Duronic PS591 User manual

PS591

2

3
Creative Consumer Products
English Manual
Manuel d’utilisation en français
Gebrauchsanleitung auf Deutsch
Manual de Instrucciones en Español
Manuale D’istruzioni In Italiano
Instrukcja obsługi. Polski
5
13
21
29
37
45
Contents

4

5
Creative Consumer Products
English Manual

6
SPECIFICATIONS
Shred Type: Crosscut
Shred Size: 4mm x 44mm
Shredding Capacity: 20 Sheets
Duty Cycle: 30 min ON / 40 min OFF
Feed Opening: 220mm
Input: 220 - 240V, 50-60Hz, 2A

7
Creative Consumer Products
1. e PS591 shredder should be placed on a at, level surface.
2. Carefully place the shredder into the upright position on a at level surface.
3. Be careful not to place your ngers near the cutter blades.
4. With the wastebasket removed from the shredder, place the shredder head over the
cabinet, then rmly push down on the four corners of the shredder head to lock it
into place.
5. Slide the wastebasket into the shredder cabinet. Make sure that the wastebasket is
completely inserted into the shredder and that it ts ush with the cabinet.
6. Plug the power cord into any standard 230-Volt AC outlet which shall be installed
near the equipment and should be easily accessible.
7. Place the switch in the AUTO position. e READY LED should light up. You are
now ready to start shredding.
SETUP
OPERATION
With the electrical cord plugged in, the switch in the AUTO position and wastebasket
properly inplace the READY LED will light up. is signals that the shredder is now
ready for use. When the paper is inserted into the feed opening, the shredding process
will start automaticaly and stop when the paper has completed its travel through the
feed opening.
e PS591 mode selection switch is located on top of the shredder. Also located on top
of the shredder is the READY LED light.
•AUTO: e shredding process will start when the paper is inserted into the feed
ioening and will continue until it has completely passed through.
• REV: In the event of a paper jam, this reverses the shredding process in order to
assist in the removal of a paper jam. us clearing the cutters.
•OFF: It is recommended to turn the shredder o when it is not being used for a
prolonged period of time.
• READY: When the READY LED is lit up, it lets the user know that the wastebasket
is correctly inserted and the shredder is on and ready for use. If the READY LED

8
e PS591 will shred up to 20 sheets up paper and will accept paper widths up to
220mm. When shredding envelopes or receipts, insert them into the middle of the feed
opening. CD’s, DVD’s and credit cards should be placed in the designated slot.
PAPER JAMS AND OVERLOADS
e PS591 is equipped with an automatic motor overload protection circuit. e duty
cycle for the PS591 is rated for 30 Min ON / 40 Min OFF. e PS591 will automatically
terminate power in case of the following situations.
1. Operating the shredder at the maximum capacity of twenty (20) sheets
continuously for a prolonged period of time.
2. Exceeding the shredding capacity by inserting more than 20 sheets of paper in one
pass or if the paper is not fed squarely into the feed opening.
Both abnormal operations may result in the activation of the automatic thermal motor
overload protection circuit, which terminates the power to the shredder. A paper jam
could cause the thermal motor overload protection to terminate AC to power the
motor. Never allow the shredder to remain in a jammed condition with the AC power
turned on. If this occurs you should:
In case of a minor paper jam:
1. Grasp the excess paper from the top and pull it out as you depress the REV button.
does not light up, make sure the shredder is plugged in and the wastebasket is
inserted correctly.
• FULL: e PS591 has a basket full sensor to detect when it needs empying.
CAPACITY

9
Creative Consumer Products
Be careful not to place your ngers near the feed opening or else serious harm
could occur.
2. Make sure that all of the excess paper has been removed from the feed opening.
3. You are now ready to resume normal shredding.
In case of a major paper jam:
1. Turn o or unplug the power cord from the AC outlet and wait at least 40 minutes
for the thernal overload protection to reset.
2. Plug in the AC power cord and place the switch back into the AUTO position.
If paper was le inside the feed opening prior to the overload, place the switch
in REV and grasp the excess paper from the top and pull it out. Be careful not to
place your ngers near the feed opening or serious harm could occur.
3. Place the switch back into the AUTO position. You are now ready to resume
normal shredding.
SAFETY INFORMATION
BEFORE USE
• Dispose of all packaging carefully and responsibly.
• is appliance is designed for indoor use only. Do not use outdoors.
• Do not use this shredder for industrial and commercial use, or any other purpose.
• e shredder MUST be positioned on a rm level base before and during use.
• Ensure the power cable is not caught under the appliance.
• Ensure the correct power supply is used (230V AC).
• Keep power cord away from hot surfaces.
• Do not place the shredder near a heat source or in direct sunlight.
• Do not operate under or near curtains or other combustible materials.
• Do not immerse the machine in water or any other liquid to protect against
electric shock.
• Keep out of reach of children.
• Do not spray any ammable synthetic oil, petroleum-based or aerosol products
onto this shredder as it may cause a re.
• Do not allow the shredder to be exposed to rain or any other moisture.
Important - Please read these instructions fully before installation

