Festool ETS 150/3 EQ User manual

ETS 150/3 EQ
ETS 150/5 EQ
Bedienungsanleitung Exzenterschleifer 4 - 6
Operating Instructions Eccentric sander 7 - 9
Mode demploi Ponceuse excentrique 10 - 12
Instrucciones de servicio Lijadora excéntrica 13 - 15
Istruzioni duso Levigatrice orbitale 16 - 18
Gebruiksaanwijzing Excenterschuurmachine 19 - 21
Bruksanvisning Excenterslipmaskin 22 - 23
Käyttöohje Epäkeskohiomakone 24 - 25
Driftsvejledning Excentersliber 26 - 27
Bruksanvisning Eksentersliper 28 - 29
Instruções de uso Lixadeira excêntrica 30 - 32
Ðóêîâîäñòâî ïî ýêñïëóàòàöèè Ìàøèíêà øëèôîâàëüíàÿ ýêñöåíòðèêîâàÿ 33 - 35
Návod k obsluze Excentrická bruska 36 - 37
Instrukcja obs³ugi Szlifierka mimorodowa 38 - 40
Kezelési utasítás Excenteres csiszológép 40 - 42
Ïäçãßá ëåéôïõñãßáò Åêêåíôñïò ôñï÷éóôÞò 43 - 45
464 774_003
Festool GmbH Wertstr. 20 D-73240 Wendlingen ( 7024/804-0
Seen at Ideal Tools.

CE-Konformitetserklæring. Vi erklærer på eget
ansvar at dette produktet er i overensstemmelse med
følgende normer eller normative dokumenter:
EN 50 144, EN 55 014, EN 61 000 i henhold til bestemmelsene
i direktivene 98/37/EF, 89/336/EØF.
EG-Konformitätserklärung. Wir erklären in alleiniger
Verantwortung, dass dieses Produkt mit den
folgenden Normen oder normativen Dokumenten
übereinstimmt:
EN 50 144, EN 55 014, EN 61 000 gemäß den Bestimmungen
der Richtlinien 98/37/EG, 89/336/EWG.
455 789/200803
EY-standardinmukaisuusvakuutus. Vakuutamme
yksinvastuullisina, että tuote on seuraavien
standardien ja normatiivisten ohjeiden mukainen: EN 50 144,
EN 55 014, EN 61 000 direktiivien 98/37/EY, 89/336/EY
määräysten mukaan.
EG-konformitetsförklaring. Vi förklarar i eget ansvar,
att denna produkt stämmer överens med följande
normer och normativa dokument: EN 50 144, EN 55 014,
EN 61 000 enligt bestämmelserna i direktiven 98/37/EG,
89/336/EEG.
EG-conformiteitsverklaring. Wij verklaren op eigen
verantwoordelijkheid dat dit produkt voldoet aan de
volgende normen of normatieve documenten. EN 50 144,
EN 55 014, EN 61 000 conform de richtlijnen 98/37/EG,
89/336/EEG.
CE-Dichiarazione di conformità. Dichiariamo sotto
la nostra esclusiva responsabilità che il presente
prodotto è conforme alle norme e ai documenti normativi
seguenti: EN 50 144, EN 55 014, EN 61 000 conformemente
alle normative delle direttive 98/37/CE, 89/336/CEE.
Owiadczenie o zgodnoci CE. Niniejszym
owiadczamy z ca³¹ odpowiedzialnoci¹, ¿e wyrób
ten odpowiada nastêpuj¹cym normom wzglêdnie dokumentom
normatywnym: EN 50 144, EN 55 014, EN 61 000 zgodnie z
postanowieniami wytycznych 98/37/EG, 89/336/EWG.
Äçëùóç óõììüñöùóçò ÅÊ. Ìå áíÜëçøç ôçò
óõíïëéêÞò åõèýíçò äçëþíïõìå, üôé ôï ðáñüí ðñïéüí
óõìöùíåß ìå ôá ðáñáêÜôù ðñüôõðá êáé ìå ôá
ðñüôõðá ðïõ áíáöÝñïíôáé óôá ó÷åôéêÜ Ýããñáöá ÅÍ 50 144,
ÅÍ 55 014, EN 61 000 óýìöùíá ìå ôïõò êáíïíéóìïýò
98/37ÅÊ, 89/336/ÅÏÊ
CE-konformitás-nyilatkozat.Kizárólagos
felelõsségvállalás mellett ezennel tanúsítjuk, hogy
a jelen termék megfelel az alábbi szabványoknak ill.
szabványdokumentációnak:
EN 50 144, EN 55 014, EN 61 000 a 98/37EG, 89/336/EWG
irányvonalak rendelkezései szerint.
Leiter Forschung und Entwicklung
Manager Research and Development
Directeur de recherce et développement
Festool GmbH
Wertstr. 20
D-73240 Wendlingen
Dr. Johannes Steimel
EC-Declaration of Conformity: We declare at our sole
responsibility that this product is in conformity with
the following standards or standardised documents:
EN 50 144, EN 55 014, EN 61 000 in accordance with the
regulations 98/37/EC, 89/336/EEC.
CE-Declaração de conformidade: Declaramos, sob
a nossa exclusiva responsabilidade, que este
produto corresponde às normas ou aos documentos
normativos citados a seguir:
EN 50 144, EN 55 014, EN 61 000 segundo as disposições
das directivas 98/37/CE, 89/336/CEE.
CE-Déclaration de conformité communautaire. Nous
déclarons sous notre propre responsabilité que ce
produit est conforme aux normes ou documents de
normalisation suivants: EN 50 144, EN 55 014, EN 61 000
conformément aux prescriptions des directives 98/37/CE,
89/336/CEE.
Çàÿâëåíèå î êîíôîðìíîñòè ÑÅ. Ìû çàÿâëÿåì â
åäèíîëè÷íîé îòâåòñòâåííîñòè, ÷òî äàííîå èçäåëèå
ñîîòâåòñòâóåò òðåáîâàíèÿì ñëåäóþùèõ ñòàíäàðòîâ èëè
íîðìàòèâîâ: EN 50 144, EN 55 014, EN 61 000 â ñîîòâåòñòâèè
ñ ïîñòàíîâëåíèÿìè äèðåêòèâ ÅÑ 98/37, ÅÝÑ 89/336.
CE-Declaración de conformidad. Declaramos bajo
nuestra exclusiva responsabilidad que este
producto corresponde a las siguientes normas o documentos
normalizados: EN 50 144, EN 55 014, EN 61 000 conforme a
las prescripciones estipuladas en las directrices 98/37/CE,
89/336/CEE.
Prohláení o souladu s normami CE. Prohlaujeme
na vlastní zodpovìdnost, e tento výrobek odpovídá
následujícím normám nebo normativním dokumentùm:
EN 50 144, EN 55 014, EN 61 000 v souladu s ustanoveními
smìrnic 98/37/EHS, 89/336/EHS.
EF-konformitetserklæring: Vi erklærer at have alene
ansvaret for, at dette produkt er i overensstemmelse
med de følgende normer eller normative dokumenter:
EN 50 144, EN 55 014, EN 61 000 i henhold til bestemmelserne
af direktiverne 98/37/EF, 89/336/EØF.
Seen at Ideal Tools.

