© Ferno Australia / 00425-V1 / Aug 2018 7
3 INSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE
3.1 General Safety Instructions
1. The IndustriPOD® and associated hardware must always
be secured to prevent it from tipping and falling over. The
IndustriPOD® may become unstable if used without an
assessment of the resultant force and direction. Additional
rigging may be required to ensure complete stabilisation.
2. Ensure the Operator is in good physical and mental health and
is trained and competent in the use of the device. The Operator
must employ all relevant PPE for the job prior to commencement
of working at height. PPE may include, but is not limited to a
harness, lanyard, helmet, gloves and appropriate foot wear.
3. Ensure you have a rescue plan in place prior to working at height
or conned space. A rescue plan is mandatory and the Operator
must be aware of it prior to commencing work.
4. Do not alter, modify or tamper with the IndustriPOD® in any way
or form. The IndustriPOD® may not be rectied or serviced by
any person unless they are appropriately trained and authorised
by Ferno Australia.
5. When the IndustriPOD® is used as part of a fall arrest system, the
User must be equipped with a means of limiting the maximum
dynamic forces exerted on the user during the arrest of a fall to
a maximum of 6kN.
6. A lanyard assembly should be secured to an anchorage point
which is at a level that will result in the minimum free fall and
the least total fall distance consistent with the wearer’s ability to
carry out work tasks.
7. When making a connection to any point on a harness which
cannot be seen by the wearer of the harness, it should either be
made before putting the harness on, or the connection should
be connected or checked for security by a second person.
8. Always ensure anchor points are positioned so as to avoid a
pendulum eect during a fall which may cause body contact
with structures or machinery below. The maximum angle from
the anchor point must not exceed 15° either side of the centre of
the anchor point (Figure 10).
9. If any part of an assembly is to be exposed to chemicals (eg.
caustic materials or hazardous atmospheres), the user should
consult Ferno Australia to determine whether the part is suitable
for continued use.
WARNING
Do not use the IndustriPOD® beyond its specied limitations,
or for any purpose other than that for which it is intended.
Ensure the compatibility of equipment used within the system.
Dangers may arise when the safe function of any one item of
equipment is aected by or interferes with the safe function
of another.
Do not use your IndustriPOD® if any parts are missing.
3.2 Before Each Use
Operator Inspection
The product should be inspected by a competent person before and
after each use to ensure it functions correctly and all components
are damage free. A checklist is provided below as a guide that may
be used in conjunction with your approved workplace protocols.
Refer also to Inspecting the IndustriPOD® on page 14.
Inspect the IndustriPOD® for:
1. Do the legs t together and extend smoothly?
2. Are the legs bent, cracked or deformed?
3. Are all fasteners (e.g. bolts, pins) present and securely
tightened?
4. Is retaining hardware on pins present and in good condition?
5. Are the pins in good condition and functioning correctly?
6. Are the pulleys in good condition and functioning correctly?
7. Do any plastic parts show signs of wear or chemical damage?
8. Are the feet and lashing holes showing signs of deformation,
damage and sharp edges?
9. Is the adjustable foot tether present and in good condition?
Refer any signs of deterioration to a competent person for a decision
on the safety and serviceability of the product. If in doubt, tag it out!
NOTICE
Operating in, or exposing the IndustriPOD® to extreme
temperatures, caustic chemicals, hazardous environments
or excessively rough handling / treatment may cause
damage.
