Feider Machines FBVES2800-UK User manual

ORIGINAL INSTRUCTIONS
SHREDDER
FBVES2800-UK
USER GUIDE
CAUTION: Read the instructions before using this machine.

CONTENET
1. SAFETY INSTRUCTIONS 3
2. EXPLANATION OF SYMBOLS 13
3. PARTS LIST 14
4. CHARACTERISTICS 14
5. GETTING STARTED 15
6. OPERATION 16
7. MAINTENANCE AND STORAGE 18
8. DECLARATION OF CONFORMITY 19
9. WARRANTY 20
10. PRODUCT FAILURE 21
11. WARRANTY EXCLUSIONS 22
WARNING: Read thoroughly the instruction manual before use

1. SAFETY INSTRUCTIONS
Before using this product, carefully read and
understand all the safety recommendations and
instructions for safe operation.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Keep this manual handy so that you may refer to it
later whenever any questions arise.
Always be sure to include this manual when selling,
lending, or otherwise transferring the ownership of this
product.
IMPORTANT! This product should only be used
by experienced users, who have thoroughly read
this instruction manual.
Only persons who have received adequate instructions
should use the product.
Never allow children, persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge or people unfamiliar
with these instructions to use the machine.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children.
Never allow children or persons unfamiliar with these
instructions to use the product
1.1- General safety instructions
Read the instructions carefully. Be familiar with the
controls and the proper use of the appliance
- For safe operation
3

1. Never operate this product when you are
fatigued, ill, or upset, or under the influence of
medication that may make you drowsy, or if you
are under the influence of alcohol or drugs. Keep
in mind, that the operator or user is responsible
for accidents or hazards occurring to other
people or their property.
2. Wear personnel protective equipment: gloves;
safety footwear, snug fitting clothing, goggles or
face protection, hearing and head protection
devices.
Use vibration-proof gloves.
3. Never allow people unfamiliar with these
instructions to use the appliance. Local
regulations may restrict the age of the operator.
Never operate the appliance while people,
especially children, or pets are nearby. Do not
start or use the product when persons are
nearby.
Keep bystanders (esp. children) and animals out
of the work area. Children, pets and bystanders
should be kept away when you start or operate
the product
Keep children away.
The use of this product by children is forbidden.
Keep the product away from children or from
their environment.
Children should be supervised to ensure that
they do not play with the product.
Never leave the product unattended especially
when children are nearby.
4

4. Never start working until you have a clear work area,
and secure footing,
5. Keep all parts of your body away from the feeding
opening when the engine is running.
6. Before you start the product, make sure the product
is properly assembled and that insertion chamber is
not obstructed.
7. All product service, other than the
maintenance listed in the Instructions Manual,
should be performed by competent service
personnel.
8. Always switch off the engine before carrying any
intervention.
9. Do NOT expose to and do not use during bad
weather conditions: never work in bad weather
(e.g. rain, storm, snow, high wind …), never work
when visibility is poor or in very high or low
temperatures. Never leave product outdoors
under the rain.
10. Keep the handles dry, clean and free of grease, oil
or fuel.
11. Operate the product only in outdoors or in well
ventilated areas.
12. Do not operate the product on slopes or any other
unstable location.
13.1. Become familiar with the controls and the proper
use of the equipment.
13.2. Store idle machine. When not in use, product
should be stored in a dry, locked up place, out of reach
of children.
13.3. Do not force the tool.
5

It will do the job better and safer at the rate speed for
which it is intended.
The product will do a better and safer job if it is used
only for the purposes it was designed for.
13.4. Remove adjusting keys and wrenches
Form the habit of checking to see that keys and
adjusting wrenches are removed from the machine
before operating it.
13.5. Defective switches or other part that is damaged
should be properly repaired or replaced by an
authorized service centre. Do not use the machine if
the switch does not turn it on and off.
13.6. Warning
The use of any accessory or attachment, other than
those recommended in this instruction manual, may
present a risk of injury to persons or animals and may
cause damages.
The user or operator is solely responsible for accidents
or hazards or any damages or injury caused to
properties and/or persons and/or animals.
The user/operator is responsible for the safety of third
persons present or entering the work area.
13.7. Remarks
The safety precautions and instructions given in this
manual are unable to cover in detail all the conditions
and situations that may arise.
The operator and/or user must use common sense
and caution when operating the product especially for
any matters that are not referred in the above
1.2- Safety precautions
6

