Ferroli DOMIcompact F 30 D Troubleshooting guide

wall-mounted gas fired,
combination boiler
DOMIcompact F 30 D
INSTRUCTIONS FOR USE, INSTALLATION AND MAINTENANCE
FOR THE UNITED KINGDOM &EIRE
cod. 3540B62/3 - 05/2006

GC N° 47-267-40

2
DOMIcompact F 30 D
IMPORTANT
Your "benchmark" Installation, Commissioning and Service Record Log Book is enclosed in the
last pages of this manual. “This record must be completed and left with the end user”.
Ferroli is a member of the Benchmark initiative and fully supports the aims of the programme.
Benchmark has been introduced to improve the standards of installation and commissioning of central
heating systems in the UK and to encourage the regular servicing of all central heating systems to
ensure safety and efficiency.
Please see installation and servicing guidelines.
For EIRE (Southern Ireland) it is necessary to complete a “Declaration of Conformity” to indicate
compliance to I.S. 813. An example of this is given in the current edition of I.S. 813. In addition it is
necessary to complete the “Benchmark” logbook.
• Read the warnings given in this manual thoroughly.
They provide important information for safe instal-
lation, use and maintenance
• The instruction manual, by law must be left with the
end user.
• If the appliance is sold or transferred to another
owner or if the owner moves, leaving the appliance
behind, always ensure that the manual is kept with
the appliance for consultation by the new owner
and /or installer.
• Incorrect installation or poor maintenance absolves
the manufacturer from all liability for damage to
persons and property.
• Installation and maintenance must be carried out
in accordance with current legislation, according
to the manufacturer’s instructions and by qualified
corgi registered engineer.
• Before service or maintenance work is carried out
isolate the appliance from the mains electricity
supply.
• In the event of malfunction or faulty operation, iso-
late the appliance. Do not attempt to repair or carry
out any other operation on the appliance directly.
Contact Ferroli or a qualified engineer only.
• Repairs or the replacement of components must be
carried out exclusively by qualified personnel using
original spare partsonly. Failure toadhere to theabove
may compromise the safety of the appliance.
• To guarantee efficient operation, the appliance must
be serviced once a year by a Corgi registered engi-
neer.
• The appliance may not be used for purposes other
than those for which it was explicitly designed.
• Incorrect installation and use or failure to follow the
instructions provided by the manufacturer absolve
the manufacturer from all liability for damage.
• After unpacking, check that the contents are correct
and undamaged.
• Keep packing out of reach of children as it could be
potentially hazardous.
• To clean external parts, use a damp cloth moistened
with soapy water if necessary. Avoid using abrasive
cleaning products and solvents.
This symbol indicates “Caution” and is placed next to all safety information.
Strictly follow these instructions in order to avoid danger and damage to persons
or property.
This symbol calls attention to a note or important information, please read thou-
roughly.
President and Legal Representative
Cav. del Lavoro
Dante Ferroli




Declaration of conformity
Manufacturer: FERR LI S.p.A.
Address: Via Ritonda 78/a 37047 San Bonifacio VR Italy
declares that this unit complies with the following EU directives:
Gas Appliance Directive 90/396
Efficiency Directive 92/42
Low Voltage Directive 73/23 (amended by 93/68)
Electromagnetic Compatibility Directive 89/336 (amended by 93/68)

