Filmcity FC-02 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Camera Cage Shoulder Kit (FC-02)
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Ass e mb l y M a n u a l
Mae Box MB-600 French and Side Flags
Front Handle Set Top Handle
9” Cage Brackets
Accessories
300mm Rod with Juncon
Adapters
Shoulder Pad
Straight &
Z Brackets
Accessory
Mounng Plate
Counter
Weight
Camera Base with
Quick Release
2x 300mm Female
threaded Rods
2x 300mm Male
threaded Rods
2x 200mm Female
threaded Rods
2x 150mm Male
threaded Rods
2x 100mm Male
threaded Rods
16:9 Mask

2
 Insert French Flag into Mae Box and ghten
the screws. In the same way, insert Side
Flags into (big) slots provided and secure
with the screws.
 Then aach Knicker on Conversion Ring.
NOTE: If the French Flag remains loose even
aer ghtening the knob, then slightly
ghten the allen bolt as shown.
MB-600 Mae Box Setup
 Insert 300mm Female threaded Rods into
Camera Base with Quick Release. Tighten
bolts with the help of provided allen key to
secure them properly.
 Fix the Quick Release of your uid head to the
boom of Camera Base and ghten bolts with
screw driver.
 Now mount it on uid head and secure
properly by ghtening the knob.
Shoulder Kit Setup

3
 Loosen Ratchet Knob and remove Quick
Release Plate by pressing the Quick Release
Pin.
Quick Release
Pin Ratchet
Knob
 Fix the quick release plate with camera and
ghten bolts using screw driver.
 Now mount camera with Quick Release Plate
on the Camera Base and ghten knob
properly to secure it.
 Aach both Cage Brackets with rods and
ghten the knobs to secure them
appropriately.
 Insert 2x 200mm female threaded rods into
Cage Brackets on the top. Aach Top
Handle with 200mm Rods and ghten the
knobs to secure it properly.
Camera & Cage Setup

4
 Then insert 300mm male threaded rods into
the Straight Bracket and ghten knob to
properly lock them.
 Aach Shoulder Pad and insert Counter
weight into the rods. Then aach 150mm
male rods towards the front to extend it for
mounng other accessories.
 Now aach Straight Bracket at the end of
Rods and lock it ghtly with the help of
provided knob.
 Aach Juncon Rod Adapters with Front
Handle Bracket. Then aach it with rods and
secure it properly with the help of allen key.
Handle Kit Setup
 Now slide-in 300mm Knurling Rod through
the Front Bracket and ghten the knobs to
secure properly. Insert Clamps for Handle
Set into the Rod and screw Handle into the
Clamp.

5
 Finally mount Mae Box to the front of rods,
align Knicker with Lens Barrel and ghten its
knob.
YOUR FILMCITY CAMERA CAGE SHOULDER RIG KIT
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.