Fiamo Loft Twin Bed Complete User manual

Loft Twin Bed Complete with Ladder on the left
Loft Twin Bed Complete with Ladder on the right
US-CA-EN
MADE IN VIETNAM
Bulletin NO.: 147642-00-CA-EN
1
IMPORTANT! Please keep these instructions for future reference. Please read
these instructions before assembly and use of this product.
• Adult assembly is required.
• Allen wrench (included) required for assembly.
• Product features and decorations may vary from illustrations.
• Do not use power drills or drivers.
• Phillips Head Screwdriver (Not included) required for assembly

A1:
Post 1 x2pcs A2: Post 2 x2pcs
A3:
Headboard
Bottom Rail x2pcs
A4:
Headboard Middle Panel x2pcs
B1: Front Bed Rail x1pc
A5:
Headboard Top Rail x2pcs
C1:
Front
Horizontal Rail x2pcs
C3:
Back
Horizontal Rail x2pcs
B2: Back Bed Rail x1pc C4:
Back
Vertical Rail x1pc
E1:
Ladder Left Post x1pc E2:
Ladder Right Post x1pc E3:
Ladder Step x3pcs
D:
Slats Roll x1Set
Part List
C2:
Front
Vertical Rail x1pc
2

A1
A2
A2
A1
B1
B2
C2
C1
C4
D
A3
A5
A4
A5
A4
A1: Post 1 x2pcs
A2: Post 2 x2pcs
A3
A3: Headboard Bottom Rail x2pcs
A4:
Headboard Middle Panel x2pcs
A5:
Headboard Top Rail x2pcs
B1: Front Bed Rail x1pc
B2: Back Bed Rail x1pc
C1:
Front Horizontal Rail x2pcs
C2:
Front Vertical Rail x1pc
C3:
Back Horizontal Rail x2pcs
C4:
Back Vertical Rail x1pc
D: Slats Roll x1Set
E1:
Ladder Left Post x1pc
E2:
Ladder Right Post x1pc
E1
C3
E2
E3
E3
E3
E3:
Ladder Step x3pcs
Part List
3

Ø1/4" x 3" Allen Head Bolt x16
1
Ø1/4" x 2" Allen Head Bolt x12
2
Ø1/4" x 1-3/8" Allen Head Bolt x12
3
Crescent Nut x8
5
7
3/4" Flat Head Screw x2
8
1-1/4" Phillip Head Screw x29
9
Allen Wrench x1
10
1-1/4" Wood dowel x16
6
1-5/8" Wood dowel x4
Part List
HARDWARE AND TOOL DIAGRAM
Ø1/4" x 1-5/8" Allen Head Bolt x6
4
4
Screwdriver (Not included)

5
Furniture Care Instructions
Room Climate Control
Wood, when first cut contains more than 50 percent water. When it is prepared for furniture
construction it is placed in a Kiln and the moisture content is brought down to 8 to 10 percent. Wood
is porous and responds to its environment. If the room has high humidity it will absorb it and expand
and if the humidity is low it will lose moisture and shrink.
It is important that the humidity levels in the room be controlled from extremes of too much
humidity or too little. Furniture should not be placed close to air-conditioning outlets, fireplaces,
radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of
temperature and humidity can damage any fine wood product.
The Ideal Environment for Fine Furniture
Fine wood furniture will have fewer problems when its environment is controlled at a temperature
between 65 and 75 degrees and a relative humidity between 35 and 40 percent. Wood placed in an
environment outside of those limits can and will shrink or expand and may develop some small
cracks which are not material or structural defects.
Sticking Doors and Drawers
With minor changes in temperature and humidity, doors and drawers may swell and be
difficult to open or close. Tolerances have been built into the units but extreme conditions may still
cause sticking. This will adjust back to normal over time but until it does, consider using a
dehumidifier or rub candle wax or paraffin on the sides that stick.
Avoid Direct Sunlight
Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some cases
darken them. It can also cause crazing or hair line cracks in the finish. White finishes will yellow
naturally over time and exposure to direct sunlight will hasten this natural process along with some
woods darkening naturally over time; this is not considered to be a quality defect.
Proper Storage
If you need to put your furniture in storage for any period of time, do not place furniturein a damp
basement or hot dry attic. Allow air movement around the furniture and do not stack anything on it.
In General
Protect furniture surface from hot or extremely cold items.
Use coasters under hot or cold beverages.
Do not use synthetic fabric under accessories or lamps.
Protect tops from pens, markers and crayons.
Oils from potpourri and other scented items can damage the furniture finish.
Do not drag items across the surface of the furniture.
Allow the surface to breath by rotating your accessories and lamps.
Do not over polish the furniture, do it only two or three times a year. Over polishing can
distort the natural finish of the product.
Do not wax the furniture as wax build up can destroy the natural finish of the product.
When moving furniture always lift the unit. Do not push or drag it to avoid damage to the legs.
Keep the furniture level so doors and drawers open and close freely.
Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.