3
DOMIcompact F 30 D
1. Operating instructions............................................................................4
1.1 Introduction ............................................................................................................4
1.2 Control panel ..........................................................................................................5
1.3 Turning on and off ..................................................................................................6
1.4 Adjustments ............................................................................................................6
1.5 Maintenance............................................................................................................8
1.6 Faults.......................................................................................................................8
2. Installation ..............................................................................................9
2.1 General Instructions................................................................................................9
2.2 Boiler location .......................................................................................................10
2.3 Boiler water connections ......................................................................................12
2.4 Connection to the gas system..............................................................................14
2.5 Electrical Connections ..........................................................................................14
2.6 Flue System...........................................................................................................17
3. Service and maintenance......................................................................24
3.1 Adjustments ..........................................................................................................24
3.2 Initial start-up........................................................................................................26
3.3 Maintenance..........................................................................................................27
3.4 Troubleshooting....................................................................................................29
4 Technical characteristics and data .........................................................30
4.1 Dimensions and connections ................................................................................30
4.2 General view and main components ....................................................................31
4.3 Hydraulic diagram.................................................................................................32
4.4 Technical data table..............................................................................................33
4.5 Diagrams ...............................................................................................................34
4.6 Time Clock (optional) ............................................................................................35
4.7 Wiring diagram .....................................................................................................36
Benchmark................................................................................................37
cod. 3540B62/3


4
DOMIcompact F 30 D
1. OPERATING INSTRUCTIONS
1.1 Introduction
Dear Customer,
Thank you for choosing DOMIcompact F 30 D, a FERROLI wall-mounting boiler featuring advanced
design and technology, high reliability and quality construction. Please read this manual carefully and
keep it for future reference.
DOMIcompact F 30 D is a high-efficiency non condensing appliance for heating and hot water production
running on natural or liquefied petroleum gas (configurable at the time of installation) and regulated by
an advanced microprocessor control system.
The boiler shell consists of a primary copper laminar heat exchanger and burner equipped with electronic
ignition and ionization flame control.
The boiler is totally room sealed from the installation room: the air required for combustion is drawn
from outside. The boiler also includes a fan, modulating gas valve, pump, expansion vessel, flow switch,
safety valve, temperature sensors, a safety thermostat and a low water pressure switch.
Thanks to the microprocessor control and adjustment system with advanced self-diagnosis, unit ope-
ration is for the most part automatic. The power for heating is automatically governed by the control
system combined with the room thermostat (not supplied). The power for hot water is automatically and
continually governed to ensure a fast delivery and comfort under all operating conditions.
The user only has to set the temperature desired inside the home (by means of an optional room
thermostat or remote control, which is required under the building regulations 2002) or regulate the
temperature of the system, and set the desired outlet temperature for the hot water. The adjustment
and control system will provide optimum operation throughout the year.
The display continuously provides information on the unit’s operating status and it is possible to obtain
additional information on the sensor temperatures, set-points, etc, or configure them. Any operating
problems associated with the boiler are immediately signalled by the display and, if possible, corrected
automatically.

5
DOMIcompact F 30 D
1.2 Control panel
The control panel is composed of a multi-function button, two knobs and a display.
Key
1 Heating temperature adjustment and
Summer/Winter/ switch off control
2 Hotwater temperature adjustment and switch
off control
3 Multi-function button (ECO/RESET/TEST)
4 Temperature display
During operation or standby in heating mode,
it displays the temperature of the heating
sensor. Duringhot water operation, itdisplays
the temperature of the hot water sensor.
5 Heating demand symbol
Appears during heating operation or when
adjusting the heating set-point tempera-
ture
6 Flame symbol
Appears when the burner is on
7 ECO symbol
ECO is displayed when the Economy function
is on
8 Hot water demand symbol
Appears during hot water operation or when adjusting the hot water set-point temperature
Fig. 1
Boiler on stand-by
Boiler on stand-by / EC
Heating operation
(burner on)
Hot tap water operation
(burner on)
Fault codes (See chap. 1.6 or 3.0)
TEST mode operation
(burner on)
Boiler off
Display Type of operation
(Frost protection active)
(No demand from heating or Hot water)
(Displays heating flow temperature)
(Displays Hot water temperature)
(Displays relevant fault code)
(For comissioning purposes only)
Information during operation
During normal operation, the boiler diagnostics display the running information or boiler status on the
control panel (Fig.1).see below.

