Feelsafe OMNI 3000 User manual

Ho&-up. & InstaIIation
.
.JuLY 86'
FeelWe, Inc., 50 En@eers Rood. Houpwuge. New York’1 1788
(516) 5824161 [phone] :. .-
TM
Copyrjgtlt @ L98b FeelSafe, Inc. , . Printed in U.S.A.

N .

‘n fmctbs
l ----
The’BMNI 3000 is a multizone Control Panei and Digital Communicaror. There !
is one (1) E.O.L. Supervised Fire Zone; one (1) Common Trouble Zone, and I.- - - --
Twelve (12) E-0-i. Supervised Programmable zones. The OMNI 3000 Sysrem is. i
controlled by the OMNI 3OOOR four (4) wire keypad.
may ibe. used in conjunction’.with this system. A maximum of four keypads I
i
Each keypad has one (1) armed Led, I _
three (3) yellow leds (AC, Fire Trouble and low Batrery) and Twelve (12) green ,
;..--
Leds which display loop sTaTus, bypass sTatus, and alarm memory of zones one (1)
through nvelve (12). \ __ _
.The OMNI 3000 System will store as many as eight (8) user I
arm/disarm codes, all of which can reporr separate opening and closing codes if \
.. necessary. Furthermote, these codes can be prqgrammed to permit three (3) digit i ___
arming, but. szill maintain full code disarming. User code five (5) is programmable I ’
as a temporary arm/disarm code if desired. Lastly, all user codes will be srored I
- --.. - .- -- _---. --- -
in EEPROM fo PREVENT loss :if rhere is p roral sysrem powerdown. : I --
- 1
There are actually four (4) separare manuals which pertain to this synem. OMNI 3000: .
Hookup and lnstallarion Manual, I-2258 which will explain all.fieid wiring (keypad,
loops, bells, phone lines, etc.) and Keypad Programming. OMNI 3000 Programming I
lnsrrution I-2261 which exptins all prom programming. OMNI 3000 Advanced ! .- _
Communication Manual, I-2259 explains prom programming with reference to ad- I
vanced dialer communications. The fourth ‘and final manual I-2262 is an End User , ’
Guide designed to he!p the cusomer become famiiiar with his system. i
. ------... ,. _..__
.
-. I
0 .
..- _.
.. .
Terminals 6: Descriorions . --- .-.
--- __ -
I ‘Terminal 1Descriouon
1 /RED - ._
2 1 BLACK Wires from OMNI 3000R.keypad 1
-.-
I 3 I
GREEN
t I
4 t-y=ll~ow “. .
5&6 1E-O-!- Suoervlsed Zone I: Wire nor&lv uosed devices !n sencs, a.nd;or normal.& .*
L0.L” 1ooclzL open aev&s in parallel with the lOOOr,~O~. resissor- Maximum loop resisrance . ,I
is.1250+ WITH rhe 50-L. resixor.
-- ione- 1 can be programmed on me prom as a’ __
DELAY, INSTANT, Oc-AN INT-ERI.OR ZO-NE..
-- _ ___ _ .
I I -. _ -_--. ... w-P____ _ -._- _____-..- - -. I
Zone operation is as follows::
system is armed, if EXIT DOE.5 NOT take place during 5i-r Time\
of the zonczs whicn has been sdec~ec! as t DELAY fONE.(exampier say!
rhe INTERIOR ZONE will be AUTOMATICALLY bypassed.
is md and -5iZ DOES raker pkce mrough a dday zone:
RlOR zone will have “Jlrrance a+ay: if Re-entry is througir.
Delay zoneL .Jf Rt-cozy is ~hrougn any, circuit omtr man a’,
will ‘be. irzsrarz- : ._
.
-.- .-. .. - _’
4
I. . .
-.

1-14& 15
:50-L. 1DDk
.I----
‘l5.&J6
LO1 lOOI+--’
50-L k~~~~eed ione 2: Wire norm&y c.ioxd mviccs in merits and/or normally
LO-L. 5uDetvistd Zone 3: same wiring-and options as zone 2
LOLL. ‘Suxt-vised Zone L: same wiring and oFtions as zone 2 .-.
,’
E-Del- Suocrvistd Zune 5: same’ wiring and .options as zone 1. This zone is
prom programmable .as a Delay, lnstarq or Interior zone only.
