Field Controls PVG-100 User manual

www.eldcontrols.com
Please retain these instructions after installation.
This device MUST be installed by a qualied agency in accordance with the manufacturer's installation instructions. The denition of
a qualied agency is: any individual, rm, corporation or company which either in person or through a representative is engaged
in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the
precautions required, and has complied with all the requirements of the authority having jurisdiction.
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.
Installation Date:
Installed By: Phone:
POWER VENTER SYSTEM
Model: PVG-100, PVG-300, PVG-600
ITEMS INCLUDED:
1- PVG-100, 300, or 600 POWER VENTER with
pre-wired integral 24 VAC Relay/Timer, factory
set Draft Proving Switch, and direct access
Terminal Blocks.
1- Installation Instruction Sheet
OPTIONAL SYSTEM COMPONENTS:
(NOT INCLUDED)
Side Wall Vent Hood
Spill Switches
Barometric Draft Control
CONTENTS PAGE
System Operation................................................ 2
Power Venter Sizing............................................ 3, 4
Installation Safety Instructions............................ 4, 5
Installation of Power Venter................................ 5, 6
General Wiring Instructions............................... 7
Airow Adjustments............................................ 8
Adjusting Thermostat Anticipator....................... 8
General Installation Inspection.......................... 8
System Control Check Procedures..................... 9
Troubleshooting Tips........................................... 9
Maintenance........................................................ 9
Replacement Parts List......................................... 10
Multiple Venting Systems.................................... 10, 11
Venting System Operational Information.......... 11
Included is one ETL LISTED power venter to be used for side wall venting of a single 24 VAC controlled
furnace, boiler, or water heater which burns natural or LP gas. The PVG may also be used to vent a single
24 VAC controlled gas red furnace or boiler and a 30 millivolt residential gas red water heater.
P/N 46246300 Rev M 04/20

page 2 of 12
SYSTEM OPERATION
1. The thermostat (wall thermostat, or aquastat) calls for heat and energizes a relay which activates the
power venter. After the venter motor has come up to speed, the pressure switch closes. This completes the
circuit to the burner and allows the burner to re.
2. For millivolt controlled water heaters, the gas pressure switch on the gas valve activates the power venter
at the same time as the burner res.
3. After the heating requirement has been satised, the thermostat circuit will open and de-activate the
burner and power venter circuit.
4. The post purge timer continues to run the power venter for a period of time after the burner has shut o to
purge remaining ue gases.
UNIT SPECIFICATIONS
Table 1
UNIT DIMENSIONS (INCHES) ELECTRICAL RATINGS
MODEL H W D I/O* VAC Hz RPM WATT AMP TP**
PVG-100 7.5 10.0 7.0 4⁄4115 60 3000 145 2.1 YES
PVG-300 7.5 11.5 7.0 4⁄4115 60 3000 145 2.1 YES
PVG-600 8.75 12.0 8.5 5⁄5115 60 3000 167 1.5 YES
*Inlet and outlet diameter
**Thermally protected motor
SIDEWALL VENT HOODS (Model SWH-1)
Sidewall vent hoods are available in the following sizes. The vent hood should be chosen that matches the
outlet size of the Power Venter. (See Figure 2) NOTE: When using dierent sizes, consider reducers and
specic size pipe when determining equivalent length of vent pipe.
Figure 1
SWH-1-3 - 3"
SWH-1-4 - 4"
SWH-1-5 - 5"
SWH-1-6 - 6"
SWH-1-8 - 8"
Figure 2
P/N 46246300 Rev M 04/20