6
DOMIcompact F 30 D
1.4 Adjustments
Boiler off Boiler in Summer operation
(only hot water production is active)
Boiler with only heating on and hot
water off (Display indicates heating demand)
Boiler in Winter operation
(Display indicates hot water demand)
1.3 Turning on and off
Ignition
• Open the gas isolation valve on the boiler.
• Purge the air from the pipe work to the gas valve.
• Turn on the 3amp electrical switch or insert the plug to the
boiler.
• Turn the heating and hot water control knobs onto their required
temperatures (see par. 1.4).
• The boiler is now ready to function automatically whenever hot
water is drawn or both the time clock and room thermostat call
for heating.
Turning off
Turn the knobs (ref. 1 and 2 Fig. 1) onto minimum.
If the boiler is turned off this way, then the P.C.B is still powe-
red.
Hot water and heating operation are disabled, the display shows
; but the frost protection function remains active
The frost protection will not work if the electricity and/or gas supply to the unit are cut off.
To avoid damage caused by freezing during long shutdowns in winter, it is advisable to drain all
water from the boiler, the tap water and the system water; or drain off just the tap water and
add a suitable antifreeze to the heating system, as prescribed in chap. 2.3.
Summer/winter Switchover
Depending on the position of the control knobs “1” and “2” it is possible to switch off the boiler unit,
switch between summer and winter operation or turn off the domestic hot water .

7
DOMIcompact F 30 D
Switching off the boiler. Switching between summer and winter operation has priority over the
heating only time control (optional) when this is connected to the boiler.
C.H. temperature setting
To set the system delivery temperature, turn the knob (ref. 1 - Fig. 1).
It can vary from a minimum of 30 °C to a maximum of 85°C; however, it is advisable not to operate the
boiler below 45 °C. When the knob is turned the display lights up, the radiator symbol flashes and the
temperature displayed will be the temperature actually set. On completing this operation, the display
will stay on for another 5 seconds and then go back to the actual operating temperature providing
there is a demand.
Domestic Hot water temperature adjustment
To set the tap water temperature, turn the knob (ref. 2 - Fig. 1).
It can vary from a minimum of 40 °C to a maximum of 55 °C. When the knob is turned the display lights
up, the tap symbol flashes and the temperature displayed will be the temperature actually set. On
completing this operation, the display will stay on for another 5 seconds to then go back to the actual
operating temperature providing there is a demand.
If the boiler is connected to the optional remote open therm control, the above adjustments
(system and hot water temperature) can only be made with the remote control.
ECO/COMFORT selection
The unit is equipped with a special internal device that ensures a high hot-water delivery speed and
excellent user comfort. When comfort mode is active the water in the boiler is maintained at a pre-
determined temperature, which means that hot water is available at the boiler outlet as soon as a tap
is opened, ie with no waiting.
The user can turn the device off (ECO mode) by pressing the multi-function button for 2 seconds with
the boiler on standby. In ECO mode the display shows the relevant symbol. To turn on COMFORT mode,
press the multi-function button again for 2 seconds, the ECO symbol will vanish from the display.
TEST MODE selection
Pressing the multi-function button 3 times in 3 seconds turns on TEST mode (the heating and hot
water symbols flash simultaneously - see par. 3.1). If TEST mode is turned on by accident, press
the button 3 times in 3 seconds again to exit (Test time 15 minutes unless cancelled early).

