Fiil T1 User manual

4
Main User Interfaces
9
6Charging Case Cover
Left earphone (slave)
Right earphone(master)
7L
7R
L
Earphones
Charging Case
1Earwing
LED indicator
Eartip
2
3
Left earphone (slave) RRight earphone (master)
6
7L
7R
8L
8R
9
Charge indicator(slave)
Charge indicator(master)
Micro USB connector
8L
8R
1
3
2
5
4R
1
3
2
4L
4L Touch control(slave)
Touch control (master)
Microphone
4R
5
TRUE WIRELESS EARPHONES
USER MANUAL

5 6
Get Started
STEP1
Put earphones into charging
case and close the cover.
STEP2
Open the charging case then
earphones will automatically get
sync and enter pairing mode.
*Notes :
Please charge the charging case via USB adapter in advance.
Enter setup menu of audio source devices, select “search device” in
“Bluetooth” then select “FIIL T1” in the device list to connect.
Search Connection
Bluetooth Pairing
Bluetooth pairing
For 󽗉rst usage of brand new FIIL T1, please refer to page5 “Get Started”,
the earphone status indicator will continue to blink blue once entered
pairing mode.
To begin a new bluetooth pairing, please press and hold the master
earphone (right earphone) until the LED indicator blinks blue.
< Settings
Bluetooth
Bluetooth
My Device
FIIL T1 Connceted
FIIL Diva2 Disconnceted
FIIL Driifter Disconnceted

7 8
How to Control
1x
+2sec
1x 2x 3x
Next track Previous
track
End CallAnswer Call
Play/Pause Voice
assistant
Reject Call
Play/Pause Vol + Vol-
Left earphone
(slave)
Right earphone
(master)
Bluetooth Sync
Manual Sync
Auto-Sync
Please refer to page5 “Get Started”, the left and right earphones will
automatically get synced after Step2.
1st Step
Place the earphones into charging case ,
press and hold both earphones untill power
o󽗈 (LED indicates red then o󽗈).
2nd Step
Press and hold both earphones again
untill their LED indications light purple.
3rd Step
Close charging case then open again, the
earphones will automatically get synced
with 󽗊ashing purple LED.
Left earphone
(slave)
Right earphone
(master)
User Interface

9 10
When charging case is not able to charge
earphone or its LED indicator blinks red,
it means battery low and charging case
shoule be recharged.
How to charge
When both red LED indicators are light
on, it means the charging case is being
charged.
When both red LED indicators are light
o󽗈, it means the charging case and
earphones are fully charged.
How to charge
Charge earphone
When earphone reminds “recharge
headset” or the LED indicator blinks red
, that means battery is low and earphone
should be charged.
Place the earphone into charging case and
close, then earphone will be charged.
*Notes: Earphone will power o󽗈 during charging, so the left earphone
(slave) can not be singly used if right earphone is being charged.
Charging Case indicator
When the red LED indicator (left or right) is
on, it means the corresponding earphone is
being charged .
When the red LED indicator is o󽗈, it means
the corresponding earphone is fully charged .
Charging Case indicator
Recharge Charging Case
Please open USB door at rear side of charging
case, connect Micro USB cable with USB
adapter to recharge charging case.

FCC Statement
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirment.
The device can be used in portable exposure condition without restriction.