1.2.1- Initial preparation before operation
- When you operate the machine, always wear full-length
trousers, as well as sturdy, closed footwear that provide
good support. Do NOT operate the machine wearing
shorts, when barefoot or wearing open sandals!
- Do not wear loose clothing or jewellery that can be
drawn into the inlet. Keep long hair away from the inlet.
Under no circumstances should jewellery, any other body
ornamentation, or loose clothing be worn while operating
the tool as these items could be drawn into the suction
orifice. Avoid wearing clothing that is loose fitting or that
has hanging cords or ties.
When working outdoors, rubber gloves and non-slip
footwear should always be worn.
If you have long hair, put it in a hair net.
- Wear protective equipment and always wear protective
goggles while operating the tool.
Wearing protective equipment such as a dust mask,
non-slip footwear, protective gloves, a helmet and/or
hearing protection (depending on the type and application
of the electrical device concerned) reduces the risk of
injury.
- When performing work that generates dust, wear a dust
protective mask to prevent dust irritation.
- Each time before you use the machine, check the
integrity of the product’s power cord and your own
extension cord for signs of damage and ageing. Do not
use the machine if the cord is damaged or worn. The
product should only be operated when its accessories are
in perfect working order.
7

Any damaged or defective components should be
repaired immediately by a qualified technician. Never
attempt to use an incomplete, not fully assembled or
modified machine.
- Under no circumstances or if safety equipment such as
collection box is not installed, before using, always
visually inspect to see, that the shredding means,
shredding means bolts and other fasteners are secure,
the housing is undamaged and that guards and screens
are in place. Replace worn or damaged components in
sets to preserve balance. Replace damaged or
unreadable labels.
- Only use a weather proof extension cable fitted with
coupler to IEC 60320-2-3.
Only extension cords that are rated for outdoor use
should be used outdoors.
Any extension cord used should have a minimum cross
section of not light than H07RN-F 2x1.5mm2.
1.2.2- During use
- Before starting the machine, make certain that the
feeding chamber is empty. Do not allow hands or any
other part of the body or clothing inside the feeding
chamber, discharge chute, or near any moving part.
- Always direct the cable to the rear away from the
appliance. Make sure the power cord is kept behind and
away from the device while you work.
- If the power cord or extension cord becomes damaged
during use, disconnect the supply cord from the mains
immediately. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY CORD FROM ITS
8

POWER SOURCE.
- If the supply cord is damaged, it must be replaced by a
special cord or assembly available from the manufacturer
or its service agent.
- Do not carry the appliance by the cable. Never use the
power cord as a handle to lift or carry the device.
- Always disconnect the product from the mains supply in
the following circumstances:
. whenever you leave the machines; when the machine
is not in use, is being carried/transported, or is left
unattended.
. before clearing a blockage; while examining, cleaning
or unclogging the product.
. before checking, cleaning or working on the product,
performing maintenance on it, or attaching accessories to
it.
. If the cutting device strikes a foreign object (e.g. small
stone, piece of metal…) or starts to vibrate abnormally.
- Use the machine in daylight or with adequate
illumination (good artificial light).
- Keep proper balance and footing at all times. Do not
overreach. Never stand at a higher level than the base of
the machine when feeding material into it.
- Bear in mind that the force generated by an electrical
device can make you lose your balance. Therefore, make
sure that your feet are firmly planted and that your body is
well balanced when you are operating the product.
- Never operate the machine on damp areas or wet grass.
- Do NOT use the machine on slope areas.
- Keep the chute outlet and ventilation holes (cooling air
inlets) unobstructed, clear of debris and clean at all times.
9