page 3 of 12
POWER VENTER SIZING
In order to choose the correct size power venter for a particular installation, the total input ring rate and
total equivalent length of vent pipe to be used must be known. Refer to Table 2 to determine the maximum
allowable equivalent feet of pipe for each model used with the pipe diameters shown. When venting
multiple appliances, add the input of each appliance to determine the total input. Always choose a power
venter that is capable of handling more than the system requires. The choke plate can be adjusted to
compensate for the dierence.
MAXIMUM EQUIVALENT HORIZONTAL PIPE LENGTH (FEET)
BTU/HR INPUT
VENTER MODEL NUMBER AND VENT PIPE DIAMETER
PVG-100 PVG-300 PVG-600
3" 4" 4" 5" 6" 5" 6" 8"
25,000 270 455 -- -- -- -- -- --
55,000 100 169 -- -- -- -- -- --
70,000 -- 144 -- -- -- -- -- --
100,000 -- 100 305 -- -- -- -- --
145,000 -- -- 145 247 334 413 -- --
220,000 -- -- 64 100 147 181 -- --
310,000 -- -- -- 54 74 91 146 216
400,000 -- -- -- -- -- 54 87 134
520,000 -- -- -- -- -- -- 52 86
610,000 -- -- -- -- -- -- -- 66
Table 2
PROCEDURE FOR CALCULATING TOTAL EQUIVALENT PIPE LENGTH IN FEET
1. Calculate the total equivalent feet for each type of tting used in the venting system from the following chart.
2. Calculate the total amount of feet for the straight lengths of vent pipe.
3. Add the equivalent feet for the ttings with the total amount of feet of straight lengths.
Table 3
*Reducer or increaser ratio (d/D) small diameter divided by the larger diameter. (See Figure 3)
Example: 4" to 8" reducer, the reducer ratio is d/D = 4⁄8= 1⁄2. To estimate the
equivalent foot length for the tting, use the smaller pipe diameter for the equivalent
length gure. Example: 4" to 8" reducer; the reducer ratio is 1⁄2and the smaller pipe
diameter is 4". So, from the chart, the equivalent feet would be 7 feet.
Example: System Pipe Size = 4"
Step 1 2 – 90° Elbows (4") = 14 Ft.
Step 2 10 - 2 Ft. Lengths of 4" Pipe = 20 Ft.
Step 3 Total Equivalent Feet = 14 Ft. + 20 Ft. = 34 Ft.
Figure 3
EQUIVALENT LENGTH (FEET) OF VENT PIPE FOR VENT PIPE FITTINGS
VENT PIPE FITTINGS VENT PIPE DIAMETER
3" 4" 5" 6" 7" 8" 9" 10"
TEE 1925313844505663
90° ELBOW 5 7 9 11 12 14 16 18
45°ELBOW 34456789
REDUCER
(d/D)*
1⁄48 11141719222528
1⁄25 7 8 1012131517
3⁄423344566
P/N 46246300 Rev M 04/20

page 4 of 12
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This device must be installed by a qualied installer in accordance with the manufacturer's installation
instructions. Appliances should have a minimum of 75% combustion eciency or have a maximum measured ue
gas temperature of 550°F at the inlet of the venter.
1. The power venting system must be installed by a qualied installer. "Qualied Installer" shall mean an
individual who has been properly trained or a licensed installer. The installer must write or imprint his name,
phone number and date of installation on the installation tag. The tag should be attached to the power venter
unit. Recording burner and venting system initial operational information is recommended as a guide for
service or burner tune-up. Enter this in the space provided in this manual.
2. Safety inspection of a venting system should be performed before and after installing a power venting system
on an existing or new appliance. Procedures to follow are those recommended by the National Fuel Gas Code,
ANSI Z223.1 or refer to the "General Installation Inspection" section of this manual.
3. Plan the vent system layout before installation to avoid the possibility of accidental contact with concealed
wiring or plumbing inside walls.
4. Single wall vent pipe may be used to join an appliance to the venting system, but if proper clearances cannot
be maintained from combustible materials, Class B Vent Pipe should be used for gas appliances. Refer to
national or local codes for guidelines.
5. Disconnect power supply before making wiring connections to prevent electrical shock and equipment
damage.
6. This equipment is designed to overcome minor negative pressure conditions. To ensure extreme negative
pressure does not exist, follow the "General Installation Inspection" section of this manual.
7. Heating appliances equipped with draft hoods, such as boilers or furnaces, LP and natural gas appliances
SHOULD have a secondary spillage switch installed. On appliances without draft hoods, it is recommended
that the secondary safety switch GSK-3 be installed into the system. Gas-red 30 millivolt power systems
MUST be equipped with a spillage switch.
Diagram A
P/N 46246300 Rev M 04/20

