Festool ROTEX RO 150 FEQ Installation instructions

Originalbetriebsanleitung - Getriebe-Exzenterschleifer 6
Original operating manual - Gear-driven eccentric sander 10
Notice d’utilisation d’origine - Ponceuse roto-excentrique 14
Manual de instrucciones original - Lijadora excéntrica de engranaje 18
Istruzioni per l’uso originali - Levigatrice orbitale a motoriduttore 22
Originele gebruiksaanwijzing - Roterend-excentrische schuurmachine 26
Originalbruksanvisning - Transmissions-excenterslip 30
Alkuperäiset käyttöohjeet - Vaihteella varustettu epäkeskohiomakone 34
Original brugsanvisning - Excentersliber 38
Originalbruksanvisning -Slipe- og poleringsmaskin 42
Manual de instruções original - Lixadora excêntrica de engrenagem 46
Оригинал Руководства по эксплуатации - Эксцентриковая шлифмашинка с редуктором 50
Originál návodu k obsluze -Excentrická bruska spřevodovkou 54
Oryginalna instrukcja eksploatacji -Przekładniowa szlifierka mimośrodowa 58
ROTEX
RO 150 FEQ
RO 150 FE
468 064_014

EG-Konformitätserklärung. Wir erklären in alleiniger Verantwortung,
dass dieses Produkt mit allen relevanten Anforderungen folgender Richtlinien,
Normen oder normativen Dokumenten übereinstimmt: 2006/42/EG, 2004/108/
EG (bis 19.04.2016), 2014/30/EU (ab 20.04.2016), 2011/65/EU, EN 60745-
1:2009, EN 60745-2-4:2009+A11:2011, EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:1997+Corrigendum 1997+A1:2001+A2:2008, EN
61000-3-2:2006+A1:2009+A2:2009, EN 61000-3-3:2013.
EC-Declaration of Conformity: We declare under sole responsibility
that this product complies with all the relevant requirements in the follow-
ing Directives, standards and normative documents: 2006/42/EG, 2004/108/
EG (until 19.04.2016), 2014/30/EU (from 20.04.2016), 2011/65/EU, EN 60745-
1:2009, EN 60745-2-4:2009+A11:2011, EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:1997+Corrigendum1997+A1:2001+A2:2008, EN
61000-3-2:2006+A1:2009+A2:2009, EN 61000-3-3:2013 .
Déclaration de conformité CE. Nous certifions, sous notre propre res-
ponsabilité, que ce produit satisfait aux exigences des directives, normes ou
documents correspondants suivants : 2006/42/CE, 2004/108/CE ((jusqu‘au
19.04.2016), 2014/30/UE (à partir du 20.04.2016), 2011/65/UE, EN 60745-
1:2009, EN 60745-2-4:2009+A11:2011, EN 55014-1:2006+A1:2009+A2:2011,
EN 55014-2:1997+Corrigendum1997+A1:2001+A2:2008, EN
61000-3-2:2006+A1:2009+A2:2009, EN 61000-3-3:2013 .
Declaración de conformidad CE. Declaramos bajo nuestra res-
ponsabilidad que este producto cumple todos los requisitos relevan-
tes de las siguientes directivas, normas o documentos normativos:
2006/42/CE, 2004/108/CE (hasta el 19.04.2016), 2014/30/UE (a partir del
20.04.2016), 2011/65/UE, EN 60745-1:2009, EN 60745-2-4:2009+A11:2011,
EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+Corrigen-
dum1997+A1:2001+A2:2008, EN 61000-3-2:2006+A1:2009+A2:2009, EN
61000-3-3:2013 .
Dichiarazione di conformità CE. Dichiariamo sotto nostra unica responsabilità
che il presente prodotto è conforme a tutti i requisiti di rilevanza definiti dalle seguenti
direttive, norme o documenti normativi: 2006/42/CE, 2004/108/CE (fino al 19.04.2016),
2014/30/UE (a partire dal 20.04.2016), 2011/65/UE, EN 60745-1:2009, EN 60745-2-
4:2009+A11:2011, EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+Corrigendum
1997+A1:2001+A2:2008, EN 61000-3-2:2006+A1:2009+A2:2009, EN 61000-3-3:2013.
EG-conformiteitsverklaring. Wij verklaren en stellen ons ervoor ver-
antwoordelijk dat dit product volledig voldoet aan de volgende normen
en normatieve documenten: 2006/42/EG, 2004/108/EG (tot 19.04.2016),
2014/30/EU (vanaf 20.04.2016), 2011/65/EU, EN 60745-1:2009, EN 60745-2-
4:2009+A11:2011, EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+Cor-
rigendum1997+A1:2001+A2:2008, EN 61000-3-2:2006+A1:2009+A2:2009, EN
61000-3-3:2013
.
EG-förklaring om överensstämmelse. Vi förklarar på eget ansvar
att denna produkt uppfyller alla krav enligt följande direktiv, normer el-
ler normgivande dokument: 2006/42/EG, 2004/108/EG (till 19.04.2016),
2014/30/EU (fr o m 20.04.2016), 2011/65/EU, EN 60745-1:2009, EN 60745-2-
4:2009+A11:2011, EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+Cor-
rigendum1997+A1:2001+A2:2008, EN 61000-3-2:2006+A1:2009+A2:2009, EN
61000-3-3:2013 .
Getriebe-Exzenterschleifer
Gear-drive eccentric sander
Ponceuse
Serien-Nr.
Serial no.
N° de série
RO 150 FE 497021
RO 150 FEQ 492160, 493974
Jahr der CE-Kennzeichnung:
Year of CE mark:
Année du marquage CE :
2005