- Do not assume of your knowledge of the machine.
Remember that a split second of negligence is sufficient
to cause serious damage. Be aware of your surroundings
and stay alert for potential hazards that you may not hear
while operating the product.
- Keep a safe distance from the ejection zone when
working with the tool.
- Be especially careful that material contains no metal
parts, stones, bottles, cans or other foreign objects before
inserting into the tool.
- If the cutting mechanism strikes any foreign objects or if
the machine should start making any unusual noise or
vibration, immediately shut off the power source and
allow the machine to stop. Disconnect the machine from
the supply and take the following steps before restarting
and operating the machine:
i) inspect for damage;
ii) replace or repair any damaged parts;
iii) check for and tighten any loose parts.
- If the machine becomes clogged, shut-off the power
source and disconnect the machine from supply before
cleaning debris.
Never operate the machine with defective guards or
shields, or without safety devices, for example debris
collector in place.
Keep the power source clean of debris and other
accumulations to prevent damage to the power source
or possible fire.
Do not transport this machine while the power source is
running.
10

Stop the machine, and remove plug from the socket.
Make sure that all moving parts have come to a complete
stop
- whenever you leave the machine,
- before clearing blockages or unclogging chute,
- before checking, cleaning or working on the machine.
Do not tilt the machine while the power source is
running.
1.2.3- Before maintenance and storage
- When the machine is stopped for servicing, inspection, or
storage, or to change an accessory, shut off the power
source, disconnect the machine from the supply and make
sure that all moving parts are come to a complete stop.
Allow the machine to cool before making any inspections,
adjustments, etc. Maintain the machine with care and
keep it clean.
Always allow the machine to cool before storing.
When servicing the shredding means be aware that, even
though the power source is switched off due to the
interlock feature of the guard, the shredding means can
still be moved.
Never attempt to override the interlocked feature of the
guard.
- Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working condition.
- Check the debris collection box frequently for signs of
wear and/or deterioration.
- Replace any worn or damaged parts.
- Make sure to use only genuine/original replacement
parts and accessories.
11

- For reasons of safety, any worn or damaged component
should be replaced or repaired immediately by a qualified
technician.
- When not in use, store the machine only in a dry place
that is inaccessible to children.
1.2.4- Before starting the product
- Only operate the product after completely assembling it.
Do NOT operate product if it is not fully and properly
assembled!
- Before each use, check the machine for any signs of
damage.
- Prior to each use, check the power cord for signs of
damage. Under no circumstances should the power cord
be used if it shows any signs of damage.
- Ensure that the machine is only connected to
conventional sockets with a 230-240V alternating current
supply. Only use extension cables if they are really
necessary. The use of extension cables may cause a
drop in voltage, which will result in the machine not
performing to its peak or the motor overheating.
- The machine can be plugged into any 230-240 volt AC
outlet with 10 amps of fuse protection. The electrical
outlet is to be protected by an earth leakage circuit
breaker (ELCB) with a max triggering current of 30mA(i.e.
the appliance should be supplied via a Residual Current
Device (RCD) with a tripping current of not more than
30mA).
12

2. EXPLANATION OF SYMBOLS
Do not expose to weather conditions (ex.: rain, snow …) or to moisture.
Do not use nor leave outdoor during weather conditions (e.g. rain, snow…)
Do not use in the rain or leave outdoors while it is raining.
Caution! Risk of injury and/or damage and/or deterioration of product in case on
non-compliance to safety requirements.
Read the instructions manual.
Class II product with double or reinforced insulation
Wear eye protection.
Wear ear protection.
The machine may exceed 85 dB(A) at the workplace; in this case, noise protection
measures need to be taken to protect the user.
Wear protective gloves and shoes with non-slippery sole.
Keep all parts of your body away from moving parts and from the shredder
opening.
Rotating cutting knife. Keep hands and feet away from the openings while tool is
running.
Do not step on the collection box.
Keep persons (esp. children) and animals away from product and working area.
Projection hazard (e.g. small debris).
Keep bystanders at a safe distance (at least 3m) away from the tool while in
operation.
Let moving parts come to a standstill before carrying any intervention on machine.
Locked and unlocked position
Cutting diameter adjustment
Disconnect product from its power source before maintenance, cleaning or any
intervention on product; when you do not use product or when you leave it
unattended for any period.
Disconnect product from its main power source, if product, power cable, or
extension cord is damaged or cut during operation.
Unplug product by pulling the plug. Do not pull the cable.
Do not dispose of this product with household rubbish. Dispose of this product in
the nearest recycle centre. Please contact your local authority or local recycle
centre for further information for its safe disposal.
Guarantee sound power level.
13