Seen at Ideal Tools.

7
1Before using sander
1.1 Safety instructions
Read the safety instructions on the
attached sheet before using the sander.
Always wear protective goggles
because of possible dangers when
sanding.
The manufacturers handling and processing
instructions must be observed without fail if
explosive or self-igniting dusts are likely to
occur during sanding.
The electric tool must be connected to a
suitable dust extraction unit and applicable
safety regulations must be observed if dusts
dangerous to health are likely to occur during
sanding.
Wear a dust mask for your own safety.
1.2 Correct usage
The sanders are designed for sanding wood,
plastic, composite materials, paint / varnish,
filling material and similar materials.
Metal and materials with an asbestos content
must not be processed with these tools.
The machines must not be damp nor operated
in a damp environment for electrical safety
reasons. The machines may only be used for
dry sanding.
The user bears sole responsibility for any
damage or accidents resulting from incorrect
use.
1.3 Noise and vibration information
Typical values established in compliance with
EN 50 144:
Sound pressure level 72 dB(A)
Measured acceleration 6.0 m/s²
The noise level can exceed 85 dB(A)
during work.
Wear ear protectors!
2Electrical connection and operation
The mains voltage must correspond
with the voltage on the rating plate!
Switch (1.2) is an on/off switch.
For continuous use it can be engaged with the
lateral locking button (1.3). Pressing the switch
again releases the lock.
See Fig. 3 for connection and disconnection of
the power cable.
3Electronic control
The ETS 150/3 EQ, ETS 150/5 EQ has
an electronic control with which the
rotational speed can be varied step-
free.
This allows the sanding speed to be adapted
to the optimum level according to the material
concerned.
The speed is set using the rotary control button
(1.1).
The numbers on the rotary control button
represent approximately the following stroke/
orbit speeds:
112,000 rpm 4 17,500 rpm
214,000 rpm 519,000 rpm
316,000 rpm 621,000 rpm
4Dust extraction
Dust extractors prevent large
accumulations of dust in the air in the
working environment and dirt collecting
in the workplace.
4.1 Inboard extraction
The machines are fitted with inbuilt extraction
as standard.
The sanding dust is extracted through suction
openings in the sanding base (1.13) and
trapped in the turbo-filter (1.5).
The turbo-filter has to be changed when it is
so full of dust that the extraction power
diminishes.
Technical data ETS 150/3 EQ ETS 150/5 EQ
Wattage 310 W 310 W
Speed 6,000 - 10,000 rpm 6,000 - 10,000 rpm
Power stroke 12,000 - 21,000 rpm 12,000 - 21,000 rpm
Sanding stroke 3.0 mm 5.0 mm
Sanding base Ø 150 mm Ø 150 mm
Weight 1.8 kg 1.8 kg
Degree of protection / II / II
The specified illustrations can be found at the beginning of the operating instructions.
Seen at Ideal Tools.