1
2
1.4 1.3 1.8
1.1
1.2
1.5 1.6 1.7
0I

5.3
3.1
4.1
5.1 5.4
5.2
4.2
4
5
3

10
Gear-drive eccentric sander
Technical data RO 150 FEQ/RO 150 FE
Power 720 W
Speed 3300 - 6800 rpm
Sanding stroke 5 mm
Weight (excluding cable) 2.3 kg
Degree of protection /II
The specified illustrations can be found at the
beginning of the operating instructions.
Graphical symbols
Caution. Danger!
Read the operating instructions/notes
Wear ear protection!
Wear protective goggles!
Wear a protective mask!
Disconnect from the power supply!
1 Intended use
As specified, the machines are designed for sand-
ing and polishing wood, plastic, metal, composite
materials, paint/varnish, filler and similar mate-
rials.
Materials containing asbestos must not be pro-
cessed.
For reasons of electrical safety the machine must
not be damp nor operated in a humid environment.
The machine may only be used for dry sanding.
The user is liable for damage and injury
resulting from incorrect usage!
2 Before starting up, please observe the
following
2.1 Safety instructions
WARNING! Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
- Harmful/toxic dusts can occur during your work
(e.g. lead-containing paint, some types of wood
and metal). Contact with these dusts, espe-
cially inhaling them, can represent a hazard for
operating personnel or persons in the vicinity.
Comply with the safety regulations that apply in
your country. Connect the electric power tool to
a suitable extraction system.
To protect your health, wear a P2 protec-
tive mask.
Always wear protective goggles because
of possible dangers when sanding.
- The manufacturer’s handling and processing
instructions must be observed without fail if
explosive or self-igniting dusts are likely to oc-
cur during sanding.
- Prevent the penetration of liquid polish into
the tool. The penetration of liquid polish into
the power tool increases the risk of an electric
shock.
- If the power tool is dropped or falls, check
for damage to the machine and sanding pad.
Remove the sanding pad for closer inspection.
Repair damaged parts before using again. Bro-
ken sanding pads and damaged machines can
cause injuries and machine instability.
- Only for AS/NZS: The tool shall always be sup-
plied via residual current device with a rated
residual current of 30 mA or less.
2.2 Noise and vibration information
The typical values determined in accordance with
EN 60745 (see EU Declaration of Conformity) are:
Sound pressure level 82 dB(A)
Sound-power level 93 dB(A)
Measuring uncertainty allowance K = 3 dB
Wear ear protection!
Vibration emission value ah(vector sum for three
directions) and uncertainty K measured in ac-
cordance with EN 60745 (see EU Declaration of
Conformity):
Fine sanding a
h= 4,0 m/s²
Auxiliary handle ah= 6,5 m/s²
K = 2,0 m/s²
Coarse sanding ah= 3,5 m/s²
Auxiliary handle ah= 5,0 m/s²
K = 2,0 m/s²
Polishing ah= 5,0 m/s²
Auxiliary handle ah= 8,5 m/s²
K = 2,5 m/s²