page 5 of 12
SIDEWALL VENT HOOD INSTALLATION
1. Use the inside wall plate as a template to mark
the hole location. Cut a hole 1" larger than
the marked hole to facilitate easy installation
(See Figure 4)
2. Center vent hood through the hole from outside.
Fasten the vent hood to the outside wall with the
appropriate type of mounting screws.
3. Fasten the wall end plate to the inside wall with
the appropriate type of mounting screws. NOTE:
Apply sealant to the outside mounting plate of
the vent hood to prevent leakage.
4. Connect the venter outlet or a properly sized section of vent pipe onto the inner pipe of the vent hood. Fasten
the connection with three sheet metal screws or equivalent fastening method.
5. Seal the vent hood inlet connection and any other vent pipe joints on the outlet side of the venter with an
approved high temperature silicone adhesive sealant or equivalent material.
INSTALLATION OF POWER VENTER
CAUTION: Failure to install, maintain and/or operate the power venting system in accordance with manufacturer's
instructions will result in conditions which may produce bodily injury and/or property damage.
1. Remove power venter from box and inspect unit for damage. If the carton has been crushed or mutilated,
check unit very carefully for damage. Rotate venter wheel to ensure that the motor and venter wheel
rotate freely. DO NOT install if any damage is apparent. Refer to unit sizing chart to check proper venting
sizing.
2. Location of the termination of the venting system should be installed in accordance with the National Fuel
Gas Code, ANSI Z233.1, manufacturer's recommendations, and/or local codes which are applicable. See the
following requirements or refer to Diagram A for typical locations.
a. The exit termination of mechanical draft systems shall not be less than 7' above grade when located
adjacent to public walkways.
b. A venting system shall terminate at least 3' above any forced air inlet located within 10'.
c. The venting system of other than a direct vent appliance shall terminate at least 4' below, 4'
horizontally from, or 1' above any door, window, or gravity air inlet into the building.
d. The vent termination of a direct vent appliance with an input of 50,000 BTU/HR or less, shall be
located at least 9" from any opening through which vented gases could enter the building. With an
input over 50,000 BTU/HR, a 12" termination clearance shall be required.
e. The vent termination point shall not be installed closer than 3' from an inside corner of an
L-shaped structure.
f. The vent termination should not be mounted directly above or within 3' horizontally from an oil tank
vent or gas meter.
g. The bottom of the vent terminal shall be located at least 12" above nished grade.
8. Air ow adjustment MUST be made to ensure appliance eciency. This should be done at the appliance
exhaust outlet with a velocity meter, draft gauge or by the “match test procedure”. The match test is in
accordance with National Fuel Gas Code A.N.S.I.Z223.1, Section 8.6.
9. On heating appliances not equipped with a draft hood, a barometric draft control MUST be installed to
regulate proper air ow and uctuations in the system’s air ow during operation. Fluctuations can come
from wind loads on the outlet of the venter, house depressurization during windy days, and the dierent
house ventilation requirements between summer and winter operation. Use a Field Controls Type MG-1
Barometric Draft Control. Gas-red draft induced systems should have a single-acting or double-acting
barometric draft control installed.
Figure 4
P/N 46246300 Rev M 04/20
NOTE: If mounting the power venter through a combustable wall material, a minimum clearance of 1/2”
must be maintained between the venter outerpipe and combustible materials.

page 6 of 12
VENTER LOCATION
Install the power venter onto the vent hood inlet or as close
to the vent hood inlet as possible. Always install the venter
such that the motor shaft is horizontal and the pressure switch
diaphragm is vertical. (See Figure 5) When venting a draft
induced gas red heating appliance a barometric draft control
must be installed on the vent system between the appliance
outlet and the venter inlet. (See Figure 6)
CAUTION: The power venter should never be installed
with the motor shaft in the vertical position. This could
allow heat to be trapped in the venter housing and radiate
through the motor possibly causing motor deterioration
and premature failure. Never attach the venter inlet directly
to the outlet of the heating appliance. Also, a minimum of
6" clearance between the venter housing and combustible
materials must be maintained.
CONNECTING VENTER TO THE FLUE PIPE
NOTE: The power venter should be supported in accordance with National Fuel Gas Code Z223.1, Section 7.910
as follows: A vent connector shall be supported for the design and weight of the material employed to maintain
clearances and to prevent physical damage and separation of joints.
NOTE: For gas red heating appliances not equipped with a draft hood, a barometric draft control must be installed
between the heating appliance exhaust outlet and the power venter inlet to regulate any draft uctuations during
operation.
1. Use approved vent connectors to join the heating appliance outlet to the venter inlet securing each joint with
sheet metal screws or equivalent means of fastening when required.
2. Seal all pipe joints on the outlet side of the venter with a high temperature silicone adhesive or equivalent. Test
the vent connections for leaks by using a soap solution as recommended by the National Fuel Gas Code, ANSI
Z223.1, Section 4.1.1.
NOTE: Do not enclose the space between the plates on the
outside of the vent hood or between the inner and outer pipe of
the vent hood. This might cause overheating of the wall structure.
Local codes might require fencing around the vent hood outlet.
Figure 5
Figure 6
Figure 7
OPTIONAL GSK-3 EXHAUST GAS SPILLAGE DETECTOR
SWITCH INSTALLATION
NOTE: Installation of the GSK-3 secondary safety switch is recommended
for LP and natural gas red appliances with a draft hood. This switch
will detect exhaust gas spillage out of the draft hood due to a blocked
vent system and/or inadequate draft during operation. When this switch
senses spillage it interrupts the power supply to the gas valve which
terminates the burner operation.
1. Mount the GSK-3 on the lower edge of the draft hood with
the exposed thermal disk directed into the draft hood.
(See Figure 7)
2. Route the electrical wires along the heating appliance cabinet
within an accepted wiring enclosure in accordance with the
National Electrical Code and any applicable local codes. Keep the wires away from any HOT surfaces.
P/N 46246300 Rev M 04/20

