fine fixtures SDF1 User manual

206 Wembly Road
New Windsor, NY 12553
Phone: [phone]
Fax: [phone]
info@finefixtures.com
www.finefixtures.com
INSTALLATION
MANUAL
MODEL# SDF1 / TDF1
SHOWER
PANEL
FIXED FRAMELESS
MODELS:
SDF1-34
TDF1-34

INSTRUCTIONS THAT, IF IGNORED, COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR
INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
• We reserves the right to change, update, modify, alter, redesign this manual/product
or its policies without prior notice!
• It is your responsibility to visit the website to download or contact customer service
for the most updated version of the installation instructions.
• We shall not be liable for any injuries or property damages in connection with this
product during installation or use of this product!
INSTALLATION OF THIS PRODUCT BY AN
INEXPERIENCED INSTALLER MAY RESULT
IN PERSONAL INJURY OR DEATH!
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
2
ATTENTION!2PEOPLE ARE REQUIRED TO LIFT AND DURING
ENTIRE INSTALLATION OF THIS PRODUCT
NOTES:
• Limited warranty is void on any commercial installation.
• We are not responsible for local code compliance for this product.
• Building and plumbing codes may vary from state-to-state in accordance to your location.
• We are not responsible for providing any compliance certifications.
• We are not responsible to provide any type of certifications for this product.
• Under no circumstances we shall not be liable for any and all incidental damages sustained in
connection with this product Neither manufacture, nor distributor, nor retailer is responsible
for water damage or flood caused due to use of this product.
• Under no circumstances We shall not be liable for any and all fees, cost defect.
of installation/re-installation/removal, subsequent damage or transportation in case of the
product defect.
ATTENTION:
• Always rest glass on a leveled surface.
• The glass panels are tempered and cannot be cut.
• Fiberglass, acrylic or sheetrock construction might not be sufficiently strong enough to support the
shower door enclosure. You should use the wood framing from behind the face edge of the stall to
provide a secure mounting to the door. Apply a bead of silicone between the walls and base of the stall.
• For optimum performance, you should install the shower door perfectly level on a level surface.
• By not leveling the unit during construction the unit may leak causing possible water damage.

3
REQUIRED TOOLS
PARTS COMPONENTS
AND HARDWARE
During unpacking the product and prior to
installation inspect your new product for
any damages or missing parts.
Do not attempt to install or operate the
product if the product is damaged.
FLAT SCREWDRIVER
PHILLIPS SCREWDRIVER
PENCIL
Ø6 DRILL BIT
Ø8 DRILL BIT ALLEN KEY
DRILL SILICON GUN MEASURE TAPELEVEL
UTILITY KNIFE
5
Pieces
1
Piece
2
Pieces
Part
A
Part
B
Part
C
5
Pieces
Part
D
1
Piece
Part
E
1
Piece
Part
F
Ø8 Plastic
Anchor
Wall
Rail
Seal
Strip
Screw
Glass
Panel
Bottom
Rail
A
B
C
D
E
F

4
1.1
1.2
1.3
1
Mount the rail (B) on the wall
vertically and use a pencil to mark the
spots for screws. Keeping rail vertical
with a level.
1.1
Remove the rail and drill holes at the
marked points with size 6 drill bit.
1.2
Insert wall anchors (A) into the holes
with the help of a hammer.
1.3
Attach the rail (B) to the wall, using a
screw (D). Tighten with the Allen key.
B
D
B
A
ATTACHING THE RAIL
VERTICALLY

5
2.1
2.2
2.3
2
F
D
F
A
ATTACHING THE RAIL
HORIZONTALLY
Use a measuring tape to mark
two points on the floor that are
of equal distance from the wall.
(Make sure floor is level)
2.1
Use a size 6 drill bit to drill holes
at the marked points on the floor.
2.2
Insert the wall anchors (A) into
the floor, using a hammer.
2.3
Place the rail (F) on the floor (or
shower base), lining up the holes.
Attach the rail to the floor, using
screws (D) and the Allen key

6
3
ATTACHING SEAL
STRIPS TO GLASS
SIDES
Attach the plastic seal strips (C)
to a vertical and horizontal side
of the glass in an L shape.
E
C
C

7
4
ATTACHING THE
GLASS TO THE RAIL
Once the plastic seals are
attached to the glass, affix the
glass panel to the rail.

206 WEMBLY ROAD - NEW WINDSOR, NY 12553
P: 718.602.6060 F: 718.963.2082 - E: [e-mail]
TOLL FREE: 1.877.8FIXTURES
FINEFIXTURES.COM
FINE
FIXTURES
RETAIN THIS INSTALLATION MANUAL FOR FUTURE REFERENCE.
WAIT 24 HRS
BEFORE USE
AFTER
INSTALLATION
DRYING THE GLASS
5
SECURING THE GLASS
Secure the glass in the rail, using
a caulking gun and high-quality
clear silicone caulk.
Let the glass dry for 24 hours.
Do not touch, move, or make
wet during these hours.