10
DURING USE
• WARNING! Keep loose articles of clothing; ties, jewellery, hair or other objects
away from the feed opening in order to prevent injury.
• Never insert ngers into the feed opening. Serious injury may result!
• is appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
• Do not leave children unattended with the shredder.
• ALWAYS keep the shredder o and unplugged when not in use.
• DO NOT attempt to feed more sheets of paper into the feeder than specied.
• ALWAYS limit continuous shredding to the specied time as suggested in the
instruction manual.
• DO NOT attempt to shred materials other than paper and credit cards in the
provided feed slot.
• To avoid overheating the shredder, limit continuous shredding to the specied
time as suggested in this instruction manual.
• Do not operate the shredder if the cord or plug are damaged or if the shredder has
malfunctioned in any way.
• ALWAYS unplug the shredder when moving, cleaning or emptying the
wastebasket.
• DO NOT attempt to operate the shredder if the shredder is experiencing any kind
of problem.
• If your machine stops working, do not attempt to repair it yourself! Contact
Duronic (Shine-Mart) for assistance.

11
Creative Consumer Products
• Never use any sharp instruments or abrasive substances, soap, household cleaner,
detergent or wax polish for cleaning.
• Never clean the appliance with ammable uids. It could cause a damage and re
hazard.
• Use lukewarm water on a cloth to clean the cabinet and wastebasket of the
appliance and wipe it dry.
• Ensure the unit is dry before connect to the mains
WARNING READ INSTRUCTION
BEFORE USE
NO FINGERS
OR HANDS
NO HAIR
NO LOOSE
CLOTHING
NO CHILDREN NO AEROSOL
PRODUCTS
18 - 20
MAX
CLEANING AND MAINTENANCE
Important: Always unplug the appliance from the power socket during
cleaning and maintenance.

12
Warranty
1 Year Guarantee from Shine-Mart Ltd, Trademark owners of Duronic Products.
NOTE: THESE STATEMENTS DO NOT AFFECT YOUR STATUTORY RIGHTS AS A
CONSUMER
This product has been manufactured under the strictest or quality control procedures, and
using the highest quality of materials, to ensure excellent performance and reliability. It will
give very good and long lasting service, provided it is properly used and maintained. The
product is guaranteed for 1 years from the date of original purchase. If any defect arises due
to a faulty materials or poor workmanship, the faulty product must be returned to the original
place of purchase. Refund or replacement is at the discretion of that company.
Duronic Products are offered with a 1 year guarantee under the following conditions:
1. The product must be returned to the retailer with original proof of purchase.
2. The product must be installed and used in accordance with the instructions
contained in this operating manual.
3. It must be used only for domestic purposes.
4. It does not cover wear and tear, malicious damage, misuse, neglect,
inexpert repairs or consumable parts.
5. Shine-Mart Ltd has no responsibilities for accidental or consequential loss or damage.
6. Shine-Mart Ltd are not liable to carry out any type of servicing work,
under the guarantee
7. Valid in the UK only
This product is tted with CE:1363 plug and fuse
Imported by Shine-Mart Ltd, RM3 8SB
Information on waste Disposal for Consumers of
Electrical & Electronic Equipment.
This mark on a product and/or accompanying documents indicates that when it
is to be disposed of, it must be treated as Waste
Electrical & Electronic Equipment, (WEEE).
Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used.
For proper treatment, recovery and recycling; please take all WEEE marked
waste to your Local Authority Civic waste site,
where it will be accepted free of charge.
If customers dispose of Waste Electrical & Electronic Equipment correctly, they
will be helping to save valuable resources and preventing any potential negative
effects upon human health and the environment, of any hazardous materials that
the waste may contain.