page 7 of 12
GENERAL WIRING INSTRUCTIONS
CAUTION: Disconnect electrical power before wiring power venter!
Connect line voltage (110/120 VAC) through junction box access hole labeled 120 VAC ONLY. Connect low voltage
control wiring through junction box access hole labeled 24 VAC CONTROL WIRING ONLY. VENTER MUST BE GROUNDED!
Check ground circuit to make certain that venter has been properly grounded. The wiring must be protected by
an over current protection circuit such as a fuse or circuit breaker rated at 15 amperes. Prevent wiring contact with
any heat source. Wire the venter in accordance with the National Electrical Code and applicable local codes. Refer to
Diagram B for proper wiring specications.
Diagram B
3. Wire the switch into the low voltage thermostat circuit. Refer to the appropriate wiring diagram in this manual.
4. After installation, check the amperage through the thermostat circuit and adjust the anticipator if necessary.
CAUTION: The GSK-3 is a manual reset switch. Investigate the system thoroughly for the cause of any shut down and
correct the problem before resetting the GSK-3 and restarting the system.
P/N 46246300 Rev M 04/20

page 8 of 12
ADJUSTING THERMOSTAT ANTICIPATOR
If connecting the Power Venter system to a gas appliance with a thermostat
anticipator, refer to the following to make adjustments. Disconnect one
side of the thermostat circuit at the gas valve or burner control, and
connect an ampere meter into the circuit. With the system running, take
an amperage reading on the circuit. Check the nameplate or instructions
for the thermostat to obtain the proper amperage level. Adjust amperage
level by moving the anticipator lever. Reconnect the thermostat to the
gas valve and start the system operating. Time the burn cycles and
adjust as follows; To make the cycle time longer, increase the amount on
the anticipator (Example: .45 to .5 Amps); to decrease cycle time, reduce
the amount on the anticipator (Example: .45 to .3 Amps). (See Figure 8)
AIR FLOW ADJUSTMENTS
1. To properly adjust the venter air ow, loosen the inlet ring screws and
open the choke plate approximately 1⁄2to 3⁄4open. (See Figure 10) Start the
heating appliance following the manufacturer specied procedure, and
set the thermostat to call for heat.
2. After the system has operated for several minutes to stabilize the exhaust
gas temperature, check for air ow at the draft hood or the heating
appliance outlet using a velocity meter, draft meter, or match test
procedure.
3. Adjusttheventerchokeplateinwardoroutwardtoobtaintheminimumdraft
necessarytomaintainventing.Thenincreasethedraftslightly(approximately
10%overminimumowrate)toensureproperventingduringanyvariations
in venter performance, such as wind load or house depressurization.
4. Secure the choke plate into position by tightening the screws on the
inlet collar (See Figure 9)
GENERAL INSTALLATION INSPECTION
Follow recommended procedures for safety inspection of a heating appliance in accordance with the National Fuel
Gas Code ANSI Z223.1. The following procedure will help in evaluation of the venting system. It is intended as a
guide to aid in determining that the appliance is properly installed and is in a safe condition for continuous use.
This is a generalized procedure which cannot anticipate all situations. Accordingly, in some cases deviation from
this procedure may be necessary to determine safe operation of the equipment. If it is determined that a condition
which could result in unsafe operation exists, the appliance should be shut o and the owner advised of the unsafe
conditions. Corrections must be made prior to allowing continuous operation. The following steps should be taken
in making a safety inspection.
1. Visually inspect the venting system for proper size and determine that there is no blockage, restriction, leakage,
corrosion, or other deciencies which could cause unsafe operation.
2. To the extent possible, close all building doors, windows, and all doors to the room in which the heating
appliance is located. Turn on clothes dryers and any exhaust fans so that they operate at maximum speed. Do
not operate a summer exhaust fan. Also close all replace dampers. If after completing steps 3 through 7 it is
believed that sucient combustion air is not available, refer to the National Fuel Gas Code ANSI Z223.1 or any
local codes for proper guidelines.
3. Place the appliance being inspected into operation. Follow the lighting instructions and adjust the thermostat
so that the heating appliance will operate continuously.
4. Determine that the burner is operating properly and that the main burner ignition functions satisfactorily, by
interrupting the electrical power of the appliance in any safely convenient manner. Test the burner safety device
to determine if it is operating properly by extinguishing the pilot or disconnecting the ame safety circuit.
Figure 8
Figure 9
P/N 46246300 Rev M 04/20