3. PARTS LIST
1- Push Stick
2- Feeding opening (feeding chamber)
3- Safety switch
4- Forward / Reverse mode switch
5- ON/OFF switch
6- Power cord anchoring device
7- Power cord & plug
8- Sliding rail
9- Lock button
10- Collection box
11- Support foot
12- Tubes (legs support tubes)
13- Wheel
14- Wheel cover
15- Counter plate adjusting knob
16- Back cover
17- Handle
Fig.1
4. CHARACTERISTICS
Voltage
230-240 V ~ 50 Hz
Power
2800 W (P40)
No load speed no
60 min-1
Insulation protection class
II
Ingress Protection
IP4
Operating cycle
P40-S6(40%) means 40s load and 60s idle time
operation model
Cutting diameter (max)
44 mm
Collection bag capacity
60 L
Sound Pressure Level (LPA)
Measured 79.1 dB (A) K = 3 dB(A)
Sound Power Level (LWA)
Measured 91.7 dB(A) K=2.67dB(A)
Guaranteed 94 dB(A)
Weight (approx.)
14.5 kg
14

5. GETTING STARTED
4.1- Unpacking
- Remove product from its packaging.
- Check that tool and accessories are not missing or damaged.
- If you find anything part missing or damaged, do not operate the tool until the part
has been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
4.2- Content
The unit package contains:
- Main unit
- 1 Collection box
- 1 Push stick
- Hex Wrench
- Instructions manual
4.3- Assembly
The machine requires some assembly prior to first time use.
This includes fitting the wheels, the tubes (support feet) to the housing and collection box.
4.3.1- Tubes (Support Feet, see Fig.2)
Turn the shredder upside down and pivot the tubes (support feet) upward.
Insert the supplied wheel axle (A) through the respective openings of each tube.
4.3.2- Wheels (Fig.3)
Put the supplied washer (B) and sleeve (C) onto the wheel axle (A) (Fig. 3B)
Place the wheels (D) and tighten nut (E) by hand (Fig. 3C).
Using the supplied hex wrench (F), fix the wheel axle and at the same time firmly tighten the nut by using a
wrench (not supplied) (G). (Fig. 3D)
Finally, place the wheel cover (H) in the center of the wheel. (Fig. 3E)
Fig.2
Fig.3a
Fig.3b
Fig.3c
Fig.3d
Fig.3e
Turn the shredder back on its stand and wheels.
ATTENTION: Take care when turning the unit onto its wheels as the unit has an uneven weight
distribution.
15

4.3.3- Collection box (Fig.4)
To insert the collection box:
Press down the lock button (A).
Then insert the collection box into the sliding rails (8).
Press the lock button (A) upward.
To remove the collection box:
Press down the lock button (A).
Then slide the collection box out of the undercarriage.
Note: Before you remove and empty the collection box, ensure
that the machine has been disconnected from its power supply.
Fig.4
4.4- Start and Stop (Fig.5)
To Start the machine:
Press the Forward/Reverse switch (A) to FORWARD
position.
Press the On/Off switch (B) to (I) ON position to start the motor.
To Stop the machine:
Press the On/Off switch (B) to (O) OFF position to stop the motor.
Fig.5
4.5- Overload protection (Fig.5)
This machine is equipped with an overload protection system, to protect the motor from being damaged. The
safety switch will automatically switch off the power when the motor is overloaded.
Wait for at least 1 minute before restarting by first pressing the reset button and then the On/Off switch.
If the motor does not restart, do the following (wear safety gloves) :
1. Press the safety switch (C).
2. Press the Forward/Reverse switch (A) to REVERSE position.
3. Press and hold the On/Off switch (B) to (I) ON position to remove any objects that could obstruct the blades.
6. OPERATION
5.1- Intended use
- The product is intended for outdoor domestic use in private gardens.
- The product is designed to shred garden debris such as clippings and small twigs within the limits of its
characteristics (smaller than 40mm in diameter).
It is not to be used for any other purpose outside of the described scope in this manual.
- It is recommended to use the product only on dry surfaces, do NOT operate on damp or wet working area.
- Do not use the machine for unsuitable purposes (for ex. for shredding other materials such as plastic, paper;
metal…)
- The tool is not intended for artisanal, commercial, professional or industrial use (ex.: in public parks…).
5.2- Operation
BEFORE any operation:
-- Always visually inspect that the product does not show signs of use or damage. Replace any used or
damaged part.
-- Check that the screws, bolts and nuts are well tightened. Tighten firmly the screws, bolts and nuts when
needed.
-- Ensure that the collection box is properly and securely installed.
-- Ensure that the machine is only connected to conventional sockets with a 230-240V alternating current
supply.
-- Only use extension cables, if they are really necessary, intended for outdoor use and approved.
The use of extension cables may cause a drop in voltage, which will result in the machine not performing to its
peak or the motor overheating.
-- Look into the feeding chamber to make sure it is empty. Do NOT start machine before clearing any material
still present in the feeding chamber.
DURING operation
16

