fine fixtures SES1 User manual

206 Wembly Road
New Windsor, NY 12553
Phone: [phone]
Fax: [phone]
info@finefixtures.com
www.finefixtures.com
INSTALLATION
MANUAL
MODEL# SES1
SHOWER
ENCLOSURE
SQUARE
FRAMELESS
MODELS:
SES1-32
SES1-36
SES1-42

INSTRUCTIONS THAT, IF IGNORED, COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR
INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
• We reserves the right to change, update, modify, alter, redesign this manual/product
or its policies without prior notice!
• It is your responsibility to visit the website to download or contact customer service
for the most updated version of the installation instructions.
• We shall not be liable for any injuries or property damages in connection with this
product during installation or use of this product!
INSTALLATION OF THIS PRODUCT BY AN
INEXPERIENCED INSTALLER MAY RESULT
IN PERSONAL INJURY OR DEATH!
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
2
ATTENTION!2PEOPLE ARE REQUIRED TO LIFT AND DURING
ENTIRE INSTALLATION OF THIS PRODUCT
NOTES:
• Limited warranty is void on any commercial installation.
• We are not responsible for local code compliance for this product.
• Building and plumbing codes may vary from state-to-state in accordance to your location.
• We are not responsible for providing any compliance certifications.
• We are not responsible to provide any type of certifications for this product.
• Under no circumstances we shall not be liable for any and all incidental damages sustained in
connection with this product Neither manufacture, nor distributor, nor retailer is responsible
for water damage or flood caused due to use of this product.
• Under no circumstances We shall not be liable for any and all fees, cost defect.
of installation/re-installation/removal, subsequent damage or transportation in case of the
product defect.
ATTENTION:
• Always rest glass on a leveled surface.
• The glass panels are tempered and cannot be cut.
• Fiberglass, acrylic or sheetrock construction might not be sufficiently strong enough to support the
shower door enclosure. You should use the wood framing from behind the face edge of the stall to
provide a secure mounting to the door. Apply a bead of silicone between the walls and base of the stall.
• For optimum performance, you should install the shower door perfectly level on a level surface.
• By not leveling the unit during construction the unit may leak causing possible water damage.

3
FLAT SCREWDRIVER
PHILLIPS SCREWDRIVER
PENCIL
Ø6 DRILL BIT
Ø8 DRILL BIT ALLEN KEY
DRILL SILICON GUN MEASURE TAPE
REQUIRED TOOLS
PARTS COMPONENTS
AND HARDWARE
During unpacking the product and prior to
installation inspect your new product for
any damages or missing parts.
Do not attempt to install or operate the
product if the product is damaged.
LEVEL
UTILITY KNIFE
1
Piece
Part
M
1
Piece
Part
N
2
Pieces
Part
O
1
Piece
Part
P
12
Pieces
2
Pieces
4
Pieces
Part
A
Part
B
Part
C
2
Pieces
Part
D
1
Piece
Part
E
2
Pieces
Part
F
2
Pieces
1
Piece
Part
G
Part
H
1
Piece
Part
I
1
Piece
Part
J
2
Pieces
1
Piece
Part
K
Part
L
Plastic
Anchor
Support
Arm
Wall
Bracket
Seal
Strip
Glass
Panel
ST4 x 30
Screw
Door
Hinge
Door
Handle
Seal
Strip
ST4 x 20
Screw
Bottom
Hinge
Seal
Strip
Bottom
Threshold
Glass
Door
Seal
Strip
Glass
Panel
A
B
C
D
E
F
G
I
J
K
L
M
H
N
O
P
ST4x20

4
ATTACHING THE BASE
Attach the base to the floor of the
shower area. (Professional install
recommended)
1

5
PREPARING THE FIRST
FIXED GLASS PANEL
2.1
Attach the plastic seal (D) to a
side of the fixed glass panels (E,
P), as shown.
2.2
Attach the joints (C) to one side
of the panel (over the seal), using
screws included with the joints.
2.1
2.2
2
A
D
C
P
E
F

6
ATTACHING THE FIXED
PANELS
3.1
Use a pencil to mark the screw
points in the wall, based on the
location of the joints (C).
3.2
Use a size 6 drill bit and insert the
wall anchors (A) at the drilled
points.
3.3
Attach the joints to the wall with
screws (F), using a screwdriver.
3.4
Attach the joints (C) to the fixed
panel (E, P) using screws included
with the joints.
3
3.1 3.2 3.3 3.4
F
A
C
3/4"
3/4"

AF
7
ATTACHING THE
SUPPORT ARM
support arm (B)
4.1
Use a pencil to mark the screw
points for the support arm (B) on
the wall. Use a size 6 drill bit to
drill holes at the marked points.
4.2
Insert the wall anchors (A) into
the holes in the wall.
4.3
Attach one end of the support
arm (B) to the wall, using screws
(F).
4.4
Attach the other end of the
support arm (B) to the fixed
panels (C, P) using screws includ-
ed with the door stop. Tighten
with the Allen key.
4
4.1 4.2 4.3 4.4
BB

8
ATTACHING THE
DOOR HINGES
5.1
Attach the door hinges (G) to the
fixed glass (E) panel using screws
included with the door hinges.
5
5.1
G
E

6
9
ATTACHING THE GLASS-
TO-GLASS HINGE
6.1
Use a pencil to mark the points
where the screws for the bottom
hinge (K) will be drilled.
6.2
Use a size Ø6 drill bit to drill holes
at the marked points to insert the
screws.
6.3
Inset plastic anchor (A) and attach
the glass-to-glass bottom hinge
(K) to the first fixed panel (E, P)
using screws (J) over threshold
(M).
6.4
Follow the same steps as above
for the 2nd bottom hinge as
shown.
6
P
KM
6.1 6.2 6.3 6.4
M
K
J
P
AJ
M K

O
N
P
N
E
7
7.1 7.2 7.3 7.4
10
ATTACHING THE GLASS
DOOR JOINTS
7.1
Attach the door (N) to the joints
of the fixed glass panel (E) using
screws included with the joints.
7.2
Affix plastic seals (I) to the
bottom and lengths of the glass
door (N).
7.3
Affix plastic seals (O) to the
bottom and lengths of the glass
door (N) and fixed panel (P).
7.4
Affix plastic seals (L) to the
bottom and lengths of the glass
door (N).
L
I
N

11
8
8.1
ATTACHING THE DOOR
HANDLES
8.1
Attach the shorter door handle
(H) vertically to the outer side of
the glass door using screws
included with the handles.
Attach the larger door handle (H)
vertically to the inner side of the
glass door using screws included
with the handles.

12
9
SECURING THE GLASS
DOOR
Secure the screws on the glass
door with the Allen key.
Note: The correct position of
the door is shown below:
B
D
B
D
B
D
✓ ✕ ✕

13
10
8.1
COMPLETING THE ASSEMBLY
Secure the seals, panels, and door
with caulking gun and high-quality
silicone or bathroom grade caulk.

WAIT 24 HRS
BEFORE USE
AFTER
INSTALLATION
14
11
DRYING THE DOOR AND PANELS
Leave the shower unused for 24 hours,
so that it can dry completely.

206 WEMBLY ROAD - NEW WINDSOR, NY 12553
P: 718.602.6060 F: 718.963.2082 - E: [e-mail]
TOLL FREE: 1.877.8FIXTURES
FINEFIXTURES.COM
FINE
FIXTURES
RETAIN THIS INSTALLATION MANUAL FOR FUTURE REFERENCE.