod-
ucts previously or subsequently sold.
Freeze Protection Guidelines
Purging of a PVB Assembly with Pressurized Air
1. Close main shutoff valve.
2.
Open upstream drain, test cocks and isolation ball valves
to depressurize line.
3. Purge with pressurized line.
4. Leave test cocks and isolation ball valve handles in 45°
angle to drain ball valves and prevent casting damage.
Outlet Drain
Valve
Main Shutoff Valve
Upstream (Inlet) Drain
Flow
Valve Pit
12" Minimum Clearance
Above the Highlest Point of
Downstream Piping
Sprinkler System
Piping
Zone Control
Servicing the Vacuum Breakers
Internal parts can be removed, repaired or inspected without removing the
valve from the piping.
Disassembly
1. Shut off the supply pressure and drain the valve.
2. Remove the two hood screws and the hood.
3. Place a wrench on the parallel flats of bonnet and stem assembly.
Turn counter clockwise and remove.
4. Remove the vent assembly.
5. Press down on the spring retainer and disengage it from the
retaining lugs. Then turn 90° and remove.
6. Remove the spring retainer and spring. Note that the large
diameter of the spring is down on the guide assembly.
7. Remove the check disc holder and guide assembly.
8. Disassemble the check disc holder assembly.
Reassembly
Reassemble in the reverse order utilizing the new parts from the repair kit.
Installation Instructions
Using FPHB-1 Hydrant
Note: PVB's must be installed a minimum of 12" (300mm) above
the highest point of water in the sprinkler system.
Water Supply
FPHB-1 with FEBCO
767FR Series
To Sprinklers
Drain Port or Blow Down
767FR/LF767FR
1"-2"
(25-50mm)
767FR/LF767FR
1/2", 3/4"
(15, 20mm)
USA: 4381 N. Brawley • Ste. 102 • Fresno, CA • 93722 • Tel. [phone] • Fax: [phone] • www.FEBCOonline.com
Canada: 5435 North Service Rd. • Burlington, ONT. • L7L 5H7 • Tel. [phone] • Fax: [phone] • www.FEBCOonline.ca
RP/IS-F-767FR 1006 EDP# 1915947 © 2010 FEBCO
A Watts Water Technologies Company