Fiilex C360 Series User manual

User Manual
FLXC360 FLXC365
C360 Series
190103A2

1
Mode
Manual Red/Green
Directly adjust the light’s output via the control knobs. Press
the On/Off Button to toggle the fixture’s output on and off.
Red: Light output off - Settings are still adjustable
Green: Light output on
Control via DMX. Manual control knobs become disabled.
DMX Mode activates automatically when a signal is detected.
Orange
DMX
Description
On/Off
Button Color
General Notes
• The C360 Series has been designed for professional studio and location applications and may only
be operated by qualified persons.
• Please read the following operating instructions very carefully before using this fixture.
• For your own safety, please follow all safety instructions and warnings.
• Keep these operating instructions for future reference.
• For further information, contact Fiilex ([email protected]) or your retailer.
Basic Operation (refer to Parts Diagram on following page)
• Mounting
The C360 Series can be installed with desired hanging/mounting hardware and can be hung
onto secured rigs.
• Powering On
The C360 Series comes with its own integrated Power Module Box (8). To supply a C360
Series fixture with power, plug the power cord into a power outlet. The fixture’s OLED
Display (19) will turn on once it is receiving power. The On/Off Button (15) can toggle the
fixture’s output on and off. Settings can still be adjusted while the switch is set to off.
• Adjusting the Settings
Use the Yoke Knobs (2) to lock the fixture’s tilt position. Tighten the handle to secure.
• DMX Interface
Both fixtures are also DMX512 compatible through RJ45 ports, allowing users to operate them
remotely via the Fiilex DMX Controller or any standard DMX board.

Parts Diagram
Compatible Accessories
2
Size IV Barndoor
Powering On
Press the On/Off
button to turn on the
light. The button will
turn green to indicate
that the light is on.
Plugging In
Plug the Power Cord
into a power outlet.
Mounting the Light
Use the size M12
screw receiver on the
C-Series yoke to
attach the fixture to
the desired hanging/
mounting hardware.
Adjusting the Settings
Turn the knobs to
adjust CCT, Hue and
Intensity.
1. Barndoor Brackets
2. Yoke Knob
3. Barndoor Lock
4. Magnetic Accessory Lock
5. Side Vents
6. Size M12 Screw Receiver
7. Power Cord
8. Power Module Box
9. 5” Fresnel Zoom Lens (C365 only)
10. Lens Tighten Knobs (C365 only)
11. Barndoor Brackets (C365 only)
12. Barndoor Lock (C365 only)
13. Light Intensity / DMX Address Knob
14. Rear Vents
15. On / Off Button
16. CCT / Hue Tuning Knob
17. Yoke
18. Barndoor Lock Release
19. OLED Display
20. RJ45 In / Out
13
16
15
DMX Controller
SnootLouverHoneycomb N Honeycomb W Dome DiffuserFresnel Lens
7
1
9
4
2
3
10
12
11
13
1415
16
17
18 19 20
5
6
7
8

Rear Panel Interface Operation
3
Assigning DMX Address:
DMX Address Setting Screen
Dial
CCT
PWR
HUE
DMX
Range
2800K - 6500K
100% - 0.1%
±0.25 Green
1 - 510
Function
Set color temperature
Set intensity
Set hue value
Set DMX address
%
D
PWR HUE
DMX
CCT
1. Double click the Light Intensity / DMX Address Knob (13) to
unlock DMX address setting screen on the OLED Display (19).
2. Rotate the knob to select desired base address (1-510).
3. Lock in setting by clicking knob once. Alternatively, the address
will automatically lock in after 1 second of inactivity.
4. The C360 Series fixtures occupy three consecutive DMX channels for operation. For example,
with a base DMX address of 50, the controls for intensity, CCT, and hue will correspond to DMX
channels 50, 51, and 52 respectively.
Specifications
CCT Range
Light Engine
Power Draw
DC Input
AC Input
DMX Ports
Weight (With Power Cable)
Mounting Hole Diameter
Thermal Design
Operating Temperature
IP Rating
LED Lifetime
Certifications
2800 - 6500K Continuous Tuning
Dense Matrix LED
85W Max
N/A
120V AC, 60Hz
RJ45 (In & Out)
C360: 3.4lbs / 1.5kg | C365: 4.4lbs / 2.0kg
C360: 8.2in x 4.7in x 5.6in / 20.8cm x 11.9cm x 14.2cm
C365: 8.2in x 7.5in x 6.4in / 20.8cm x 19.1cm x 16.3cm
0.5in
Advanced Vapor Cooling System (Fan Cooled)
32 - 104ºF / 0 - 40ºC
IP-20
42,000 hours
CE, UL, FCC
• To adjust the fixture’s DMX address via RDM, consult operating instructions for DMX/RDM control systems.
Size (L x W x H)

4
Warranty
Unless otherwise stated, your product is covered by a one year parts and labor limited warranty.
Fiilex guarantees, to the original buyer, that this product is to be free of defects in both workman-
ship and material for a period of one year from the date of shipment. This warranty extends to all
products which have proved defective through normal use but excludes products that have been
disassembled, modified or misused by the buyer or any other person. This warranty is in lieu of all
other warranties, and disclaims all warranties expressed or implied, including any warranty of mer-
chantability, fitness for a particular purpose, or arising from the course of dealing between the
parties or usage of trade.
Returning an Item Under Warranty for Repair
It is necessary to obtain a Return Authorization Number (RA#) from your dealer/point of purchase
BEFORE any units are returned for repair. Fiilex will make the final determination as to whether or
not the unit is covered by warranty. Fiilex will replace or repair to proper working condition any
products that are returned under warranty. Products repaired or replaced under warranty are
under warranty only for the remaining unexpired period of time of the original warranty.
Any Product unit or part returned to Fiilex must be packaged in a suitable manner to ensure the
protection of such Product unit or parts. The package must be clearly and prominently marked to
indicate that the package contains returned product units or parts with a Return Authorization
(RA#) number. All returned product units or parts must be accompanied by a written explanation of
the alleged problem or malfunction.
1689 Regatta Blvd. Richmond, CA 94804
| [phone] | fiil e[email protected]
www.fiilex.com
Safety
• Do NOT attempt to disassemble the body of the C360 Series. Doing so will void the warranty.
• Do NOT submerge the C360 Series Fixtures in water.
• Do NOT cover/block the side and back air vents.
• Use only a soft, dry towel to gently clean the exterior of the light.
• Do NOT lift or suspend the light by the power cable.
• Do NOT use the C360 Series or accessories if they display any physical damage.
• Before first use, make sure to remove all protective membranes.
• Make sure to adhere to local building codes when designing and installing the C360 Series
lighting systems.
• Do not install any luminaire assembly closer than 6 inches from any curtain, or similar
combustible material.