EC-L.‘Suoervised Zone 6:
This zone IS prom programmable as an INSTANT ZOhF ONLY. Wire normally
tioscd &evices in series and normally open devices in pardJeJ wjth The 1DDm
Z.0.L 5uoervised Zone 7: Same.wiring and operar1on.u zone 6. This
zone is prom -programmabJe as an Insran; zone ONLY.
E.0.L. ~5mecvise6 ione 8: Same wiring and operation as zone 6. ‘This
zone 15 prom programmable 25 an Inszani zone ONLY.
LO&. Suxrvised Zone 4: Lame wiring and operation as zone 6. This
zone 15 prom programmable as’an .hSiani zone ONi?‘-
5C-L. Suoervbed Zone 1D: Same wiring and Doeration a~, zone 6. This
zone .ls prom programmable 2s an instan; zone .ONLY.
SOJ- Suocrvised ione .JJ: :Same wiring and DoeraTion as
Zofte 6. This ,.::.:’
zone is ?rom programmable as an Inszani zone ONLY.
3O.L SuDervked Lone J.2: ‘Same
Wiring and DperaijDn 2~ ZDne 6. .?hiS
zone 1s prom programmabie as an instant zone ONLY-
Smoke Detector Power Termiti Reset by momeniary .act.ivatim of IOMNI 3DDDR
keypad 141 burron
3
,501. Supervised Fire Lone. Wire. normally open smoke de-rectors .in parallel witn
these rerminals. .When tie fire zone. is violared it will xrip the digital ciialer and
ring lhe burgla-y ‘bell, OR zhe fire beU depending on how %-c prom Is propammed
U this sn-~ok~ derecror ioo? .js ‘0 PEN: a COMMON TROUB” ,E ZONE nansmissionwil
occur :and tie FIRE TROUXE ZED on tie;QMNI .3OUDR&eypad wilJ‘&n ‘OFF. The
~S-2K-EOL resxxor -.-. .,- .-. MUST be cDnn&&d ID these ?&xiina.ls whetfier me tie zone
._
iis. used orno-,
__-
..- -; _ -’ --
. 23(i) ik -26(-J
Remore ARM STATUS 1-9 rerminti. Conneci.mode! 521M
TD tie3e term-mats,
for Remote ARM .STATUS .Annunciarion.
.
_.
&m . Remote An-ning.i em&&. Wire
~normaLly -open. MCMEhTTARY devices model 52lM
l
i-tizre70 arm/ci.isarmxhis system i: desired. . . -
- ._-. _. . .-
_‘I- . i.-:= -=-.2 -- .. - -
. .- _._ -- -.
4 --
.
.-\ 3(4 & ‘&(-), 12VDC. UnrepulaTed OUTPLJL All devices which
can be powered by unregulated DC
.
: voltage ma): lx connccre,d here.
. ... -_ : ‘_
1 2

\
. s 8
30. & 311
- Q-Y.
34,35 I *
36,37 ’
i!
,
jY(->
CL’38(-j
_-
__. ” . . - - _. -_- -- - ---.. -- -.-_ .___ ---
These’ terminals are%- se; of no&ally open dry contacts which dose: -.-. ..-.
whenever the fire zone is violated. They can, be returned to their normal:
condition wnen the fire zone is reset-by depressing the kFpad (#I burton. i--s
-.
These terminals are a set of norrnaliyopen ary contacts wnicn
close on burglary alarm, bell test or audible pa&c-‘&rm. They ‘will be’ .-‘.
returned to their normal. condition on bell cutoff or system disarm. !
- .- . -._ _.- ----
These terminals can be returned to’normal, after an audible-panic, by depressing:
the keypad m button. - -., - .1_.__ ..-_,L. _.- .._. _ _. __ _ __ ---. . _.
Telephone line connections ior the OMNl, 3000;on-board--digital dialer- Connecs: 1
the Model 11368cord as follows:
- --.
rd-35, green-34 t grey-37;-bpo&-t-3& and. plug I
the. male connector into a RJ3lX jack-The OMNI 300,Ohas double pole fine.;ehr&j
Beiore using tne digital dialer, the telephone company shall be requested to, .-
insrall a USOCRJ31X jack on the telephone line- Give the relephone company tie
FCC registration (AE39SEi69554AL-E) 0: the ringer eauivalence (O-08) numbers for
_--
the OMNI 3000. Connect the OMNI 3000 witi an approved modular plug (#368)/
mate with the RJ3IX as shown on the following page- -- . - . - -. .