page 9 of 12
SYSTEM CONTROL CHECK PROCEDURES
1. Adjust the thermostat to call for heat and observe the power venting system for proper operation sequence.
Repeat as necessary.
a. Thermostat calls for heat.
b. Venter relay is energized which starts venter motor.
c. Pressure switch closes which allows burner to re.
d. Thermostat is satised, burner stops operation.
e. Venter continues to operate for up to 2 minutes during the post purge cycle.
2. While the system is in operation, disconnect the draft tube from the air pressure switch. The pressure switch
should open and interrupt burner operation. Re-connect the draft tube to the air pressure switch which should
allow the burner to re-light.
3. If a GSK-3 secondary safety switch is installed, allow the vent pipe to cool and disconnect the vent pipe between
the appliance outlet and venter inlet. Block the vent connected to the appliance with a non-combustible
material. Activate the heating system main burner and verify that the GSK-3 shuts down the burner within a
few minutes or less. Reset the GSK-3 and repeat.
TROUBLESHOOTING TIPS
1. Burner does not re when thermostat calls for heat.
a. Make sure draft tube is securely fastened to the air pressure switch, and is not blocked.
b. Check for continuity across pressure switch terminals when venter is operating.
c. Check wiring connections between air pressure switch and appliance.
2. Venter does not activate when thermostat calls for heat.
a. Check to see if relay closes when thermostat calls for heat.
b. Check wiring connections.
c. Check motor for unrestricted shaft rotation.
3. Exhaust gas odor.
a. Check system draft level during operation.
b. Check vent system on outlet side of venter for leakage.
c. Check for negative pressure in building.
MAINTENANCE
Motor: Inspect the motor once a year - motor should rotate freely. To prolong the life of the PVG-600 motor, it must
be lubricated with six drops of SWG Superlube, Part #46226200, annually. The PVG-100 and PVG-300 have sealed
ball bearings, and therefore do not need to be oiled.
Blower Wheel: Inspect the blower wheel annually to clear any soot, ash or coating which inhibits either rotation or
air ow. Remove all foreign materials before operating.
Vent System: Inspect all vent connections annually for looseness, for evidence of corrosion, and for ue gas leakage.
Replace, seal, or tighten pipe connections if necessary. Check the power venter choke plate to ensure it is secured
in place. Check the barometric draft control, if installed, to ensure the gate swings freely.
System Safety Devices: With the heating system operating, disconnect the pressure sensing tube from the pressure
switch on the venter. This should stop the burner operation. Re-connecting the tube will relight the burner. For 30
millivolt operating systems, disconnect one lead of the spill switch circuit from the thermocouple junction block.
This should shut o the pilot and the burner. Re-connection will allow re-lighting of the pilot.
5. Visually determine that the main burner is burning properly, i.e. no oating, lifting, or ashbacks. Adjust the
primary air shutter as required by the appliance manufacturer. If the appliance is equipped with high and low
ame control or ame modulation, check for proper main burner operation at both ame levels.
6. Test for exhaust gas spillage at the draft hood or the barometric draft control after approximately 5 minutes of
main burner operation. Use a draft meter or ame or smoke from match, candle or cigarette.
7. Turn on all fuel burning appliances within the same room so that they operate at their maximum capacity. Then
repeat Steps 5 and 6.
8. Return all doors, windows, exhaust fans, replace dampers, and any other fuel burning appliances to their
previous condition.
P/N 46246300 Rev M 04/20

