Fein KBE 35 User manual

KBE 35
Technical data
C-SC_CSSM
Version 1.0
2017-05-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Technical data
All the technical data can be found in the operating instructions for the model.
Tests
Up-to-date test data and test instructions after repair can be found on the FEIN Extranet (Customer Service → Repair Guides).
Lubricants / Auxiliary substances
The lubricants or auxiliary substances and their container sizes available from FEIN can be found on the FEIN Extranet
(Customer Service → Repair Guides).
Lists of spare parts
Lists of spare parts and exploded views are available online at www.fein.com

KBE 35
Notes and requirements
C-SC_CSSM
Version 1.0
2017-05-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Please note
These instructions are only intended for persons with suitable technical training. It is assumed that the reader has mechanical and
electrical training.
Only use original FEIN spare parts.
Provisions
Please note that power tools may only be repaired, maintained and checked by a trained electrician, as improper repair can result in
serious risks to the user.
The provisions set out in DIN VDE 0701-0702 should be observed after repairs.
The relevant accident prevention regulations of the employer’s liability insurance associations are to be observed when
commissioning.
The German Equipment and Product Safety Act [ProdSG] applies for correct use.
Outside Germany, the regulations applicable in the relevant country must be observed.

KBE 35
Lubricants and auxiliary substances required
C-SC_CSSM
Version 1.0
2017-05-02
All rights reserved by FEIN, especially in case of industrial rights registration.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Lubricants and auxiliary substances
Grease 0 401 18 0300 9 120 g gearbox

KBE 35
Troubleshooting
C-SC_CSSM
Version 1.0
2017-05-02
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 1
Not yet available.

KBE 35
Removal
C-SC_CSSM
Version 1.0
2016-05-20
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 1of 10
Removing the container
NOTE:
Fluid may be present in the container.
Drain the container (2) before removal.
1. Remove the hose (1) from the hose socket.
2. Remove the container (2).
2
1

KBE 35
Removal
C-SC_CSSM
Version 1.0
2016-05-20
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 2of 10
Removing the connecting cable
1. Unscrew the two screws (1).
2. Remove the lower part of the cover (2).
3. Unscrew the screw (3).
4. Remove the cable clamping piece (4).
5. Unscrew the two screws (5).
6. Remove the upper part of the cover (6).
7. Remove the two strands (7).
Tools:
- Torx T15
1
2
3
4
6
5
7
7

KBE 35
Removal
C-SC_CSSM
Version 1.0
2016-05-20
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 3of 10
Removing the drill motor
1. Unscrew the flat headed screw (1).
Crushing hazard around drill motor!
The drill motor will immediately slide downwards as soon as the screw (2) has been loosened.
First move the drill motor downwards and then unscrew the screw (2).
2. Move the drill motor downwards by turning the spider.
3. Unscrew the screw (2).
4. Slide the drill motor (3) out of the guide.
Tools:
- Slotted screwdriver
- Socket head wrench,
6 mm
1
2
3

KBE 35
Removal
C-SC_CSSM
Version 1.0
2016-05-20
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 4of 10
Removing the carbon brush holders (on both sides)
1. Lift up the spring (1).
2. Remove the carbon brush (2).
3. Pull off the plug (3).
4. Remove the carbon brush holder (4).
5. Remove the cable (5).
Tools:
- Assembly aid
- Long-nosed pliers
1
2
4
5
3

KBE 35
Removal
C-SC_CSSM
Version 1.0
2016-05-20
All rights reserved by FEIN, especially in case of property rights applications.
FEIN retains all rights of disposal, such as copying and circulation.
Page 5of 10
Removing the motor
1. Unscrew the four screws (1).
2. Remove the motor (2).
Tools:
- Socket head wrench,
5 mm
1
2