--.
Should the OMNI 3000 cause harm to the telepnone network,the-telephone company
may temporarily discontinue servic e until rhe problem is corrrected- Notice of
such action will be given by the-telephone, company,
Should the telephone comuany make -any changes to its facility or other requiremenr
that could render the OMNI 3000 incompatible, the customer shall. be given adequate
notice by the telephone company, in writing. Upon receipt of this information
from
rhe customer, the manufacturer shall advise the customer as to what. actions mu.S
be taken to maintain uninrerrupreci service,
The Model OMNI 3000 may nor be connected to party Iines or coin lines- If trouble
is experienced, the OMNI 3000:shall be disconnected from the phone line, ‘by means
of me plug shown to aerermine if the OMNI 3OOO:is maLfuncrionmg,If me: OMNI 3OOc
is malfunctioning, do not reconnec: unrii the problem has been correcred~Th~ ’ .’
conrrol pane! should not be used in conjunction with “call waiting” phone system-
12YDC Regualred Ourput- Less than 1OOmvpp ripple. 300ma currenz caoabiliry-‘- --
These terminals can be used to power all devices such as morlon cietecrors whicit
need a consTam IZVDC regulated output. .--.
VOICE SEN DRIVER OUTPUT: 8 ohm 15 watt speakers are recommended.1
When a burglary zone, or. audible panic is tripped, the fol!owing verbal mes- .-- - ‘- .
sage will be. produced, “YOU HAVE VIOLATED A PROECTED AREA. I
THE POLICE -WERE CALLED: LEAVE IMMEDIATELY.” This message will !
be reoeared 2 times followed by 3 minutes of switch selec-able siren sound. ’
When’the fire zone is tripped, .this output will produce the following verbal .f
message, “FIRE LEAVE IM MEDIATZY.” This message will be repeated 3.
times followed by switch selectable siren sound. _.._ -. _ .
. .
..-.>:.,.
._.
7
.
. 2 > ‘.

’ \
.
‘. .
42&43 ._
,-P & BA -
r.
E&-&X
-_ .
-k? switches l-5 from the chart below for the desired siren
sounas on burglary and fire.
51
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
LEGEND
A=PULSINC BELL
kSU'EEP SIREN
C=HICH PITCH STEADY SIREN
D=F’ULSING HORN
&BELL
F=EURO?EAN SIREN
SWTCH SETTINGS
52
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
0°F
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
.ON
OFF
OFF
ON
ON
OFF
OFF
53
ON
ON
ON
ON
OFF
OIT
OFF
OFF
ON
.ON
ON
ON
OF?=
OF?=
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OF’
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OF’
OFF
ON
ON
ON.
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
.‘I i
3’PF, OF SOUND /
SS FIRE SOUNd BURG SOUND ;
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OF’
OF
OF=
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OF!=
OFF
TEST MODE ALL SOUNDS
A B
A C
A . D
A r
A i
B . A
B C
B
B
B F
C
A
C B
C D
c E
C F
D A
D B
D C
D z
D F
E A
E B
Iz
i C
.D .
rz
f F
A.
F B
F c
F D
‘F E
VOICE MESSAGE ONLY
Ui Listed .lZVA~;r’J+OVA (model 1282) transformer should be .wired to these
terminals and plugged into a 120 VACunswitched &irk. ‘.Use 16 gauge’.wire at
no ‘more tkn 15 feet- As long a AC is applied to these kminals the AC
LED will be ON- If. AC voltage is .lost on this system for ar lezs~ VQ seconds,
rhe COMMONTOUBL= - ZONE will transmit to the Cen& Office.
Normally open momentary but&s can be .wired to these terminals
which wjll riip the 24 I-IR. KEYPAD PANIC .cir.cui;. This circuit
can be programmed either audible or silent in the prom chip. .
i remote green ready led can be wired to terminals B+ (positive)
Fnd (R) (negative) which will display common loop status of all ion&s l-12
vhich are programmed as .burglary zbnes. This led will be ON when 1
ti zones are good, OFF when any one zone is violated dliring the disarmed con--
iition This .led will also remain OFF after an aiarm condition, until all k+nking
tiarm memory Jeds a’e reset., .. : .,

1r.E OMNi 300s KEYP4D
.;;;OE:
.