11
The specified emissions values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary
estimates regarding vibration and noise loads
during operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with oth-
er insertion tools or if not maintained adequately.
Take note of idling and downtimes of machine!
3 Power supply and start-up
The mains voltage must correspond to
the specification on the rating plate.
The slide switch (1.2) serves as an On/Off switch
(I = ON, 0 = OFF).
Only RO 150 FEQ: See Fig. 2 for connection and
disconnection of the power cable.
Always switch the machine off before con-
necting or disconnecting the mains lead!
4 Electronics
The machine has full-wave electronics
with the following features:
Smooth start-up
The smooth start-up ensures the machine starts
up jolt-free.
Speed adjustment
You can regulate the speed steplessly between
3300 and 6800 rpm using the adjusting wheel (1.4).
This enables you to optimise the cutting speed to
suit the material.
Constant speed
The pre-selected speed remains constant whether
the machine is in operation or in neutral position.
Temperature control
If the motor temperature becomes too high, the
power supply and speed are reduced. The tool
then only runs with reduced power to enable
rapid cooling by means of the motor ventilation.
After cooling down, the tool accelerates again
automatically.
5 Machine settings
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
5.1 Sanding motion
You can use the switch (1.1) to set two different
sanding motions.
The change can only be made when the
sanding pad is stationary, as the switch
is locked in place during operation for
reasons of safety.
Rotex rotary motion (coarse sanding, polishing)
The Rotex rotary motion is a combina-
tion of rotary and eccentric motions. This
position is selected for sanding with high
output (coarse sanding) and polishing.
Slide the switch (1.1) into the right position.
Eccentric motion (fine sanding)
This position is selected for sanding with
low output for a scratch-free surface (fine
sanding).
Press the switch (1.1) downwards and push it into
the left-hand position.
5.2 Sanding pad brake
The rubber collar (3.1) prevents the sanding
pad from revving up to maximum speed in an
uncontrolled manner during eccentric motion
(fine sanding). Because the collar wears down
in the course of time, it has to be replaced by a
new one (order no. 465 472) as soon as there is
any reduction in the braking effect. When fitting
a new rubber collar (3.1), make sure it is in the
correct position.
5.3 Choice and installation of the sanding
disks
Choise of sanding disk
The appliance can be fitted with three sanding
disks of different hardness depending on the
surface to be treated.
Hard: coarse and fine sanding on surfaces. Sand-
ing at edges.
Soft: universal for coarse and fine sanding for flat
and curved surfaces.
Super-soft: fine sanding on formed parts, curves,
radii. Do not use on edges!
Assembly
The FastFix system enables tool-free replacement
of the sanding pad:
- Set the switch (1.1) to the right, to the Rotex
rotary motion
- Press spindle stop (1.6),
- Turn the fitted sanding pad from the spindle
(right-handed thread)
- Keep the spindle stop pressed down and screw
on the new sanding pad up to the stop (until
it can be turned no more). Make sure that the
rubber collar (3.1) is fitted correctly when doing
this.