8
DOMIcompact F 30 D
1.5 Maintenance
It is strongly recommended to carry out annual maintenance on the boiler and the heating system. Please
refer to the “maintenance” section in this manual.
The casing, the control panel and the aesthetic parts of the boiler can be cleaned using a soft and damp
cloth.
Do not use abrasives or solvents.
1.6 Faults
The boiler is equipped with an advanced self-diagnosis system that signals any faults on the display.
Some faults (from F1 to F3) cause a boiler shutdown. In this case, operation must be reset manually by
pressing the multi-function button (RESET) for 1 second
Other faults (from F5 to F37) cause temporary shutdowns that are automatically reset as soon as the
value causing the fault comes back within the boiler’s normal working range.
Listed below are some anomalies that can be caused by simple, user-solvable problems.
If the problem remains after two attempts at resetting, contact the Ferroli Service Centre.
For other faults, refer to section 3.4 “Troubleshooting”.
Before calling a Ferroli service engineer, check that the problem is not due to there being no
gas or electricity, or low system pressure.
Boiler shutdown
Low system pressure
Make sure that the gas cocks ahead of the boiler and on the
meter are open.
Press the multi-function button (for 1 second) (fig.1)
In case of repeated shutdowns, contact the nearest assistance
centre.
Fill the system to 1-1.5 bar using the external filling loop
normally fitted under the boiler by your installer.
Fault CureDisplay code

9
DOMIcompact F 30 D
2. INSTALLATION
2.1 General Instructions
This device must only be used for the purpose for which it is specially designed. This unit is
designed to heat water to a temperature below boiling point and must be connected to a hea-
ting system and/or a water supply system for domestic use, compatible with its performance,
characteristics and its heating capacity. Any other use is considered improper.
BOILER INSTALLATION MUST ONLY BE PERFORMED BY QUALIFIED PERSONNEL, IN ACCORDANCE
WITH ALL THE INSTRUCTIONS GIVEN IN THIS TECHNICAL MANUAL, THE PROVISIONS OF CURRENT
LAW, THE RECOMENDATION OF BS STANDARDS, ANY LOCAL REGULATIONS AND THE RULES OF
COMPETENT WORKMANSHIP.
In IE, the installation must be carried out by a Competent Person and installed in accordance with the
current edition of I.S. 813 “Domestic Gas Installations”, the current Building Regulations and reference
should be made to the current ETCI rules for electrical installation.
Incorrect installation can cause damage or physical injury for which the manufacturer declines any
responsibility.
This appliance must be installed strictly in accordance with these instructions and
regulations:
The Gas Safety Regulations (Installations & Use).
The Local Building Regulations.
The Building Regulations (Part L).
The Buildings Standards (Scotland - Consolidated) Regulations.
British Standards Codes of Practice:
B.S. 5440 Part 1 Flues
B.S. 5440 Part 2 Air supply
B.S. 5449 FORCED CIRCULATION HOT WATER SYSTEMS
B.S. 6798 INSTALLATION OF GAS FIRED HOT WATER BOILERS
B.S. 6891 GAS INSTALLATIONS
B.S. 7671 IEE WIRING REGULATIONS
B.S. 4814 SPECIFICATION FOR EXPANSION VESSELS
B.S. 5482 INSTALLATION OF LPG
B.S. 3632 RESIDENTIAL PARK HOMES
B.S. 7593 TREATMENT OF WATER IN DOMESTIC HOT WATER CENTRAL HEATING SYSTEMS
B.S. 5546 INSTALLATION OF HOT WATER SUPPLIES FOR DOMESTIC PURPOSES
I.S. 813 DOMESTIC GAS INSTALLATIONS (EIRE ONLY)
Local Water Bye Laws
B.S. 5955-8 PLASTIC PIPEWORK INSTALLATION
For Northern Ireland the rules in force apply

10
DOMIcompact F 30 D
Minimum
A
B
D
5 cm
20 cm
60 cm
(via an openable panel)
C20 cm
Table 1
fig. 2
2.2 Boiler location
The boilers combustion chamber is sealed off from the installation room. The installation room must be
sufficiently well ventilated to prevent any dangerous conditions from forming in the event of even slight
gas leakage. This safety standard is required by the EEC Directive no. 90/396 for all gas units, including
those with a so-called sealed chamber.
Therefore the place of installation must be free of dust, flammable materials or objects or corrosive
gases. The room must be dry and not subject to freezing.
The boiler is design to be installed on a solid wall. The wall fixing must ensure a stable and effective
support for the appliance, using the bracket and fixings supplied.
If the unit is enclosed in a cupboard or mounted alongside, there must be space for normal maintenance
work. Fig. 2 and tab. 1 give the minimum clearances to leave around the unit.
This appliance does not require compartment ventilation for combustion purposes
Drilling Template
Select suitable mounting position for boiler, using the template mark flue outlet and boiler mounting
points. Drill two 10mm holes 70mm deep to accept the wall plugs. Fit the supplied wall plugs on the
left and right side drill and fit the special wall plug in the middle (fig. 3). Fix the wall bracket to the wall
using standard lock nuts (M8) on both sides. Using a Core drill cut a hole 10-20 mm larger than the flue
diameter for the flue as detailed on page 17.
fig. 3
D
A A
B
C