Tfi- .PROM CHIP-ML’S7 BE PROGRAMMED AND INSERTEE INTO THE SYZZ% PRIOR
.
a
L
j-
TO OPERATION OF..THlS KEYPAD.
The OMNI’3000R Keypad is designed to work exclusively with the OMNT 3000 Computer
Alarm System. A maximum of four (4) keypads may be used. There are 13 green, \
3 yellow, and 1 red LED displayed on the front of this device. The RED ARMED LED ; , - -. --
will be ON when the system is armed, OFF when disarmed, and BLINKING after an
aiarm hzoccurred. The yellow BAT. Lmwill be
ON when the 12VDC gel cell is good, ’ .
OFF in the event the battery voltage falls to appro=ately IOVDC. The yeUow AC ! i
LED will be ON when AC power is applied to this system, and OFF if AC power is lost. ; 1
The yellow F?-RLELED is the Fire Trouble LED.
good, and OFF ii tne Fire Loop is open. It will be E when the Fire Loop is _ 1,
-_ \ .’
_
The ?wehe green”zone LED’s correspond to zones 1-Z ‘Their operation varies
: depenciing on what TYPE each zone is programmed to
be. Operation is as follows.
NOT?? Controlled zones refers to Delay, instant, and interior zones.
ZONES STATUS LEDS OPERATION 4
Zone
Conditions~ I 24 Hr. Alarm
Zones LEDs I 2& fir, Trouble Controlled Zones iEDs, Controlled Zones
Zones LEDS
System ‘Disarmed- / LE’7s Sys. Armed
Loop Good OY I On on
b Loop Trouble 1 Off Off Of5 Fas Blink
Loop Bypassed 1 NOT Valid 1 Siow Blink I Slow Blink I Not Valid
*NOTE Controlled zone LED’s w.iU remain in the fast blinlung mode when the system is .
disarmed after an alarm until depressing m :
0
NOiE
- N67-E:'
N6TE:’
i.
._ -_ .--
Ii -_ -
9;
El
I
.
--
.
a
Zone 1 LED will also slow blink while programming the keypad, and come on steady _-.
wnen.h the INSTANT ,mode, -regardless of zone type.
_. .
The red armed led will blink every 20 seconds to indicate the
__ -. __.._ .. -.-. .L.. _
_._
;
OMNI 3000 SELF DIAGNOSTIC TEST is complete and the system
: is w_orking correctly. ___.
The green ready led will be ON s-long as all controlled zones are good- ;
and OFF if any one is violated, while the system is in the .disarmed state.
. -1 -
-2.._-- - .. : .- -,-
This Led. will also remain OFF after an alarm condition, until Reset.
KEYPAD BLJONS ,, -
-_ _.__--. -. _
_-_.
-. -. ...
This b-m is used to RfSfTr A) All smoke de-remors. ‘Bf She audible DLIrpUr
for keypad..panic, 5re zone. 21: hr alarm zones. C) All 525~ blinking alarm memory
.X35., D> JU bypassed controlled zones .zfmz~ &s&m.
her unsuccessful dialer zansmiss’ E) The slow biinking red LED
xx7 to the CO.
-2. - _ -.-- --.- .. _ . . ‘.-
- .__._
Several of the OMNI 3000:keypad numbers-serve double and ‘hiple f unctio%?The Control’ Pan
understands whichfunction ‘is de~~~~~e-sequenie’.th’~e keys .are used.“’ Keypad
Digit [?) is one of the double function keys. .
Zones 1 through ‘12 .can be .bypassed by depressing the digit (9) k&y followed by i
two. more .numbers that represent each zone respeciively. (O), (l), .for zone 1 ;
- - - _-through; _.- . 1 (I), (2) for zone 12. 6,: bypass zone 3 = depress (91,
(01, (3):) The. common trouble zone .audible output can. be byptised by :depr&r- : --
ing (VI, (O), (0). .
The same procedure should be followed for unbypassing these
zones. .
..
-. : - -. .._. _
-NOTE:. 24 HR alarm zon& cannot be bypLed. - -. - . --..-.--- - - -.
:
. -
- :
NOTE: .24 HR trouble zones, ,+$bje OF~IJT on be .bypxsed, however, eey
WILL still vnsmit to the central &ice if violated.