-- Keep proper balance and footing at all times. Do not over reach. Never stand at a higher level than the base
of the machine, when feeding material into it.
-- Always keep your fingers and hands away from the feeding chamber. Use the push stick to push in the
material.
--When feeding material into the machine be extremely careful that pieces of metal, rocks, glass bottles, cans
or other foreign objects are not included.
-- If the cutting mechanism strikes any foreign objects or if the machine should start making any unusual noise
or vibration, switch off the machine and allow it to come to a complete stop, disconnect the plug from the power
source, and take the following steps:
- Inspect the machine for damage.
- Check for and tighten any loose parts.
- Have any damaged parts replaced or repaired by an authorized service center with original parts.
-- Always stand clear of the discharge zone when operating this machine.
Do not allow processed material to build up in the discharge zone; this may prevent proper discharge and can
result kickback of material through the feed intake opening. Empty the collection box regularly.
-- Do not transport this machine while the power source is running.
-- Switch off the machine and disconnect the plug from its power source whenever you leave the work area.
-- Do not tilt the machine while in operation.
-- Motor should be kept clean of debris and other accumulations.
5.2.1- Power cord plugging
Plug the power plug into an approved electrical extension cord, and loop the extension cord around the power
cord anchoring hook.
Connect the extension cord plug to power supply.
Tip: The extension cord may come undone from the power cord during use. To avoid this, use the cable
restraint (9).
5.2.2- To switch ON and OFF
See 4.4.
Important : After you have switched off the machine, do not leave it unattended while still connected to the
electrical supply. Unplug from mains and store product.
5.2.3- Use.
1. Insert the material to be shredded into the opening (feeding chamber) on the right side.
It will be automatically drawn into the machine by the cutter as it turns anticlockwise.
2. Do not stuff the opening completely full to avoid jamming the machine.
3. Alternate feeding branches and small litter that is a bit wet and decomposed. This will also help to avoid
jamming the cutter.
4. Squashy kitchen rubbish must be composted, never put it through the shredder!
5. Branches with leaves must always be entirely through the shredder and out of the way before feeding new
material into the machine. Make sure the shredded material is able to fall unobstructed into the collection box
without blocking the outlet.
6. The ventilation opening must not be locked by the shredded material.
7. Continuous shredding of thick wood or branches can cause the machine to jam.
8. Soft material like leaves or sprigs can easily block the inlet; use a push stick to poke it in.
9. Always check litter for nails and stones before shredding as they can seriously damage the shredder.
10. For better performance and comfort, it is recommended to empty the collection box regularly (for ex. when
it reaches 2/3rd of its capacity).
Tips for shredding:
Depending on the type, age and dryness of the wood, branches will be more or less easily shredded.
The best results are obtained when fresh branches are shredded shortly after being cut.
It is recommended to shred soft garden waste in small quantity, especially when the waste is wet. You can
avoid blockage by performing periodic shredding sessions.
5.2.4 –Adjusting the counter plate
To obtain an optimum shredding result and prevent damage to the blade, the counter plate must be adjusted at
regular intervals.
The counter plate must also be adjusted when so called interlinkage occurs.
1. Turn counter plate adjusting knob (A) clockwise until a slight friction noise can be heard and fine aluminum
chips fall from the ejector chute for a short period of time.
2. Then, the materials to be shredded should be fully cut again.
17

