Fiberfin PEW 9.1128 User manual

Rev.: 2013-06-02
1 / 5
Before starting any work, read these operating instructions!
Operating Instructions
Hand crimp tool PEW 9.1128
EN
Operating Instructions
Hand crimp tool PEW 9.1128 for HFBR-connectors
Art.-No. 619 1128 3 1

Operating Instructions
Hand crimp tool PEW 9.1128
Rev.: 2014-06-02
2 / 5
EN
Table of contents
1 General 3
2 Intended use 3
3 Description 3
4 Application / Crimping procedure 4
5 Emergency unlocking 4
6 Warranty 5
7 Service and maintenance 5

Operating Instructions
Hand crimp tool PEW 9.1128
Rev.: 2014-06-02
3 / 5
EN
1 General
Keep the Operating Instructions with the hand crimp tool at all times. This hand crimp tool
features state-of-the-art technology and complies with recognised safety regulations. The
crimp tool may be used only in a technally fault-free condition, in a safety-conscious manner
with consideration given to potential hazards, and may be used only for the purpose described
in the Operating Instructions.
The manufacturer is not liable for any damages that occur as a result of unauthorized
modifications made to the hand crimp tool or its improper use. Always isolate wires from the
power supply!
2 Intended use
· for crimping HFBR-connectors 2,2 mm POF
· Simplex or duplex versions: 4501/4511, 4503/4513 and 4506/4516
3 Description
The crimping tool utilizes a leverage mechanism. Once the last tooth is passed in the ratchet
(force operatin to complete), the crimping tool opens automatically. To prevent damage to the
crimping die or connector, the built-in emergency release lever (Do not use crimped terminals
that have not completed the cycle) enables the tool to be opened prematurely in the event of
failed crimping.
crimp position 2 for
HFBR 4501/4511
and 4503/4513
crimp position 1 for
HFBR 4506/4516
turnable positioner
(locator)
locking lever emergency
release lever
figure 1

Operating Instructions
Hand crimp tool PEW 9.1128
Rev.: 2014-06-02
4 / 5
EN
5 Emergency unlocking
The force lock opens automatically if the crimp procedure completes in full. In case the crimp
procedure needs to be interrupted, the force lock can be released with a suitable tool (e.g.
screwdriver). (figure 7)
4 Application / Crimping prodedure
· Open the tool
· Select the necessary positioner, lift it and turn it in the right position until it locks (figure 2)
· Insert the HFBR connector in the corresponding position (figure 3)
· To avoid turning the HFBR-connector close the tool until the connector is held tightly
· Lift the locking lever and turn until it clicks into place in the upper position (figure 4)
· Insert the prepared wire to the stop and hold tight (figure 5)
· Press the handles together until the compulsory lock is released and the connector has
been crimped
· Tool opens automatically, lift the locking lever and turn downwards, remove the crimped
connector (figure 6)
figure 2 figure 3 figure 4
figure 5 figure 6 figure 7

Operating Instructions
Hand crimp tool PEW 9.1128
Rev.: 2014-06-02
5 / 5
EN
6 Warranty
The hand crimp tool is subjected to a thorough quality control process.
General warranty conditions apply.
7 Service and maintenance
Before starting work, ensure that the hand crimp tool is clean and in proper working order.
Crimping residue must be removed. Joints should be regularly oiled with a light mineral oil and
protected against contamination. It must be ensured that all bolts are secured by means of
securing rings. As a rule, all repairs to the wire end ferrule crimping tool must be performed
by the tool manufacturer or an authorised service centre. Please contact the dealer where
you purchased your tool.