13
Creative Consumer Products
Manuel d’utilisation en français

14
SPECIFICATIONS
Shred Type: Crosscut
Shred Size: 4mm x 44mm
Shredding Capacity: 20 Sheets
Duty Cycle: 30 min ON / 40 min OFF
Feed Opening: 220mm
Input: 220 - 240V, 50-60Hz, 2A

15
Creative Consumer Products
1. e PS591 shredder should be placed on a at, level surface.
2. Carefully place the shredder into the upright position on a at level surface.
3. Be careful not to place your ngers near the cutter blades.
4. With the wastebasket removed from the shredder, place the shredder head over the
cabinet, then rmly push down on the four corners of the shredder head to lock it
into place.
5. Slide the wastebasket into the shredder cabinet. Make sure that the wastebasket is
completely inserted into the shredder and that it ts ush with the cabinet.
6. Plug the power cord into any standard 230-Volt AC outlet which shall be installed
near the equipment and should be easily accessible.
7. Place the switch in the AUTO position. e READY LED should light up. You are
now ready to start shredding.
SETUP
OPERATION
With the electrical cord plugged in, the switch in the AUTO position and wastebasket
properly inplace the READY LED will light up. is signals that the shredder is now
ready for use. When the paper is inserted into the feed opening, the shredding process
will start automaticaly and stop when the paper has completed its travel through the
feed opening.
e PS591 mode selection switch is located on top of the shredder. Also located on top
of the shredder is the READY LED light.
•AUTO: e shredding process will start when the paper is inserted into the feed
ioening and will continue until it has completely passed through.
• REV: In the event of a paper jam, this reverses the shredding process in order to
assist in the removal of a paper jam. us clearing the cutters.
•OFF: It is recommended to turn the shredder o when it is not being used for a
prolonged period of time.
• READY: When the READY LED is lit up, it lets the user know that the wastebasket
is correctly inserted and the shredder is on and ready for use. If the READY LED

16
e PS591 will shred up to 20 sheets up paper and will accept paper widths up to
220mm. When shredding envelopes or receipts, insert them into the middle of the feed
opening. CD’s, DVD’s and credit cards should be placed in the designated slot.
PAPER JAMS AND OVERLOADS
e PS591 is equipped with an automatic motor overload protection circuit. e duty
cycle for the PS591 is rated for 30 Min ON / 40 Min OFF. e PS591 will automatically
terminate power in case of the following situations.
1. Operating the shredder at the maximum capacity of twenty (20) sheets
continuously for a prolonged period of time.
2. Exceeding the shredding capacity by inserting more than 20 sheets of paper in one
pass or if the paper is not fed squarely into the feed opening.
Both abnormal operations may result in the activation of the automatic thermal motor
overload protection circuit, which terminates the power to the shredder. A paper jam
could cause the thermal motor overload protection to terminate AC to power the
motor. Never allow the shredder to remain in a jammed condition with the AC power
turned on. If this occurs you should:
In case of a minor paper jam:
1. Grasp the excess paper from the top and pull it out as you depress the REV button.
does not light up, make sure the shredder is plugged in and the wastebasket is
inserted correctly.
• FULL: e PS591 has a basket full sensor to detect when it needs empying.
CAPACITY

17
Creative Consumer Products
Be careful not to place your ngers near the feed opening or else serious harm
could occur.
2. Make sure that all of the excess paper has been removed from the feed opening.
3. You are now ready to resume normal shredding.
In case of a major paper jam:
1. Turn o or unplug the power cord from the AC outlet and wait at least 40 minutes
for the thernal overload protection to reset.
2. Plug in the AC power cord and place the switch back into the AUTO position.
If paper was le inside the feed opening prior to the overload, place the switch
in REV and grasp the excess paper from the top and pull it out. Be careful not to
place your ngers near the feed opening or serious harm could occur.
3. Place the switch back into the AUTO position. You are now ready to resume
normal shredding.
SAFETY INFORMATION
BEFORE USE
• Dispose of all packaging carefully and responsibly.
• is appliance is designed for indoor use only. Do not use outdoors.
• Do not use this shredder for industrial and commercial use, or any other purpose.
• e shredder MUST be positioned on a rm level base before and during use.
• Ensure the power cable is not caught under the appliance.
• Ensure the correct power supply is used (230V AC).
• Keep power cord away from hot surfaces.
• Do not place the shredder near a heat source or in direct sunlight.
• Do not operate under or near curtains or other combustible materials.
• Do not immerse the machine in water or any other liquid to protect against
electric shock.
• Keep out of reach of children.
• Do not spray any ammable synthetic oil, petroleum-based or aerosol products
onto this shredder as it may cause a re.
• Do not allow the shredder to be exposed to rain or any other moisture.
Important - Please read these instructions fully before installation

