Fender HAMMERTONE REVERB User manual

NOTES: UNLESS OTHERWISE SPECIFIED.
1. SINGLE-COLOR PLUS GRAYSCALE
2. USE 24 LB. BOND MATTE PAPER
3. NO-BLEED PRINTING REQUIRED
4. PAGE SIZE: 2.6 INCHES WIDE X 4.25 INCHES HIGH
5. FOLDED AND SADDLE STAPLED
6. SAMPLES OF FIRST PARTS MUST BE APPROVED BY FENDER
R&D BEFORE STARTING PRODUCTION. QTY 3 UNLESS
OTHERWISE SPECIFIED.
DO NOT PRINT
THIS PAGE
REVISIONS
REV. DESCRIPTION BY DATE
A
PART NUMBER SIZE
PRODUCT MANAGER
TITLE
REV
DATE
PROJECT ENGINEER
FENDER MUSICAL INSTRUMENTS CORP.
RESEARCH & DEVELOPMENT
CORONA, CALIFORNIA U.S.A.
THIS DOCUMENT CONTAINS INFORMATION OF PROPRIETARY NATURE TO FENDER
MUSICAL INSTRUMENTS AND IS SUBMITTED TO YOU IN CONFIDENCE AND SHALL NOT
BE DISCLOSED OR TRANSMITTED TO OTHERS WITHOUT AUTHORIZATION FROM
FENDER MUSICAL INSTRUMENTS
ANY PART SUPPLIED FOR USE
IN ANY FENDER PRODUCT
MUST CONFORM TO THE
EUROPEAN RoHS DIRECTIVE.
COPYRIGHT - 2/18/2022 -
FENDER MUSICAL
INSTRUMENTS CORP.
TITLEBLOCK REVISION: 2.1
DATE
PROJECT MANAGER DATE
B
J.O.
2.18.22
damp control description revised
MANUAL OWNER'S, HAMMERTONE
REVERB EFFECT PEDAL
B
7724435000
02/22/2022

INPUT JACKOUTPUT JACK
DC POWER CONNECTOR
FOOTSWITCH
LED

Thanks for purchasing the Hammertone Reverb—
a classic effect that adds richly resonant depth,
dimension and atmosphere to your sound.
Enter a world of ringing reverb possibilities with
time, damp, and level controls, and use the Type
and Tone switches to tailor the tonal character
even more, including hall, room and plate reverb
modes. Reverb is a time-honored essential in the
arsenal of any guitarist, and the Hammertone
Reverb puts this sonorous sound at your feet in
every shade from delicate to drenched.
HAMMERTONE REVERB

OUTPUT JACK
Low-impedance output connects to amp or next pedal in signal chain.
INPUT JACK
High-impedance input for electric guitar, bass, acoustic guitars with
pickup systems, keyboards and other instruments.
DC POWER CONNECTOR
Connect DC adapter here. Standard center-negative 9VDC jack for use
with appropriate power supplies.
TIME CONTROL KNOB
Adjusts reverb decay time.
DAMP CONTROL KNOB
Adjusts the amount of high-end “shimmer” in the reverb effect. Higher
settings damp the effect more for a darker reverb sound; lower settings
let top end ring out for a brighter sound.
LEVEL CONTROL KNOB
Adjusts volume of reverb signal.
TYPE SWITCH
Three-position switch for Hall (up), Room (middle) and Plate (down)
reverb types.
TONE SWITCH
For normal (up) and dark mode (down). Dark mode rolls off treble,
letting reverb sit more easily in some mixes.
LED
Illuminates when effect is on.
FOOTSWITCH
Turns effect on and off.

A PRODUCT OF
FENDER MUSICAL INSTRUMENTS CORPORATION
CORONA, CALIFORNIA, U.S.A.
Fender®is a registered trademark of FMIC.
Copyright © 2022 FMIC. All rights reserved.
PN 7724435000 REV B
IMPORTANT SAFETY INSTRUCTIONS
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC
power to rain or moisture.
•Do not alter the AC plug of the connected power adapter
•Do not drip or splash liquids on the unit.
•No user serviceable parts inside, refer servicing to qualified personnel only.
•WARNING: The unit must only be connected to a safety agency certified, regulated,
power source (adapter), approved for use and compliant with applicable local and
national regulatory safety requirements.
•Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth
for cleaning and then wait until the unit is completely dry before reconnecting it to power.
•Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable
of producing very high sound pressure levels which may cause temporary or permanent
hearing damage. Use care when setting and adjusting volume levels during use.
ADDITIONAL LANGUAGES
Manual available in additional languages at
www.fender.com/support
Product specifications subject to change without notice
SPECIFICATIONS
IMPEDANCES
POWER SUPPLY
POWER REQUIREMENTS
DIMENSIONS
WEIGHT
Input: 500kΩ Output: 470Ω
9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
100mA @ 9VDC
2.44” x 4.4” x 2.2” (62mm x 111.8mm x 55.9mm)
0.50 lbs (0.23kg)
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

© FENDER MUSICAL INSTRUMENTS 2021