5.2.5- Replacing the counter plate
1. Open the back cover by loosening the 4 Screws (A).
2. Take out the counter plate (B) and replace with a new one.
3. Put back the back cover and tighten the 4 screws.
7. MAINTENANCE AND STORAGE
Before any intervention on product, ensure that product is disconnected from its power
source.
Reminder: Make sure to maintain the machine in good working condition, carry out regular maintenance of the
machine after each use and before storage. Any breach or default of adequate maintenance reduces the life of
the machine and increases the risk of breakdowns and accidents.
To preserve the security system throughout the life of the machine, it is important to perform maintenance and
proper cleaning, DO NOT use non-compliant replacement parts and do NOT dismantle yourself the machine
or change the security features.
6.1- After using the machine
1) Empty the collection box.
2) Check the machine (feeding inlet and chute) and remove material residue.
6.2- Cleaning
Clean plastic parts with a soft and clean cloth
Do not use aggressive cleansers (solvents or abrasive cleansers), or an abrasive sponge.
Do not use any caustic to clean the plastic parts.
Do not put or immerse machine in water or any other liquid, and ensure that no water gets inside the machine.
Do not clean the machine with running water or high pressure.
6.3- Storage
Clean product and empty the collection box.
Store product, instructions manual and accessories in its original packaging.
Product must be stored in a clean, dry location. Always lock up product and keep out of reach of children.
Do not store product in temperatures lower than 0ºC (32ºF)
Do not place or store any object on top of the product.
18

6.4- Disposal
- Debris & remnants: do not throw with household rubbish or in the environment. Dispose of any debris and
remnants in rubbish collection centres or seek advice from your local municipality.
- Machine: do not dispose with household garbage. Do not throw into the environment.
Dispose of the product in a collection centre for waste of electrical and electronic equipment, or a waste
drop-off centre; or seek advice from your local municipality.
- Proceed with disposal of remnants, machine, accessories and packaging according to local regulations
regarding the protection of the environment.
8. DECLARATION OF CONFORMITY
BUILDER SAS
ZI, 32 rue Aristide Bergès –31270 Cugnaux - France
Declares that the machinery designated below:
Silent shredder
FBVES2800-UK
Serial number: 20210734420-20210734669
Complies with the provisions of the Directive “machinery” 2006/42/EC and national laws transposing it:
Also complies with the following European directives:
EMC Directive 2014/30/EU
ROHS Directive 2011/65/EU+2015/863/EU
Noise directive 2004/14/EC and 2005/88/EC
Sound power level - measured: 91.7 dB(A) K = 2.67 dB(A)
Guaranteed: 94 dB(A)
Also complies with European standards, with national standards and the following technical provisions:
Responsible for the technical file: M. Olivier Patriarca
Cugnaux, on 12/05/2021
Philippe MARIE / PDG
19

WARRANTY
The manufacturer guarantees the product against defects in material and workmanship for a period of 2
years from the date of the original purchase. The warranty only applies if the product is for household use.
The warranty does not cover breakdowns due to normal wear and tear.
The manufacturer agrees to replace parts identifed as defective by the designated distributor. The
manufacturer does not accept responsibility for the replacement of the machine, in whole or in part , and/or
ensuing damage.
The warranty does not cover breakdowns due to:
• insufcient maintenance.
• abnormal assembly, adjustment or operations of the product.
• parts subject to normal wear and tear.
The warranty does not extend to:
• shipping and packaging costs.
• using the tool for a purpose other than that for which it was designed.
• the use and maintenance of the machine done in a manner not described in the user manual.
Due to our policy of continuous product improvement, we reserve the right to alter or change specifcations
without notice. Consequently, the product may be diferent from the information contained therein, but a
modifcation will be undertaken without notice if it is recognized as an improvement of the preceding
characteristic.
READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.
When ordering spare parts, please indicate the part number or code, you can fnd this in the spare parts list
in this manual. Keep the purchase receipt; without it, the warranty is invalid. To help you with your product,
we invite you to contact us by phone or via our website:
• +33 (0)9.70.75.30.30
• https://services.swap-europe.com/contact
You must create a "ticket" via the web platform.
• Register or create your account.
• Indicate the reference of the tool.
• Choose the subject of your request.
• Describe your problem.
• Attach these fles: invoice or sales receipt, photo
of the identifcation plate (serial number), photo
of the part you need (for example: pins on the
transformer plug which are broken).
9. WARRANTY
20