12
- let go of the spindle stop
Actuate the spindle stop only when the drive spin-
dle is stationary. Do not switch on the motor when
the spindle stop is pressed in.
5.4 Attaching sanding material
The appropriate Stickfix sanding paper and Stick-
fix sanding felt can be fastened quickly and easily
onto the Stickfix sanding base.
The self-adhesive sanding material is simply
pressed onto the sanding base (1.7) and held
safely in place by the Stickfix sanding base vel-
cro surface. After use, the StickFix sandpaper is
simply pulled off.
5.5 Securing polishing attachments
To prevent damage, PoliStick polishing attach-
ments (sponges, felt, lambswool bonnets) may
only be used on the special polishing pad that is
fitted on the machine instead of a sanding pad. In
the same way as the StickFix abrasives, the Poli-
Stick polishing attachments are simply pressed
onto the polishing pad and pulled off after use.
5.6 Dust extraction
Always connect the machine to a dust
extractor when performing work that
generates dust.
You can connect a Festool extractor with an ex-
tractor hose diameter of 27 mm to the extractor
connector (1.5). The extraction adapter (4.1) can
be removed for polishing work. To do this, press
the locking button (4.2), draw the extraction
adapter backwards and pull off. To reattach the
extraction adapter, insert it as shown in Fig. 4 and
slide it towards the sanding pad until the locking
button (4.2) latches into place.
5.7 Edge protector
The edge protector (5.1) prevents the sanding pad
from touching the edge perpendicular to a surface
(e.g. when sanding along a wall), thereby prevent-
ing the machine from rebounding.
Assembly
Slide the edge protector onto the guide groove
(5.3) on the machine until it latches into place.
5.8 Auxiliary handle
The auxiliary handle (Accessories, 5.2) can be
screwed onto either the right or left of the gear
head.
5.9 Ball grip
The ball grip (partly as an accessory, 5.4) reduces
stress during demanding polishing and sanding
applications.
Assembly:
Slide the ball grip into the guide slot (5.3) on the
machine until it engages in position.
6 Working with the machine
Always secure the workpiece in such a
manner that it cannot move while being
sawed.
For safe guidance, hold the machine with both
hands on the motor housing (1.3) and on the gear
head (1.8) and/or the auxiliary handle (Accesso-
ries, 5.2).
Never overload the tool by using too much pres-
sure! The best sanding results are achieved when
applying moderate pressure. The sanding perfor-
mance and quality depend mainly on the choice
of the right sanding material.
Tables A and B show the settings we recommend
for different sanding and polishing work.
6.1 Metalworking
The following precautions are to be taken
when processing metals for safety rea-
sons:
- Pre-connect a residual current circuit-breaker
(FI, PRCD).
- Connect the machine to a suitable dust extractor.
- Clean tool regularly of dust accumulations in
the motor housing.
Wear protective goggles.
7 Accessories, tools
For your own safety, use only original
Festool accessories and spare parts.
Festool offers the appropriate accessories, sand-
ing and polishing attachments for every applica-
tion.
The accessory and tool order number can be found
in the Festool catalogue or on the Internet under
”www.festool.com”.
8 Maintenance and care
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
All maintenance and repair work which
requires the motor casing to be opened
may only be carried out by an authorised
service centre.

13
Sponge, fine,
honeycombed
Customer service and repair. Only
through manufacturer or service work-
shops: Please find the nearest address
at:: www.festool.com/Service
EKAT
1
235
4
Use only original Festool spare parts!
Order No. at: www.festool.com/Service
The cool air openings in the motor casing must
always be kept clean and unobstructed to ensure
air circulation. The tool is fitted with special mo-
tor brushes with an automatic cut-out. When the
brushes become worn the power supply is shut off
automatically and the tool comes to a standstill.
9 Disposal
Do not throw the power tool in your household
waste! Dispose of the machine, accessories and
packaging at an environmentally-responsible recy-
cling centre! Observe the valid national regulations.
EU only: In accordance with European Directive on
waste electrical and electronic equipment and im-
plementation in national law, used electric power
tools must be collected separately and handed in
for environmentally friendly recycling.
Information on REACh: www.festool.com/reach