"+a. S'
em 1raneiusly pressing and hol&ng ~hr [lj and 133 keys for f second will T:; ‘me
d
.- ’ keypad tvEDICAL circuit This is a 21; hr. siienr. cnannel.
I .
: .-- -. - -. _ . _ __. .- - -.- -.
da’ .Simuframously pressing and holdme, Tne pound [+I] and me asrerisk [+I for f second
iwill xip The P4 hr. keypad panic circuit. U rhis circui-r is programmed as AUDIBLE
Ii; may be reset or aborretl ‘by opp,ra‘Ilon of me ill) burron. If rnis circuir 1s programmed -.-.
ias SI!.CI\‘T, the diaier mansmission CANNOT oe aborred once atrjvared.
8
The asterisk key on the OMNI 3DOOR keypad axially serves several puTposes on *is
!sysitcrn- One fun&on of rhe asterisk ‘1-1 key is fo make all programmed delay zones ,_ __ .L
IINSTANT if iI is depressed ,while -rhe OMN1’3000 is armed. The zone one Led will
Iturn ON fo indicare rhis mode fi ativared.
v-. ...
KEYPAD PROGRAMMING
Kiypad -Programming mu5; be perf armed a?‘rer the prom chip has ,been programmed and
herred jnTo TC sysrtm. BLUE DOT RIGHT-
7-w OMN] 3000 System is capable of srorq eighs tieren ; arm/disarm cooes for intiIations
which require mutriple users. This inFZ&a.Kion inxrucri0n’wil.t refer TOrhe
t2gh-i &flerenT
.cods 25 User code: C-7,
.E.ach User cooe will .aJways be five toial d@s Ion&.
The first ciiph d -each code will begm wlti m-0 respecriue User number (example: User
one= 1, User TWO = .2,
.erd. The USER ONE code is she masxer sysrem’cooe and ulill .
be rne xjnly means by whxh rhe OMNl 3000R .keypad can be programmed. The prom chip mu%
presently have a Four dig17 USER OE STARTU? CODS. This
code preceoed by keypad
dipi? .orte (1) is User one&s arm/drsarm code and Tne sysrem programmlng co& a~ The time
?ne .OMNI 3RODSysremis tis powered up (exampie: prom programmed STARTUP CODE =
3.5 rrherefortz, she User one’ code a7 powerup = 12345). I
a’ T tie time of ORIGINAL system power up: a mandatory ZIXTE number wilt be
necessary for prooer’ keypad programminE. This siti number is cabed the
. =JTzNSION DIGIT and mL?s;.be decided.27 snis Tlrne irom me ioIlowlng information
and, r&petive char,. _. . .
ioE.5.SD: TFIROUGt? T’J ELE can be inciiviciualiy bypassed a~ -rhe OMNj 3000 keypad whiie the
system is ‘m me disarmed mode. The fizz pprion which mus? be decioed is wherher %nese .
zones shouid ix AUTOMATJCAZY UNZYPP-, fED ‘uoon svnern disarm, or shouid..rtney
retin in rhe SYPjPLs condrrlon un5.t MANUALLY Uf&YPP.Z.ED.
‘NO=: iones 1 .through 5 can be programmed -ior amo unbypass .in ihe prom chip. .
The second .oprion which rnusI be determined with ihe aension DigiT .is wheihe; all
The User codes should ‘be allowed fo ARM me system witi she, iirsr TIFiREE Di@s of rheir code
.. or will i; be mandatory -ro m5lize rhe full User codes always. Whether ARM ON
THREE DIGITS is selected or NOT,
User code fo +arm ri&..spxkm. i7 will always be mandatory
TO enrer ‘rhe full
,.
The. &id and final own which ,musi be. deTermined is wherher this system should’
..-$EPOuER-UP . - .
AF!hED OR DJSARMED h?TER A TOTAL SJ’5TE.M ?OU’ER DOWN.
. - .:-‘ ..: .. - ‘;,H.. ... . ..
..
----C .-
..L.
..-. . -
T. ;::y .
..
T’L ,.i.K;‘:.;h.’
- *-.a- _.__d’ -
-2.. , - -._ .- -. . . . -. .‘- -.
.-. _-.
_.D~~RM~~~~AN-A~PRo~~~~~ ‘~~~-~~~R-~~~M TG FOLLOWING c.jiR-j- Fox’
- ?ROGXAMT~D *A-i TE OMNI 3DOOR ,EY?AD . ’
7-E EFENSION DIGIT WHICH U’JZ Zr
_- --
-. ..