8
Inserting a turbo-filter
-Push the front cardboard section of the tur-
bo-filter with the sealing lip (1.4) onto the
extraction nozzle (1.9) of the filter holder
-Insert rear cardboard section with slot (1.6)
onto the retaining strip (1.7) of the filter hol-
der
-Push the filter holder with its opening (1.11)
as far as it will go onto the extraction nozzle
(1.12) of the machine and clamp tight by
turning rotary knob (1.10).
4.2 External extraction by an extraction
unit
In order to avoid frequent changing of the tur-
bo-filter when carrying longer sanding jobs, it
is possible to connect a Festool extractor to
the unit instead of using inbuilt extraction.
In this case, the extraction pipe (Ø 27 mm
(1.8)) of the extraction unit is connected to
the suction nozzle (1.12).
5Choice and installation of the
sanding disks
5.1 Choice of sanding disk
The appliance can be fitted with three sanding
disks of different hardness depending on the
surface to be treated.
Hard: coarse sanding on surfaces, sanding
at edges.
Soft: universal for coarse and fine
sanding, for flat and curved surfaces.
Super-soft: fine sanding on formed parts,
curves, radii. Do not use on edges!
5.2 Assembly
The sanding disks and the tool-holding fixture
on the appliance are equipped with a positive
holder (2.1).
Make sure the sanding disk is correctly
positioned before screwing it tight.
For safety reasons, only use original
Festool sanding disks!
6Attaching sanding material
The appropriate Stickfix sanding paper and
Stickfix sanding felt can be fastened quickly and
easily onto the Stickfix sanding base.
Always use original Festool sanding
materials!
The self-adhesive sanding material (1.14) is
simply pressed onto the sanding base (1.13)
and held safely in place by the Stickfix sanding
base velcro surface.
7Operating instructions
Never overload the tool by using too
much pressure!
The best sanding results are achieved when
applying moderate pressure.
The ETS 150/3 EQ gives the best surface quality
and low abrasion.
The ETS 150/5 EQ provides high abrasion with
good surface quality.
The sanding performance and quality depend
mainly on the choice of the right sanding
material.
Festool offers the appropriate sanding material
for all applications (seeFestool catalogue or on
the Internet under www.festool.com).
We recommend the following settings on
the rotary control (1.1) for electronic
machines:
rotary control setting
- sanding work
5 - 6
-sanding with max. drive
-sanding old paint
-sanding wood and veneer prior to painting
-interim sanding of paint on surfaces
4 - 5
-sanding of thinly applied primer
-sanding of wood with sanding vlies
-sanding edges on wooden parts
-smoothing primed wooden surfaces.
3 - 4
-sanding full wooden and veneer edges
-sanding in the grooves/rebates of windows
and doors
-interim paint sanding on edges
-pre-sanding natural wood windows with
sanding vlies
-smoothing wood surfaces with sanding felt
prior to staining
-rubbing down stained surfaces with sanding
vlies
-rubbing down or removing excess lime paste
with sanding vlies
2 - 3
-interim paint sanding on stained surfaces
-cleaning natural wood window grooves with
sanding felt
1 - 2
-sanding stained edges
-sanding thermoplastic synthetics
Seen at Ideal Tools.

9
8Sanding base brakes
The sanding base is braked by a collar (2.2) in
order to prevent any uncontrolled excessive
speed of the sanding base.
Because the collar wears down in the course
of time, it has to be replaced by a new one
(order no. 453 388) as soon as there is any
reduction in the braking effect.
9Maintenance and care
Always remove the plug from the
mains supply socket before carrying
out any work on the machine!
The cooling air vents on the motor housing
must always be free of blockages and clean to
ensure air circulation.
Any maintenance or repair work requiring the
motor housing to be opened may only be
carried out by an authorised service workshop.
10 Warranty
Our equipment is under warranty for at least
12 months with regard to material or
production faults in accordance with national
legislation.
In the EU countries, the warranty period f is
24 months (an invoice or delivery note is
required as proof of purchase).
Damage resulting from, in particular, normal
wear and tear, overloading, improper handling,
or caused by the user or other damage caused
by not following the operating instructions, or
any fault acknowledged at the time of
purchase, is not covered by the warranty.
Complaints will only be acknowledged if the
equipment has not been dismantled before
being sent back to the suppliers or to an
authorised Festool customer support
workshop.
Store the operating instructions, safety notes,
spare parts list and proof of purchase in a safe
place. In addition, the manufacturers current
warranty conditions apply.
Note
We reserve the right to make changes to the
technical data contained in this information as
a result of ongoing research and development
work.
Seen at Ideal Tools.

Festool GmbH
Postfach 1163
D-73236 Wendlingen
Wertstraße 20
D-73240 Wendlingen
)(07024) 804-0
Fax [phone]
http://www.festool.com
Seen at Ideal Tools.