Profelmnet 3029 User manual

Ag.Dimitriou 286A ,173 42 Agios Dimitrios
Τηλ. Κέντρο: 210 9850 244, Fax: [phone]
www.profelmnet.com
3029
Control panel for rolling shutters up to 1200watt
Code
Frequency
Codification
Terminal
Switches
Photocells
Ext.Button
Auto close
Light
230V
Motor
torque
Slow move
Reverse
move
Memory
PSR/PTR - 3029
433,92/868,3
Keeloq Rolling
YES
YES
YES
YES
YES
NO
NO
YES
300
PS-3029
433,92
Standard
YES
YES
YES
YES
YES
NO
NO
YES
300
PN-3029
433,92
Profelmnet
Rolling
YES
YES
YES
YES
YES
NO
NO
YES
300
Νο
Function description
1
Not used
2
Not used
3
AUTO-CLOSE FUNCTION
OFF: No auto close
ON: Auto-close. Embedded auto close function. Works with the photocell.
When the gate opens and there is no access (no obstacle detection from the
photocell), the A/C time is 120 seconds (the gate will close after 120
seconds). If there is access and obstacle detection from the photocell, then
the A/C time is 10 seconds (the A/C timer counts 10 seconds after the
photocell is free and then the gate will automatically close). The second time
of A/C can be changed (follow the below instructions).
4
Not used.
5
PHOTOCELLS
OFF: NO photocells.
ON: Photocells. The power supply of the photocell 24VAC in terminals
13&14 and COM & NC of the photocell in terminals 8 & 9.
6
Not used
7
MOTOR REVERSION
OFF/ON: The first move of the motor needs to be opening, after the power
of control panel. When the first move is closure, switch the dipswitch 7 to
the opposite position.
8
Not used
Covering distance: from 30 –100 μ. depends on external conditions.
Check all connections. Check the terminal switches of the motor. The BLUE/GREY (common) motor wire is connected in terminal 4. Earth motor wire is not
connected in the control panel.
PHOTOCELL
TRANSFORMER
V - 1,5VA12 TRANSFORMER
24V - 1,5VA
CODE ΧΡΟΝ ΟΣ
REEIVER
PROGRAMMS
1 2 3 4 5 6 7 8
ON
FUSE5Α
RECEIVER RF
FLASH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
M
L I V E
NEUTRAL
COMMON
START/STOP
PHOTO
ANTENNA
OPEN CLOSE
230VAC 24VAC
60mA
COMMON
230V

Ag.Dimitriou 286A ,173 42 Agios Dimitrios
Τηλ. Κέντρο: 210 9850 244, Fax: [phone]
www.profelmnet.com
Functions and connections
Power supply 230V:
Supply the control panel with
230Vac.Check that the yellow
indication light is ON. Press the
button of the transmitter and
check the red indication light is
ON (receiver).
Clear memory:
The first step is to clear the
control panel memory. Press the
button CODE of the control panel
and the RED indication light goes
ON after a while. Keep it pressed
until the RED indication light goes
OFF. The memory is now clear.
Adding a new transmitter
with the control panel
button:
Press the CODE button and the
RED indication light goes ON (after a small delay). Leave it and during the next
3 seconds, press the desired transmitter channel button until the RED
indication light blinks and goes OFF. The new transmitter is saved. Follow the
same procedure to program more (up to 300) new transmitters.
Working time:
Adjustable from 1-180S. While the gate is fully closed, press and keep the
TIME button of the control panel pressed until the gate goes to fully open
position. Then leave it. The working time is saved.
Adding a new transmitter remotely:
The motor is fully closed or open. Press a working transmitter button (already
in memory) to start the motor working and hold it pressed until the motor
stops. When it stops, leave it and press the new transmitter button
immediately. The new transmitter is saved. Repeat steps to program more
transmitters remotely. When the memory is full (300 transmitters) you cannot
add more new transmitters.
Pedestrian function:
When the pedestrian traverses the gate, the gate will open for a while and then
automatically will close. Photocells need to be installed. The time of closing is
the same with the second time of A/C.
Photo-cell connection:
Connect the photocell contact and power supply 24VAC according to the
diagram in the right. When you finish, put the program dipswitch 5 in ON
position.
Photocell operation: When
the door closes and the photocell
beam is cut-off, the door stops
immediately and automatically
activates the open function. If the
photocell beam is cut-off, the door
never closes.
Blinker light function:
The blinker light gives a permanent voltage of 230V / 10W, connects to
terminals 1 & 3 and operates as long as the gate is moving. If you want to
flashes for more time, eg 100 seconds, then program 100-second for the
working time of the control panel.
Adjusting the auto close time:
There is a double counter in the A/C function. The first one is 120 seconds
and is applied when the door stops after an open function. During this
counting time of 120 sec., if the photocell beam is disturbed, then after the
beam is free, the A/C counting time becomes 10 sec. until the fully closed
position. In this control panel, the second counting time of 10 sec., can be
regulated. Press the TIME button, keep it pressed and within 1 sec. , press
the CODE button. The red indicating light starts flashing, indicating the
seconds of the counter. The time of the counter is from 1-120 seconds. Keep
it pressed for the time you wish to give in A/C and pedestrian function. The
dipswitch 3 needs to be ON.
Indication light LED:
There are indication LED lights that displays the different functions of the
control panel for the photocells.
Reset the automation:
Case of malfunction, please remove the power supply (230Vac) for 10
seconds, reconnect and recheck.
Compatible transmitters:
Based on the model you have, select the appropriate transmitter.