11
DOMIcompact F 30 D
fig. 4
Gas
Hot water
Additional expansion
vessel C.H. (if required)
Filling
point C.H.
Automatic
Bypass
fig. 5
3
2
1
4
Cold water inlet
Make Up Water
Provision must be made for replacing water lost from the sealed system. Reference should be made
to BS6798, for methods of filling and making up sealed systems. There must be no direct connection
between the boiler's central heating system and the mains water supply. The use of mains water to
charge and pressurise the system directly, is conditional upon the Local Water Byelaws. Again any such
connection must be disconnected after use. The temporary filling loop (Not supplied) is shown in fig. 5.
Ensure the filling point is on the return pipe to the boiler.
Attention - is drawn to the Local Water Byelaws.
Fittings manufactured from duplex (alpha-beta) brass are not acceptable for underground use and certain
water undertakings will not accept their use above ground.
Ensure all pipework is adequately supported
NOTE: An automatic bypass capable of
passing 6 ltrs per minute must be fitted as
far as possible from the boiler if thermosta-
tic radiator valves are fitted thoughout.
As per the building regulations part ‘L’
Key
1 Filling point C.H 15mm
isolation valve.
2 Temporary flexible connection
3 Cold water supply 15mm
isolation valve
4 Double check valve

12
DOMIcompact F 30 D
It is essential to install the isolation valves supplied between the boiler and heating system, allowing the
boiler to be isolated from the system if necessary.
The safety valve outlet must be connected to a 15 mm pipe to allow safe discharge to the outside
ground in the event of over-pressure in the heating circuit. If this is not done, and the drain valve
opens and floods the room, the boiler manufacturer is not to be held responsible. The pipework
must have a continuous fall from the boiler, The outlet should face back against the outer bri-
ckwork or building face to prevent harm or injury from hot water discharging in the event of an
over-pressuried system.
Make the boiler connection in such a way that its internal pipework is free of stress.
If a check valve is installed on the tap water circuit (where applicable), it is necessary to mount a safety
valve between the boiler and this circuit (check valve minimum 3 metres from boiler).
fig. 6
2.3 Boiler water connections
The heating capacity of the unit should be previously established by calculating the building’s heat
requirement according to current regulations. For efficient operation and long life of the boiler, the
plumbing system must be well designed and always complete with all those accessories that guarantee
regular operation and running, ie room thermostat, trv’s and automatic bypass etc.
If the flow and return pipes follow a path where air pockets could form in certain places, it is essential
to install air vent valves at these points. Also, install a type “A” drain cocks at the lowest points in the
system to allow its complete draining.when required The temperature differential between the flow
manifold and the return to the boiler should not exceed 20° C.
A minimum flow of 6 litres/min is requied through the heat exchanger, it is therefore essential to fit an
automatic bypass a min of 3 metres away from the appliance, This should be calibrated on site.
Do not use the water system pipes to earth
electrical appliances.
Before installation, carefully flush all the pipes of the
heating system to remove residues or impurities that
could affect the unit’s efficient operation (BS 7593
Building regs Doc L).
Make the connections to the appliance as shown in
fig. 6.
Key
1 Heating system flow Ø 3/4”
2 Hot water outlet Ø 1/2”
3 Gas inlet 1/2”
4 Tap water inlet Ø 1/2”
5 Heating system return Ø 3/4”
36 95 60 120 95 54
460
196
1 2 3 4 5
247

