Dream On Me 665 User manual

Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed are step by step instructions to help you.
quickly assemble your product.Before you begin we recommend
that you follow the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver Hammer
Do Not Use Power Drills or Drivers
To protect parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
ASSEMBLY INSTRUCTIONS
ITEM NO: 665
1
s
Read all instructions before assembling crib.
Save instructions for future use.
Dream On Me Inc.
1532 S WASHINGTON AVE
PISCATAWAY TWP NJ 08854
OFFICE: 732-752-7220
CUSTOMER SERVICE: 732-366-1788

2

.Read all instructions before assembling crib, keep instructions for future use.
.Upon completion of assembly be sure all screws, bolts and fastening devices have been
securely tightened. A frequent check should be made.
.Infants can suffocate in gaps between a mattress too small or too thick and product sides,
on soft bedding never add a mattress, pillow,comforter or padding.
.CAUTION: Any mattress used in this crib must be at least 27-1/4inches(690mm) by 51-5/8
inches(1310mm),with a thickness not exceeding 6 inches(150mm), the dimensions of the
.Failure to follow these warnings and instruction could result in serious injury or death.
.Never use plastic shipping bag or other plastic film as mattress covers not sold and
intended for that purpose, as they can cause suffocation .
.Strings can cause strangulation! Never place items with a string around a child’s neck,
.Never use this product if there are any loose or missing fasteners, loose joints,broken
parts, or torn mesh/fabric. check before assembly and periodically during use.
Contact DREAM ON ME for replacement parts and instructional literature if needed.
.Never substitute parts, the product including side rails, must be fully erected prior to use.
.Discontinue use of the product when child is able to climb out or reaches the height of
.When child is able to pull to standing position,set mattress/base to lowest adjustment
position and remove bumper pads, large toys,and other objects that could serve as steps
for climbing out. A child can trap parts of the body or clothing on loose fasteners .
.Never use a water mattress with this product.
.If refinishing,use a non-toxic finish specified for children’s products.
.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
back to sleep, unless otherwise advised by your physician.
WARNING !
.Never place product near window where cords from blinds or drapes can strangle a child.
MADE IN CHINA
35in (890mm).
mattress shall be taken from seam to seam or edge to edge where appropriate.
such as hood strings or pacifier cords. Never suspend strings over product or attach
strings to toys.
.Infants can suffocate on soft bedding .
.Never add a pillow or comforter .
.Never place additional padding under an infant .
.To help prevent strangulation tighten all fasteners.
.A child can trap parts of the body or clothing on loose fasteners.
.Follow warnings on all products in a crib .
See head panel & mattress support of the product for warnings.
Replace teething rail if damaged,cracked or loose.
3

=
4

5

6
CONNECTION HARDWARE
a : 1/4”x3” Allen head bolt (14 pcs)
e : 1/4”x2” Allen head bolt (16 pcs) f: 1/4”x3/4” Allen head bolt (4 pcs) g:Allen wrench (1pc)
b: Barrel nuts (14 pcs) c: Wood dowels (18 pcs) d: 1/4”x1-3/8” Allen head bolt (3 pcs)
PARTS ENCLOSED IN CARTON
ALeft head board
h:Washer (2pcs)
i:Screw (2pcs) j:Belt (1pc) k:Tip over restraints (1pc)
B
CRight changer side (1pc)
Left changer side (1pc) DChanger top bar (2pcs)
EChanger bottom bar (2pcs)
A
B
C
D
E
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE Do Not Use Power Drills or Drivers
D
E
14 pcs) 14 pcs)
16
2
m: 1/4”x4” Allen head bolt (2 pcs)
2pcs)
m4
EChanger bottom bar (4pcs)
E
E
1
1
2
2
1
2
2
4
2
n: 1/4”x2-3/8” Allen head bolt (2 pcs)
2
2-3/8
n
3/8”
e :

7
Metal spring support platform (1pc) Pad (1pc)
L
KM
FChanger shelf (1pcs)
The bottom bar(1pc)
GBack top rail (1pc) HBack bottom rail (1pc)
F
M
L
K
PBack right leg (1pc) QBack left leg (1pc)
GH
NFront rail (1pc)
N
GBack top rail (1pc) HBack bottom rail (1pc)
KLM
NPBack right leg (1pc) QBack left leg (1pc)
Changer shelf (2pcs)
1
F
1
1
F2
F2
F2
1
2

8
STEP 1
CRIB ASSEMBLY
STEP 2
2
B
D
D
E
e
e
e
e
c
c
c
c
c
c
c
c
P
1
E
1
E2
E2E2
E2
E1
E2
F1
F1
F2
F2
BD
D
E2
E1
E2
E2
E1
F1
D
F1
F2
F2
Use allen wrench(g) to connect bolts.
Connect changer longertop rail (D),
changer longermiddle rail 1(E1),
and changer longerbottom rail (E2)
to changer back leg (B1) and changer
front leg (B2) by using wood dowel (e1),
barrel nut (d) and 3”bolt (b).
e1
D
E1 E2

9
STEP 3
3
F
E
e
e
e
e
e
e
e
e
c
c
c
c
c
1
1
E2
F
2
F
2
c
D
D
C
c
CHANGER
To assemble part C to the assembled
part in Step 2 by using the same way
as step 1.
C
2
1