.‘. ,:I NUMBER I. AUTO UNBYPFSS. ‘i ARM ON THREE
.-. DIGITS I RfPOU’ER-U? -
. II 0 I ES I YES I DISARMED
*. iI 1 I NO I YES I DLSARMSD
;I
2 I YES I NO
I DISARMED
2.. 3 ‘. I NO I. ‘NO I D!SARMED t
-
; 4 I YES I YES I ARMED
;I
5 I NO I - YfS
I ..ARMED
I, 6 I -. YES I NO- I ARMED
. #I 7 I NO I NC 1 ARMED 1
. .-.
6 2

.-
c-
.‘&
ow zhar me
Extension Digi; has been oerermined this instruc-ion manual vii!
proceed
. ! l
- ‘wr;h a srep-by-ssep procedure for system powezup and keypad programming.. - -.
l
-
:
0.
:<
The keyDad sodtr; wil] annunciare successfu.i keypress.
SE? A: All zones of the OMNI 3000 Lme-m snould be in-the UNVIOLATED nare if
possible. i --- -. .. .
_ __-.- - . --- _. - - -- -_ _.
STEP B: Apply AC firsr men DC, the System should come up in the ARMED .
CONDITION with the ZONE 1 LED ON.
SW c:
User One depress [*I, and the present User One Code (which is presenrly i
plus the prom programmed FOUR DIG7 STARTUP CODE). EXAMPLE: _.
sa~up code = 2345, -Ihertfore,
User One deprcsscs 8 , 1: 2, 3, 4, 5.
.---
STEP D: ,User One MUST depress the EXTENSION DIGIT
at this time.’ 1 -_
--
.--
\ -.
- -- - ___ _ __.__ _ .--. --
._ ._--
P__., -- -
STEP E: Select a digit from the following chart which informs this system if any of zones
. 2-4 are orom oronrammed as 24HR- ALARM ZONES or 24HR. TROUBLE ZONES.
THIS .DIGIT .. .: . MUST BE ENTERED AT THE KEYPAD AT THIS TIME.
DlCl-i- \
24tiR. ZONEi\ --
0 NONE ’
1
ZONE ?!
2
ZONE 3!
3
ZONE z&31
11 ZOK: 4.:
+ The OMNI 3000 will disarm .ar this point. 1
5 :
6
7
ZONE Z&41
ZONE 3&41
ZOhE 2,3.&b’
IT IS NOT. NE== TO DO ANY =THER PROGRAMMING .AT l%S
POINT IF THE USER ONE (1) CaDE IS THE ONiY CODE DESIRED TO
O?ERATE THIS SYSTEM AND TtiE STARTUP CODE IS ACCEPTABLE.
’ IF THE STARTUP C3DE IS NOT ACC’DTABLE, THE FOLLOWING m.
WILL EXPLAIN HOW USER ONE (1) CAN REPROGRAM HIS OWN. CDDL-
STEP F:: For purposes of understanding and simpiidry, this instruction will continue
with keypad programming assuming rhe‘numbers l&3,4,5 to be .the EXAMn’ r ‘.-
L-L-
User one code (number 1 plus s-r-r-up code of 2.3,4,5)-
- . .
While the OMNI 3000 System is disarmed User One can reprogram his present .
code as follows: Depress a ,1.2.314,5 (present USER ONE CODE), then Depress
1 again (the zone one ‘led will blink slowly). Now enter Four more keypad \ _
numbers desired EXCLUDING’NUMBER NINE (9), rexample: 4,&l&I. The
zone one.*.Led will STOD blinking.. USER-ONE’S NEW--CODE--i3 I andr!;
. __‘__.- ..-__ - ._- -
Four Digits entered .(1,4,8,7,6). - .- ---m-w, -
IT I5 NOT NECESSARY ‘TO DO ANY FURTHER PROGRAMMING AT THIS
, POINT IF THE NEW USER ONE (1’) CODE I5 THE ONLY CODE DESIRED
TO OPERA‘i-5 THIS SYSTEM. THE STARTUP CODE IS VOID AT THIS TIME
THE :FOLLOWING STEPS MAY BE FOLLOWED IF MORE KEYPAD USER
CODE PROGRAMMING IS NECESSARY.