13
DOMIcompact F 30 D
The connecting kits shown in fig. 7 are supplied as standard.
ey
A = Nut
B = Compression olive
D = 3/4 seal (green)
E = 1/2 seal (green)
F = 1/2 gas seal (blue)
Flow isolation valve
Hot water connection
Gas isolation valve
Cold water isolation valve
Return isolation valve
Ø22
Ø22
Ø22
Ø15
Ø15
A
A
A
A
AB
B
B
B
B
D
D
E
E
F
fig. 7
Water treatment
When treatment is used ferroli limited only recommend the use of proprietary Brands, such as Fernox or
Sentinel water treatment products, which must be used in accordance with the manufacturers instruc-
tions,
For further information contact:
Fernox Manufacturing Co. LTD.
Cookson Electronics, Forsyth Road
Sheerwater,Woking,Surrey GU21 5RZ
Tel: [phone]
Sentinel Performance Solutions
The Heath Business & Technical Park
Runcorn
Cheshire
WA7 4QX
Tel: [phone]
Note - When the boiler is installed with an existing or new system any unsuitable additives or system
debris must be removed by thorough chemical cleansing. All systems should be cleansed according to
B.S. 7593.
Note - It is important that the correct concentration of the water treatment product is maintained in
accordance with the manufacturers instructions.
Note - In hard water areas it may be necessary to install a scale reducer prior to the boiler on the cold
water inlet.

14
DOMIcompact F 30 D
2.4 Connection to the gas system
If necessary the local Gas supplier should be consulted, at the installation planning stage, in order to
establish the availability of an adequate supply of gas.
An existing service pipe must not be used whitout prior consultation with the local Gas supplier.
A gas meter can only be connected by the Local Gas supplier, or by a Local Gas suppliers Contractor.
Installation pipes should be fitted in accordance with BS6891.
Appliance inlet working pressure must be 20 mbar MINIMUM, for NG and 37 mbar minimum for pro-
pane.
Do not use pipes of a smaller diameter than the combination boiler inlet gas isolation valve (22 mm).
The complete installation must be tested for gas soundness and purged as described in BS6891.
All pipework must be adquately supported. An isolating gas valve is provided and must be fitted
on the boiler gas inlet. Please wait 10 minutes when lighting from cold before checking the gas
rate, this will ensure thermal equilibrium.
2.5 Electrical Connections
The unit must be installed in conformity with current national and local regulations inc 16th Edition &
B.S 7671.
Connection to the electrical supply.
The boiler must be connected to a single-phase, 230 Volt-50 Hz electrical supply.
The unit’s electrical safety is only guaranteed when correctly connected to an efficient earthing
system installed according to current safety standards and checked by a professionally qualified
person. The manufacturer is not responsible for any damage caused by failure to earth the system.
Also make sure that the electrical system is adequate for the maximum power absorbed by the
unit, as specified on the boiler dataplate, in particular ensuring that the cross-sectional area of
the electrical cables are suitable for the power absorbed by the unit.
The boiler is prewired and provided with a cable for connection to the electrical supply The prewired
cable must be connected to the supply with a permanent connection and equipped with a double pole
switch which contacts have a minimum opening of at least 3 mm, and fused at max. 3A between the
boiler and the line. It is important to check the polarities (LIVE: brown wire / NEUTRAL: blue wire /
EARTH: yellow-green wire) and ensure they are correctly connected to the corresponding terminals on
the electrical supply.
The user must never change the boilers power cable. If the cable gets damaged, switch off the unit
and have it changed only by professionally qualified personnel. If changing the electric power ca-
ble, use only “HAR H05 VV-F” 3x0.75 mm2cable with a maximum outside diameter of 8 mm.
5 Core cable must not be used to replace the existing 3 core!

