FIBER FOX MINI100HA User manual

1
Operation Manual
MINI100HA & MINI60A
Video link & QR code
https://youtu.be/g3HF521zCTs

2
Table of Contents
I. Preparation_Splicer holder setting
II. How to attach MINI60A to MINI100HA
III. How to access Stripping / Splicing / Heating Mode
IV. How to operate Stripper
V. How to operate Cleaver
VI. How to operate Splicer
VII. How to operate Heater

I.
Preparation
- Default setting for Universal holder (Screw Fixed)
3
- Splicer
- Stripper
- Cleaver

I.
Preparation
- Default setting for detachable holder
4
-Cleaver -Stripper
- Splicer

-
Detachable holder (Basic kit in the
package)
Applicable for 250Um bare fiber
-
Detachable holder (Basic kit in the
package)
Applicable for 900Um tight buffered cable
-
Detachable holder (Optional)
Applicable for 2.0~3.0mm indoor cable
- Detachable holder (Optional)
Applicable for 900Um loose buffered cable
- Detachable holder (Optional)
Applicable for Rectangular Drop cable
- Screw Fixed type Universal holder (Optional)
Applicable for 250Um~3.0mm tight buffered cable
I. Preparation
- Holder set per cable type

II. How to attach MINI60A to MINI100HA
6
-Screw out a bolt in the blue circle.
-Loosen a bolt in the red circle. -Slide the tray all the way to the right
-Tightens the screw in the red circle to lock
-Put the other screw back in the hole
in the blue circle.

II. How to attach MINI60A to MINI100HA
7
-Place Mini60A over the tray.
-make sure the four spot rubber feet match
with the holes on the tray.
-The cleaver is securely attached with a
magnet plate.
-Slide a safety lock to the right to unlock
the cleaver

IV.
How to set Stripping / Splicing / Heating Mode
8
1. Turn on the machine
2. Click ‘Splice Mode’ and choose one.
2. Click ‘Strip Mode’ and choose one.
2. Click ‘Heater Mode’ and choose one.

IV.
How to operate Stripper
9
-
Green light = Good to go
** Fiber preparation refer to the left picture.
(Required stripping length : 2.5 ~ 3㎝)
-Press a button ’Strip’ for warm-up -Red light will be on : it means ‘warming up’
- Turns to Green : it means ‘warmed up’
Wait 20Sec.
2.5 to 3㎝

IV.
How to operate Stripper_with detachable holder
-Open the stripper covers
-Place the holder with fiber on the stripper -Close the left cover
(It helps the fiber keeps appropriate position)
- Stripping process is made automatically. -Close the right cover 10

IV.
How to operate Stripper
11
-After stripping process, open the left cover - Take the holder out
-Place the holder over the cleaver rail

IV. Stripper_Cleanning and re-positioning
12
-Open the right cover
-The left module automatically comes back
and it is ready for the next stripping.
-Please clean the plate with a brush
* the brush is in the package *

V.
How to operate Cleaver_with detachable holder
13
-Place the holder over the cleaver rail
* Magnetism between holder
and cleaver is guiding you
the appropriate fiber position
Magnetic bolts
-Press the cover then cleaving process is done
Magnetic
Plate

VI.
How to operate Splicer
14
on the right side of the splicer rail
for
the left rail.
-Place the holder with fiber
-After cleaving, take the holder out
-Repeat the same process

VI.
How to operate Splicer_with detachable holder
15
-When the both side fibers
are placed on the splicer,
-Close the cover - it automatically process the
splicing
• You can also set manual
to check and decide in
each step of the process

VII.
How to operate Heater
16
-After splicing,
prepare a protective sleeve
-Open the splicer cover
-Open the holder cover on both side

VII.
How to operate Heater
17
-Open the heater cover and take the
spliced fiber with the protection sleeve
positioned in the middle
-Put it into the heater and the heater
cover will be closed
-Press a button ‘Heat’, then it starts
heating process with red light on.
-Red light will be off when it is done.
-Take the fiber out and check.