STEP G: While the System is disarmed,. user one- can program any of ihe - -. -_-. -.__ ._._.
1. other user codes two (2) through eight (8) as foUows: Depress 3 and tne .
PRESENT USER ONE CODE (new user one code or startup code, whichever
is the present one), followed by .rhe. User number .desired to -program,
followed by Four more digits EXCLUDING NUMBER NINE (9). The follow-
_. ing example is the proper procedure if User One is going to .proFam, the
us&: .two code assuming the’present User One code is 1,4,8,7)6 and the . .
desired User two code is 2&,6,8,6.
USER ONE DEPRESS: m ‘,! ,4,x,7,6, :2, S,6,8,6

:Ssi-EP l-l: -. -
-A-.. -
The User zero (0) code and User Five (5) code borh demand 2 little more arcenrion than
?
@ mer cqdes. Botn of these codes are programmed cxacrly as me otne: user codes,
t-l vcr, both of these coots can be used for additional features in the OMNI 3000 as
follows: THE FOUR DIGIT COD E WHICH Is PROGRAMMED =THE USER ZERO
CODE CAN BE PRECEDED BY ANY USER NUMBZR,TO SEND A SILENT AMBUSH SIGNAL
TO THE CENTRAL OFfICE(.ASSUMINC THE AMBUSH FEATURE HAS BEEN PROGRAMMED
ON THE OMNl 3000 PROM CHIP.) .- .’ -.’ - . -’ - .. .
. -.- -. -e___ - -_._ .- _.-- -
The following example is the proper procedure ro.program and operate +he user zero (0)
code dor amoush. This instruction assumes the User One code fi presently 1,4,.&7,6.
EXAMPLt,: USER ONE DEPRESS: “,1,4,&7,6 -0, 3,3,3,3, *
ANY USER OF -2-l.E SYSTEM CAN NOW SEND A SILfNi AMBUSH SIGNAL BY DEPRES-
SING THEIR RESPECTIVE USER NUMBER FOLLOWED BY 3,3,3,3. EXAMPLE: 23,3,3,3
1:,3.3,3.3 6:3,3, 3.3 WILL ALL SEND AMBUSH. WHEN AMBUSH IS TRIPPED BY ANY
‘JSER THE ENTIRE SYSTEM WILL ETTHER ARM OR DISARM DEPENDING ON T.HE PANa
STATE PRIOR TO THE AMBUSH TRIP,AND THEN REPORT THE SILENT SIGNAL TO
THE CO. IF TEE AMBUSH FEATURE HAS NOT BEEN-SELECTED IN THE PROM C.HIP,
TEE USER ZERO CODE CAN,.BE PRDGRAMMED AND OPERATED THE SAM: AS THE ;
~1OTER USZR CODES.
NOTE: THE LAST FOUR DIGIT.5 O? THE AMBUSH CODE CAN NOT BE PROGRAMMED
-. _-. .~~I-?-~AME AS THE LAST. FOUR DIGITS OF ANY OF THE OJHER USER CODES.
_. .. ,.._ -- -.._. .- . ..--- -- --- -. - _-_.- _-___
Tr= USER PI\C CODE can be programmed for PERMANENT or TEMPORARY use. When
CODE is programmed, an extra digit MUST beentered that informs the
NI 3000 System how many times this code will be allowed to DISARM .
c .a digit *ram the following cnarr for the extra digi- L that must be programmed in the
Use; Five code
;:i\ij ,,..”
F-u..: I
NO+==‘. TE NUMBER Ot TIh’E.5, SELECTED FROM THE CHART IELOV’ I5 THE TOJAL
TIM3 THE ‘USSR i=JVE CODE CAN DISARM THIS SYSTEM.
.: .. j 0 ALWA\/J
. J 1
2 .2
.I 3’ 3
k a ... .... .. 4
__..
: ’ 5 5 ..‘. !
.-6 6 ’ 1 ’
‘.i 7.
.7 I
.i,
The iollotiing i&orma-rion is an e&mole of how me User
‘The: USC7 Fjve code shotild be ?rogrzmmeL
One code is zzsumed TO be i14&7,6 and me desired User Five code is 5,&7,&7
and User Five will be allowed :o disarm wifh nis code POUR (4) TIM5
fXjjM3: =.