15
DOMIcompact F 30 D
Integral clock installation
1Unscrew the two screws “A” (Fig. 8a).
2Lower the instrument panel (Fig. 8b).
3Turn the instrument panel (Fig. 8c).
4Open the instrument panel “B” (Fig. 8c), mount
the clock into the facia panel using the two screws
provided.
5Take the cable with blue and brown wires and the
"JST" connector: connect the loose spades to clock
terminal 1 & 2 (Fig. 8e).
6Connect the plug end of the cable to terminal X5 of
the MF08FA.1 board.
7Remove one cable from the terminal block (Fig.
8d).
8Connect it to the cable “C” of the Fig. 8e.
9Connect the cable “D” in the free space of terminal
block (Fig. 8d).
10 Replace everything in reverse order.
1 2 3 4 5 6 7 8 9 10 11
X2
72
fig. 8d
C
D
Clock
1 235
JST
Molex
NOT USED!!!
fig. 8e
Fig. 8b
B
fig. 8c
AA
fig. 8a

16
DOMIcompact F 30 D
Fig. 9b
B
fig. 9c
AA
Access to the electrical terminal block
To access the terminal block where the room thermostat (Low voltage) or the remote timer control is to
be connected, carry out the following operations:
1Unscrew the two screws “A” (Fig. 9a).
2Lower the instrument panel (Fig. 9b).
3Turn the instrument panel (Fig. 9c).
You can now access the terminal block “B” (Fig. 9c)
fig. 9a
1
2
Room
thermostat
1
2
Remote
timer
control
(Opentherm)
Or
Voltage free
contacts

17
DOMIcompact F 30 D
Choosing the restrictors using
a concentric system
Choosing the restrictor using
two pipe system
2.6 Flue System
The unit is “type C” with an airtight chamber and forced draught, the air inlet and flue outlet must be
connected to one of the following flue system. With the aid of the tables and methods of calculation
indicated, before commencing installation, it is first necessary to check that the flue ducts do not exceed
the maximum permissible lengths. The current standards and local regulations must be observed.
This C-type unit must be installed using the flue components supplied by FERROLI S.p.A. in
accordance with UNI-CIG 7129/92. Failure to use them automatically forfeits all warranty and
liability of FERROLI S.p.A.
Restrictors
Boiler operation requires fitting the restrictors supplied with the unit as instructed in the following
tables.
The restrictor Ø45 is fitted as standard on all boilers.
Before inserting the flue outlet pipe, it is therefore necessary to check there is the right restrictor
(when it is to be used) and that it is correctly positioned.
Type
Concentric
60/100
Length up to:
1 end + 1 metre
1 end + 3 metres
1 end + 3 metres
1 end + 5 metres
Restrictor to use
45 mm
No restrictor
45 mm
No restrictor
Concentric
80/125
45 mm
47 mm
50 mm
No restrictor
Min
0 m
15 m
35 m
45 m
Max
15 m
35 m
45 m
50 m
Pipe length calculated
in linear metres Restrictor to use
1
2
4
33
1
2
Restrictor
Restrictor
5
6

18
DOMIcompact F 30 D
Connection with concentric flue
The unit can be connected to a concentric flue with a horizontal or vertical flue as shown on the following
drawings. Numerous accessories are available on request to meet the various installation requirements.
Please refer to the flue accessory catalogue or the price list.
Rear Outlet
Side view
View from above
Fig. 10a
Side Outlet
Fig. 10b
Front view
View from above
P = S + 191,5 mm
L = S + D + 215 mm
Drill the wall 10 - 20 mm
more than the pipe
diameter
* = between
10 e 60 mm.
Codo 60/100
010007X0 Codo 60/100
010007X0
P
125
S
70
70
S50* 125
P
70
DS50* 125
30
L
95
DS
L
125
70
208
208
141,5
30
43
Cut the internal pipe
70 mm longer than P
Cut the internal pipe
70 mm longer than L
* = between
10 e 60 mm.
Drill the wall 10 - 20 mm
more than the pipe
diameter
Tilt flue downwards
from the boiler by
3 mm/m
Tilt flue
downwards from
the boiler by
3 mm/m
70 min.
Ø60 Ø100
70 min.
50*
95
80
30 50*
30
95
80
80 -3 mm/m
230 230
230 230
230 230