page 10 of 12
MULTIPLE VENTING SYSTEMS
1. To vent a 24 VAC controlled boiler or furnace and a
30 millivolt residential water heater using one PVG
power venter refer to the following.
a. Follow the instructions for safe and proper
venting previously specied in this manual.
Make sure that the combined gross BTU/HR
input and equivalent vent pipe length does not
exceed the maximum venting capacity of the
venter selected.
b. A CK-20FV or CK-20FG control kit MUST be
added to the system to properly control the
venter during operation of the water heater.
Refer to Figure 10 and Diagrams C and D for
vent pipe arrangement and wiring information.
2. To vent two 24 VAC appliances using one PVG
power venter refer to the following.
a. Follow the instructions for safe and
proper venting previously specied in
this manual. Make sure that the combined
gross BTU/HR input and equivalent vent pipe length does not exceed the maximum venting capacity of
the venter selected.
b. A CK-41 Control Kit must be added to the system to properly control the venter when common venting an
additional 24 VAC furnace or boiler. Tee the draft tube on the PVG unit to connect to the air pressure switch
on the Control Kit. Refer to Diagram D for wiring instructions.
PV SERIES POWER VENTER: VERTICAL VENTING OPTION
Diagram C illustrates correct and incorrect installation of PV series venter in vertical vent conguration (except
PVE-1200). The correct installation maintains the required vertical position of the pressure switch; the incorrect
installation does not. The following conditions must also be observed:
•Natural gas, LP gas or #2 fuel oil appliance rated at 75% or greater non-condensing type of appliance
•Maximum input temperature at power venter: 575°F
Figure 10
REPLACEMENT PARTS LIST
The following items are available for replacement, if necessary.
REPLACEMENT PARTS LIST
DESCRIPTION PVG-100 PVG-300 PVG-600
Motor 46032000 46032000 46083300
Blower Wheel 46080100 46033400 46089400
24 VAC Relay 46282800 46282800 46282800
Pressure Switch 602602001 602602002 602602003
P/N 46246300 Rev M 04/20

page 11 of 12
Diagram D
LNM T1T
RELAY/TIMER
N/OCOM
PLASTIC
BUSHING
AIR PRESSURE SWITCH
PVG JUNCTION BOX
MOTOR
LEADS
13
2T3
LNM T1T
RELAY/TIMER
N/OCOM
PLASTIC
BUSHING
AIR PRESSURE SWITCH
PVG JUNCTION BOX
MOTOR
LEADS
13
2T3
APPLIANCE
CONNECTIONS
L1 N M T1 T2 T3
APPLIANCE
CONNECTIONS
L1
L2
TERMINAL STRIP IN 24VAC
CONTROL KIT ON SECOND APPLIANCE
APPLIANCE
CONNECTIONS
L1
L2
GAS PRESSURE SWITCH
ON MILLIVOLT APPLIANCE
PVG WIRING FOR MULTIPLE 24VAC APPLIANCES PVG WIRING FOR MULTIPLE 24VAC APPLIANCES
VENTING SYSTEM OPERATIONAL INFORMATION
Date:
Heating appliance BTU/HR input
Gas valve operation pressure
Vent system draft above draft hood or below
barometric draft control
CO2measurement
CO measurement
Appliance outlet ue gas temperature
P/N 46246300 Rev M 04/20
Diagram C

Phone: [phone] • Fax: [phone]
www.fieldcontrols.com
© Field Controls, LLC P/N 46246300 Rev M 04/20
This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)
This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)
WARRANTY
WARRANTY
For warranty information about this or any Field Controls product, visit:
For warranty information about this or any Field Controls product, visit:
www.eldcontrols.com/ventCool
www.eldcontrols.com/ventCool
Field Controls Technical Support
Field Controls Technical Support
1.800.742.8368
1.800.742.8368
eldtec@eldcontrols.com
eldtec@eldcontrols.com
This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)
This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)
WARRANTY
WARRANTY
For warranty information about this or any Field Controls product, visit:
For warranty information about this or any Field Controls product, visit:
www.eldcontrols.com
www.eldcontrols.com
Field Controls Technical Support
Field Controls Technical Support
1.800.742.8368
1.800.742.8368
eldtec@eldcontrols.com
eldtec@eldcontrols.com