6
STOP
IF YOU EXPERIENCE ANY
ISSUES WITH THIS PRODUCT
BEFORE YOU
RETURN THIS TO
THE RETAILER
PLEASE FOLLOW
PROCEDURES ON THE
BACK PAGE

7
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT OR FALLS:
1. FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK END
STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM BED.
2. ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH,
TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALL.
3. SURFACE OF MATTRESS MUST BE AT LEAST 5 INCHES (127MM) BELOW THE UPPER
EDGE OF GUARDRAILS.
4. DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
5. PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER, AND OTHER
COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL
CONNECTORS ARE TIGHT.
6. DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED.
7. PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
8. ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
9. DO NOT USE SUBSTITUTE PARTS. CONTACT THE MANUFACTURER OR DEALER FOR
REPLACEMENT PARTS.
10. USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD USING
THE UPPER BUNK.
11. ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK.
IF THE BUNK BED WILL BE PACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS
THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT
ENTRAPMENT BETWEEN THE BED AND WALL.
12. THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
13. USE ONLY MATTRESS WHICH IS 74-75 INCHES LONG AND 37 1/2- 38 1/2 INCHES WIDE
ON UPPER BUNK.
14. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
WARNINGS
STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE
BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT NOT
LIMITED TO, HOOKS, BELTS, AND JUMP ROPES.
SIZE OF MATTRESS AND FOUNDATION:
USE ONLY MATTRESS WHICH IS 74"-75" LONG AND 37 1/2" - 38 1/2" WIDE ON UPPER BUNK.
ENSURE THICKNESS OF MATTRESS DOES NOT EXCEED 8" AND MATTRESS IS AT LEAST 5"
BELOW UPPER EDGE OF GUARDRAILS.
!

Ø1/4" x 1-1/4" Wood dowel x16
6
Ø1/4" x 3" Allen Head Bolt x8
1
1
6
6
1
1
1
A2
A2
A1
A1
A3
A4
A5
A3
A4
A5
A1: Post 1 x2pcs
A2: Post 2 x2pcs
A3: Headboard Bottom Rail x2pcs
A4:
Headboard Middle Panel x2pcs
A5:
Headboard Top Rail x2pcs
Allen Wrench x1
10
6
6
6
6
6
6
1
1
1
8
1
ASSEMBLY STEP 1 ( LOFTBED)

9
B1: Front Bed Rail x1pc
B2: Back Bed Rail x1pc
C3:
Back Horizontal Rail x2pcs
Ø1/4" x 3" Allen Head Bolt x8
1
Ø1/4" x 2" Allen Head Bolt x8
2
Allen Wrench x1
10
1
1
1
1
2
2
B1
B2
C3
7
7
7
7
Crescent Nut x8
5
5
5
5
71-5/8" Wood dowel x4
ASSEMBLY STEP 2 ( LOFT BED)

10
ASSEMBLY STEP 3 ( LOFT BED)
Ø1/4" x 1-5/8" Allen Head Bolt x6
3
C2:
Front Vertical Rail x1pc
C2
3
3
C2
2
3
2
3
For attaching Ladder on the RIGHT side of the Loft Bed
For attaching Ladder on the LEFT side of the Loft Bed
For attaching Ladder on the RIGHT side of the Loft Bed
For attaching Ladder on the LEFT side of the Loft Bed
Note: before attaching Front Vertical Guardrail (C2) decide which side of the bunk bed you would like the ladder on.
Follow the diagrams on the left side for attaching the ladder on the left.
Follow the diagrams on the right side for attaching the ladder on the right.
Allen Wrench x1
10
Ø1/4" x 2" Allen Head Bolt x4
2

11
Ø1/4" x 1-3/8" Allen Head Bolt x12
4
E1:
Ladder Left Post x1pc
E2:
Ladder Right Post x1pc
E3:
Ladder Step x3pcs
E2
E1 4
4
4
4
4
4
E3
E3
E3
Allen Wrench x1
10
ASSEMBLY STEP 4 ( LOFT BED)

12
Ladder on the right side of the Loft Bed
Ladder on the left side the Loft Bed
8
3/4" Flat Head Screw x2
8
ASSEMBLY STEP 5 ( LOFT BED)

13
1-1/4" Phillip Head Screw x29
9
C4:
Back Vertical Rail x1pc
D: Slats Roll x1Set
C4
9
9
D9
Loftbed Complete with Ladder on the left Loftbed Complete with Ladder on the right
9
9
ASSEMBLY STEP 6 ( LOFT BED)

14
LOFT BED COMBINE WITH SLIDING DESK &
HUTCH & 3 DRAWER CHEST
SLIDING DESK
3 DRAWER CHEST
LOFT BED
HUTCH
LADDER ON THE LEFT LADDER ON THE RIGHT
MAX WEIGHT ON BED: 300LBS
!
300
lbs

15
Most inquiries can be answered by visiting our website. There, you can
order parts, find assembly instructions, and get answers to frequently
asked questions on all of our brands.
You can also email us. In order for us to provide you with the best service possible, please
include the following information in your email:
1. Your Name
2. Address
3. Phone Number
4. Item Number and description of your product
5. PO#
6. Production Date
All product information will be on the product label located on the back of
all dressers and other furniture, and on either the inside bottom of the headboard, crib
ends, or stabilizer bar of your crib, depending on which model you have.
Someone will contact you via e-mail or phone to help you with your issues.
If you do not have internet access, you can fax your information to us.
If you do not have internet or fax access, please call us at our toll free number.
Be sure to have all of the above information ready to give to your Customer Service Specialist.
Product Assistance Procedures
Procedures to follow should you have any questions:
You have purchased a quality piece of furniture. Our International team has spent
many hours designing and engineering this piece and packaging to ensure you will
be satisfied with your purchase. But if for any reason you need help with your
purchase please contact us at any time.
Manufactured for and distributed in the United States & Canada by: Bivona & Company®, LLC
LLC 701 Boutwell Rd, Suite A-3, Lake Worth Florida.
Contact
U.S.A & CANADA
Bivona & Company®, LLC
701 Boutwell Rd, Suite A-3, Lake Worth Florida.
Toll Free: 1-888-963-8125
Fax: [phone]
Zip code : 33461
Website: www.bivonaco.com
Email: [email protected]
MADE IN VIETNAM