19
DOMIcompact F 30 D
Vertical Outlet
For the installation:
1.Define the position for installing the unit.
2.Drill the wallfor the air/flue pipeoutlet according
to the references stated in the figures, consi-
dering that the horizontal sections of piping
must have a gradient of approximately 3 mm
per metre of length downwards to prevent any
rainwater getting into the boiler.
3.Make a hole of diameter 10 - 20 mm greater
than the nominal diameter of the flue pipe used
to facilitate insertion.
4.If necessary, cutthe end pipe tosize, considering
that the external pipe must protrude from the
wall by between 10 and 60 mm (Fig. 10a and
10b). Eliminate the cutting burrs.
5.Connect the ducts to the boiler, positioning
the gaskets correctly and seal the wall coupling
points with special sleeves.
Fig. 10c
The total length in linear metres of the flue
pipe must not exceed the maximum lengths
stated in the following table, considering that
each bend gives rise to the stated reduction.
For example, a duct D= 60/100 composed of 1
bend of 90° +1 horizontal metre + 2 bends of
45° + 1 horizontal metre has a total equivalent
length of 4 metres.
Reduction factors for bends
Concentric end at 90° - Ø 60/100 mm
Concentric end at 45° - Ø 60/100 mm
Concentric end at 90° - Ø 80/125 mm
Concentric end at 45° - Ø 80/125 mm
1 m
0.5 m
0.5 m
0.25 m
Maximum permissi le
flue length horizontal
and vertical
Ø mm
60/100
4 m 5 m
Ø mm
0/125
950
50
maximum 4 m.
Vertical terminal
1KWMA83U
Pitch roof slate
1KWMA82U
Extension 60/100
1KWMA56U
Vertical concentric
adaptor 60/100
010006X0
68
95050
50 950
50
1000 125
10
45 mm

20
DOMIcompact F 30 D
Fig. 11
Fig. 12
Connection with two pipe
system
The unit can be connected to a
system of separate air/flue ducts
for a vertical or horizontal outlet
as shown on the drawings 11 - 12
alongside. Numerous accessories
are available on request to meet
the various installation require-
ments. The components used most
frequently are stated in tables.
Please refer to the flue accessory
catalogue or the price list for addi-
tional components.
To check you do not exceed the
maximum permissible duct length,
it is necessary to make a simple
calculation before installation:
1.For each component, tables pro-
vide an “equivalent load loss in linear metres”, depending on
the position of installation of the component (with air inlet or
flue extraction, vertical or horizontal).
The loss is called “equivalent in linear metres” since it is compa-
red to the loss of one metre of duct in air inlet (defined as equal
to 1). For example, a bend at 90° of Ø80 in flue extraction has
an equivalent loss of 2.5 linear metres, i.e. it has a loss equal
to that of 2.5 linear metres of duct in air inlet.
2.After completely defining the layout of the system of split
flues, add up the losses in equivalent metres, depending on
the installation position, of all the components and accessories
in the system.
3.Check that the total calculated loss is less than or equal to 50
equivalent metres, i.e. the maximum permissible for this model
of boiler.
1,5 m
1,0 m
2,0 m
3,0 m
38,0 m
4,0 m
49,5 m
Ref.
1
2
3
4
5
6
No. Pieces
1
1
1
1
38
1
Air bend Ø80
Horizontal air pipe Ø80
Air inlet terminal
Condensate collection cup coupling
Vertical flue pipe Ø80
Vertical terminal
Description Equivalent
loss
Total
1 2 3
4
5
6
Air
Flue