Fender THE TRAPPER User manual

THE TRAPPER

14
15
1
3
11
9
6
1. Bypass Footswitch
2. Jewel Indicator
3. Output Jack
4. Contour
5. Tone
6. Level 1
7. Level 1 LED
8. Level 2
9. Fuzz 2
10. Octave Switch
11. Input Jack
12. Select Footswitch
13. Low Battery Indicator
14. LED Kill Switch
15. DC Power Connector
4
12
LEDs
9V DC
INPUT
THE TRAPPER
OCTAVE
CONTOUR
LEVEL 1
FUZZ 2
13
2
10
SELECTBYPASS
7 85
LEVEL 2TONE

Thanks for purchasing The Trapper – a radical
new dual fuzz pedal. The Trapper features two
distinctly different voices that can be toggled
used the Select Footswitch. The first voice features
dedicated Fuzz and Level controls, as well as a
high-octave toggle switch. The second fuzz relies
mainly on the guitar’s volume and tone controls
for modification, with Level as the only parameter.
This circuit also employs a noise gate for some
truly distinctive “glitchy” sounds.
THE TRAPPER
DESIGNED IN CALIFORNIA, U.S.A.

Contour
Controls frequency range emphasis. Turn knob counterclockwise
for bass boost/treble cut; turn clockwise for opposite. At middle
position, mid frequencies are de-emphasized.
Tone
Controls amount of high-frequency signal content. Turn
counterclockwise for darker sound; turn clockwise to brighten
sound.
Level 1
Controls output level of rst fuzz circuit.
Level 1 LED
Illuminates when rst fuzz circuit is selected.
Level 2
Controls output level of second fuzz circuit.
Fuzz 2
Controls amount of fuzz in second circuit; turn clockwise for
greater saturation.
Octave Switch
Adds a high octave to signal.
Jewel Indicator
Illuminates when eect is engaged.
Bypass Footswitch
Bypasses eect.
Select Footswitch
Toggles between both fuzz circuits.

Input Jack
High-impedance input suitable for electric guitar, bass, acoustic
guitars with pickup systems, keyboards and other instruments.
Output Jack
Low-impedance output jack connects to amp or to next eect
pedal in signal chain.
DC Power Connector
Standard center-negative 9VDC jack for use with appropriate
power supplies.
LED Kill Switch
Deactivates control-knob illumination.

A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORPORATION
CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC.
Copyright © 2019 FMIC. All rights reserved.
P/N 7717102000 - REV 1
Important Safety Instructions
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC
power to rain or moisture.
•Do not alter the AC plug of the connected power adapter
•Do not drip or splash liquids on the unit.
•No user serviceable parts inside, refer servicing to qualified personnel only.
• WARNING: The unit must only be connected to a safety agency certified, regulated,
power source (adapter), approved for use and compliant with applicable local and
national regulatory safety requirements.
• Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth
for cleaning and then wait until the unit is completely dry before reconnecting it to power.
• Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable
of producing very high sound pressure levels which may cause temporary or permanent
hearing damage. Use care when setting and adjusting volume levels during use.
Additional Languages
Manual available in additional languages at:
www.fender.com/support
Product specifications subject to change without notice
Specifications
IMPEDANCES:
POWER SUPPLY:
POWER REQUIREMENTS:
DIMENSIONS:
WEIGHT:
INPUT: 820kΩ OUTPUT: 470Ω
9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
80mA @ 9VDC
3.75” x 4.9” x 2.5” (95.25mm x 124.5mm x 63.5mm)
1.2lbs (.54kg)

NOTES:

© FENDER MUSICAL INSTRUMENTS 2019