--- USER ONE DEPRESS: 3 1:4,8,7,6 &‘ ‘E,i,E,7 ?L;
NOT? THIS CODE til NOT ARM OR DISARM AZR THE FOURTH DISARM.
@
. ,_ e:.-. ___ . ..-.. .
...-_ . . 1
. .A---. -.--.-- -- . -- -__ _ ‘__ - -. . ._ .- -- _-----
‘TT IS NOT NEC’5AkY TO DO ANY FURT:Ek PROGRAMMING AT THS POINT UNLZS
TIE PROM ?.RCGRAMM% STARTUP EXIT AND EhrI-RANCE TIME !S NOT ACEPTABLE
“. m Iv’iUSJ E RZ.PROGRhMED.
.-.. \

-..:
i .
.’
a-
. .
. w:
-_---
-.
*. STEP I: L’ tie Prom Programmed STARTUP EXIT. TIME is not acceptable, it
may berepr&
grammed at rius time ‘as follows: This i&uction manual assumes an example User
One code of 1,4.8,7,6. US%R-ohI DEL R,
D =CS: m 1 ~3.7.6 men depress 8, followed
_ ~
by any TWO(2) numbers on the keypad not to exceed ?5. THE NEW EXIT. TIME will
be TEN TIMES that number. . _ -..-. .--
EXAMPLE: 02 = 20 seconds
.NOl-E: 90 SECONDS CAN NOT BE PROGRAMMED.
STEP 3: If the Prom Programmed STABTUP’ENTRAN~E TIME is not accep&le,.jLmay\
be reprogrammed, at, this .time as foUows: This instruction manual
as&me.. /
an example User One code of 1,4,6,7,6. USER ONE DEPRESS: B ,1,4,8r716 ‘I.
then depress 9, followed by any two (2) numbers on the keypad not to
exceed 15. THE NEW. ENTRANCE TIME will be TEN TIMES rhat number.
EXAMPeE.: 02 ~‘20 seconds.
NOTE:’ 90 SECONDS CAN NOT BE PROGRAMMED. _.
There is .a built in SOUNDER on all OMNII 3000R’keypads that will annunciate as follows:{, _
A) A momen-tary BEEP on keypress to indicate successful entry
of all keys,
B) Constant steady BUZZ to indicate ENTRY time-
C) SeveraL pulsing BEEPS (7 or 8) to indicate a successful trans-
mission TOtne central office. This learure is called
SONALERT RINGBACK.
D) Pu!sing or steady to indicate violation’on any prom programmed.24H.R
TROUBLE ZONE.
SYSTEM NOTE 1:
SYSTEM N3TE i:
<I
.. SYSi3vl NOiZ 3:
,
SYSTEM NOTE 4:
There will be no sonalert.ringback on keypad AMBUSH o:SILEfl~.
KEYPAD PANIC.
‘If Dialer -transmission to the central office is unsuccessful
her the prom programmed number of attempts, the RED ARMED!
LED will blink slowly. This condition can be reset by oper- .
ation of iile Bburron. ._.
_. - _ --
L’ tne-OMNJ 3000 System ever Jose; toid power ‘AC and DC, ii _ !
will repowerup as ‘pe- extension digit programming. Regard- j
less of which state this system powers back up in, when the :
OMNI 3000.5y,sem finally reaches the disarmed state‘ (after ‘--i --reoowerup) it may be B%IY .for approximately IO-15 seconds :
reioading all User Codes. The system .will disregar.d aLl corn-- ’
mands 3or thai duration. *
. .- - --. -. . _..- - _ _ ..-
If the USER ONE CODE is ever.misrakenly programmed or- . :
f org,otten, a total system RESTART will be mandatory as foi.lowS~’
POWER DOWN THE OMNI 3000S\/STEM (AC AND DC!. POWER’
UP AGAIN AND DEPRESS THE KEYPADB WON 7wO (2)
TIMES WITHIN 30 SEC3NDS OF THE REPOWERUP. POWER
DOWN AGAIN- POWER ‘UP AGAIN. TtIE OMNI 3000 SYSTEM
IS BACK IN THE STARTUP MODE USER ONE MAY REPRO-
GRAM HIS AND ANY O-I-R CODE AS PREVIOUSLY EX-
PLAINED WITH THE STARTUP CODE BEEINNING‘ WITH SE? A.
I .
-.

. -KEYPAD .MOUNTING DIAGR’AM
.-..-
.
.._ _ . .