10
a
STEP 4
CRIB ASSEMBLY
H
b
b
a
a
a
a
a
a
ab
b
b
b
n
n
b
H
A
b
STEP 5
Attach Left head board (A)
to the back left leg (Q) using
Allen head bolt (n) and
barrel nuts (b).
Q
P
G
Q
G
P
To attach back bottom rail(H) and
back right leg(P) & back left leg(Q)
by using Allen head bolt (a).
To attach back top rail(G) and back
bottom rail(H) by using Allen head
bolt(a),(m).
5
m
m
4

11
STEP 6
Attach The left changer side (B)
to the back right leg (P) using bolts(d)
and allen wrench (g).
Model shown is example only.
Styles may vary .
6
P
H
A
B
d
d
d
P
STEP 7
Locate the mattress support (L)
with tabs.
Be sure the smooth side of the
mattress support (L) is faced upward.
Position the tabs of the mattress
support(L) to mount to the selected
position onto the legs.
Insert the bolts (f),through the
tabs and into thread inserts,
then tighten securely with allen
wrench (g).
L
L
HB
f
A
7

12
STEP 8
a
a
aa
b
a
c
H
AN
B
K
Attach the front rail (N) and the bottom
bar (K) to the left changer side (B) and
the left head board (A) using wood
dowels (c),bolts (a),barrel nuts (b)
and allen wrench (g).
b
b
b
8
Attach the front rail (N) and the bottom
bar (K) to the left changer side (B) and
the left head board (A) using wood
dowels (c),bolts (a),barrel nuts (b)
and allen wrench (g).

13
STEP 9
1.Assembly the Belt (j) to the changer side (B&C) using washer (h) and screw (i).
2.Add the pad (M) .
3.Put the child on the pad,then insert safty restrain system of the tape across child's waist.
The tightness can be adjusted by increasing the tension of the tape.
B
C
M
j
h
i
9
Note:
To ensure to assemble the shorter
belt to the side of crib, and the
longer one to the other side which
is farer from the crib.
longer belt
shorter belt

Converting crib to a toddler bed
！
Failure to follow these warning and the assembly instructions could result in serious injury or
death from entrapment or strangulation.DO NOT place bed near windows where cords
from blinds or drapes may strangle a child.DO NOT place items with a string,cord,or ribbon
around a child’s neck,such as a hood, strings or pacifier cords.DO NOT suspend strings
over a toddler bed for any reason.
WARNING FOR TODDLER BED USE
The mattress intended for use on the bed shall be a full-size crib mattress having the
dimensions of 51-5/8” (1310mm) in length and 27-1/4”(690mm) in width and thickness of
4” (100mm) or a greater thickness as specified by the manufacture.The minimum age of the
intended user shall not be less than 15 months and the maximum weight shall not be greater
than 50ibs(22.7kg).
14
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.
(toddler rail and converting bolts are sold separately)
K
K
A
A

15
=
（LIT ENFANT RAIL EST VENDU SEPAREMENT）
K
K
A
A

Converting crib to a full size bed I
Converting crib to a day bed
16
You have the option to convert crib to a day bed
1:Remove the front rail (N)
2:Install the mattress support (L)
in its lowest position.
Conversion kit is sold separately You have the option to convert
crib to a full size bed I
1:Use the front rail as the
footboard of full size bed I
(legs are not included and
sold separately. );
2:Use the back rail as the
headboard of full size bed I;
3:Connect the front rail and the
back rail to the kits ( legs, long
rails,and hardware ) which are
not included and sold separately.
a
c
K
A
K
A
B
N
b
(Hollywood bed frame sold separately)

17
Converting crib to a full size bed II
You have the option to convert crib to a full size bed II
1:Use the back rail as the headboard of full size bed.
3:Connect the assembled parts and headboard of full size bed to the kits ( legs, long rails,and
hardware ) which are not included and sold separately.
2:Connect the left foot platform and the right foot platform to the rail which are not included and
sold separately.
Converting kit is sold separately
PARTS REQUIRED TO COMPLETE STEP
LEFT FOOT PLATFORM
POST x 1
NOT INCLUDED
POST x 1
NOT INCLUDED
RIGHT FOOT PLATFORM POST x 1
NOT INCLUDED
RAIL
Model shown is example only.
Styles may vary .
(Hollywood bed frame sold separately)

FURNITURE TIPPING DETERRENT HARDWARE
18
Tipping furniture may injure young children. Use of this tipping restraint hardware is highly
recommended.
When properly instated this hardware could provide protection against the unexpected
tipping of furniture due to improper use.
WARNING
This hardware is only a deterrent.Adult supervision is the only proper deterrent to prevent
improper use of any potentially hazardous product.
1. Attach one of the mounting brackets securely to the back top edge of the furniture using
the short screw.
2. Find the stud in the wall and mark the location on the wall for mounting the second
bracket using a 2” wood screw approximately 2” below the bracket mounted to the edge
of the furniture.
3. If a stud cannot be found,purchase a “Hollow-Wall Anchor Bolt” and attach the second
bracket to the wall using that bolt.Make sure to follow all instructions by the manufacturer.
4. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
5. Lace an end of the nylon restraint strap down through each bracket.Bring both ends
together and slide the beaded end of the strap through the key hole shaped slot in the
other end tightly.Pull down on the beaded end until it snaps locks into the keyhole.
6. Check to make sure the strap is securely laced and locked to the brackets.
HOW TO LOCK

19

20
LIMITED WARRANTY
� Dream on Me warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
� This warranty covers 30 days from the date of original purchase.
� This warranty is valid only upon presentation of proof of purchase.
This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
� This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
� This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
WARNING: Should this product become damaged, and/or components
are broken or missing, DO NOT USE