18
DURING USE
• WARNING! Keep loose articles of clothing; ties, jewellery, hair or other objects
away from the feed opening in order to prevent injury.
• Never insert ngers into the feed opening. Serious injury may result!
• is appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
• Do not leave children unattended with the shredder.
• ALWAYS keep the shredder o and unplugged when not in use.
• DO NOT attempt to feed more sheets of paper into the feeder than specied.
• ALWAYS limit continuous shredding to the specied time as suggested in the
instruction manual.
• DO NOT attempt to shred materials other than paper and credit cards in the
provided feed slot.
• To avoid overheating the shredder, limit continuous shredding to the specied
time as suggested in this instruction manual.
• Do not operate the shredder if the cord or plug are damaged or if the shredder has
malfunctioned in any way.
• ALWAYS unplug the shredder when moving, cleaning or emptying the
wastebasket.
• DO NOT attempt to operate the shredder if the shredder is experiencing any kind
of problem.
• If your machine stops working, do not attempt to repair it yourself! Contact
Duronic (Shine-Mart) for assistance.

19
Creative Consumer Products
• Never use any sharp instruments or abrasive substances, soap, household cleaner,
detergent or wax polish for cleaning.
• Never clean the appliance with ammable uids. It could cause a damage and re
hazard.
• Use lukewarm water on a cloth to clean the cabinet and wastebasket of the
appliance and wipe it dry.
• Ensure the unit is dry before connect to the mains
WARNING READ INSTRUCTION
BEFORE USE
NO FINGERS
OR HANDS
NO HAIR
NO LOOSE
CLOTHING
NO CHILDREN NO AEROSOL
PRODUCTS
18 - 20
MAX
CLEANING AND MAINTENANCE
Important: Always unplug the appliance from the power socket during
cleaning and maintenance.

20
Garantie et service après-vente
1 an de garantie de la part de Shine-Mart Ltd, propriétaire de la marque Duronic.
NOTE : CES DÉCLARATIONS N’AFFECTENT EN RIEN VOTRE DROIT STATUTAIRE EN
TANT QUE CONSOMMATEUR
Ce produit a été produit en suivant les procédures de contrôle de qualité les plus strictes en
utilisant des matériaux de qualité pour assurer une excellente durabilité et performance.
Cette centrifugeuse vous offrira de longues années de service tant que vous utilisez
correctement cette machine et suivez les instructions de maintenance contenues dans ce
manuel. Ce produit est garanti pour 1 an à partir de la date originelle d’achat. Si ce produit
était endommagée en raison d’un problème électrique ou d’une fabrication imparfaite,
le produit défectueux peut être remplacé au vendeur à la discrétion de la marque sous
conditions:
1. Le produit doit être retourné avec la preuve originale d’achat.
2. Le produit doit être installé et utilisé en accord avec les instructions contenues
dans ce manuel d’utilisation.
3. Le produit doit être réservé à un usage privé.
4. La garantie ne protège pas contre les dommages dus à l’usure normale,
l’utilisation malveillante, la mauvaise utilisation, la négligence, les réparations
conduites par des non-experts ainsi que les pièces consommables.
5. Shine-Mart Ltd ne porte pas de responsabilité pour tout dommage ou perte
accidentel ou conséquent causé par ce produit.
6. Shine-Mart Ltd se dégage de toute responsabilité en matière de réparation
durant la période de garantie.
7. Valide dans toute l’Union Européenne.
Ce produit est fourni avec une prise européenne
et un fusible de 3 ampères.
Importé par Shine-Mart Ltd, RM3 8SB.
Ce symbole apparaît sur le produit et/ou les documents accompagnant ce
produit pour indiquer que pour procéder à la destruction de ce produit, celui-ci
doit être traité comme un déchet électrique et électronique (WEEE).
Les produits marqués WEEE ne doivent être mélangés avec les déchets
ménagers et doivent être séparés pour traitement et recyclage des composants.
An de traiter et recycler ce produit, veuillez déposer tous les composants
marqués WEEE au site de recyclage le plus proche où ce produit sera repris
gratuitement. Si les clients jettent les déchets électriques et électroniques
WEEE correctement, ce geste aidera la préservation de ressources précieuses
et prévient les potentiels effets négatifs que ces composants ou tout autre
composant dangereux ont sur la santé humaine et l’environnement.
Garantie
suivez nous
www.duronic.com @Duronic_FranceDuronic France@duronic_france