Finelite HP-2 Guide

© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98540. V3 EFFECTIVE DATE: 08/26/19
HP-2 / HP-4 / HP-6 Driver Replacement Instructions
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.comThis is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary. 1of 5
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Overview
Uplight Driver Replacement
Pages 4-5
Downlight Driver Replacement
Pages 2-3
0-10V
Dimming
Driver
Replacement
• All power connections should be installed according to
local/national codes by a Certified Electrician.
• This installation requires proper support as each luminaire
is being installed.
• DO NOT attempt to join luminaires together on the floor.
Damage may result when lifted.
NOTES
HELPFUL
VIDEOS
Effortless
Access
Louver
Removal

2of 5
HP-2 / HP-4 / HP-6 Downlight Driver Replacement Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98540. V3 EFFECTIVE DATE: 08/26/19
Effortless
Access
Step 1 - Opening Luminaire
A. Remove Diffuser or Louver
Backplate
Backplate
Flathead
Screwdriver
Clip
Backplate
• Carefully rotate backplate out and let it hang from luminaire body.
Putty Knife OptionRemove Diffuser
Remove Louver (HP-2 & HP-4 ONLY) Flathead Screwdriver Option
Clip
Backplate
Putty
Knife
B. Release Backplate
• CAUTION: Wear gloves to keep diffuser or louver surface clean.
• Carefully remove diffuser or louver and set aside to prevent from getting dirty or damaged.
• FOR LOUVER: Release louver by inserting the blade of a putty knife approximately
1" behind louver edges and pry down.
• Ensure diffuser or louver can be clearly identified back to its corresponding luminaire.
Backplate
• Release backplate from clips by sliding the blade of a putty knife behind backplate edges.
• To use a flathead screwdriver, press end of screwdriver (from inside the luminaire) against the clip, until the
backplate is released.
Louver
Removal
Diffuser
Putty KnifeLouver
NOTE:For White Cross Blade Baffle, refer to
Baffle Tether Addendum before installing.

3of 5
HP-2 / HP-4 / HP-6 Downlight Driver Replacement Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98540. V3 EFFECTIVE DATE: 08/26/19
0-10V
Dimming
Driver
Replacement
NOTE:For White Cross Blade Baffle, refer to
Baffle Tether Addendum before installing.
A. Release Driver B. Replace Driver
Step 2 - Replace Driver
• Release driver from luminaire by removing mounting screws.
• Disconnect driver from driver harness.
• Once driver is free, disconnect electrical connections from the driver.
• Replace with new driver and reconnect all electrical connections.
• Replace backplate by snapping back into clips.
• CAUTION: Wear gloves to keep diffuser or louver surface clean.
• NOTE: For White Cross Blade Baffle, refer to Baffle Tether Addendum before installing.
• Replace diffuser or louver and turn power on.
Electrical Connectors
Driver Harness
Driver
Screw
Washer
WIRING LEGEND
Black Hot Line Voltage
White Neutral Line Voltage
Green Ground
Grey Dimming 0-10V DC
Purple Dimming 0-10V DC
Driver Harness
Part # 15501

4of 5
HP-2 / HP-4 Uplight Driver Replacement Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98540. V3 EFFECTIVE DATE: 08/26/19
A. Remove Diffuser
• To release backplate, use a putty knife to slip behind backplate edges and release them from clips.
• Lift backplate out of housing channel, pulling wiring harnesses through the housing.
• Let backplate rest atop of luminaire. DO NOT disconnect LED board harnesses.
Uplight Backplate
Putty Knife
Backplate
Clip
Harness
B. Release Backplate
Diffuser
• Remove diffuser and set aside to prevent from getting dirty or damaged.
Effortless
Access
Step 1 - Opening Luminaire
For Indirect Only

5of 5
HP-2 / HP-4 Uplight Driver Replacement Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98540. V3 EFFECTIVE DATE: 08/26/19
Step 2 - Replace Driver
A. Release Uplight Driver B. Replace Uplight Driver
• Release driver from luminaire by removing mounting screws.
• Disconnect driver from driver harness.
• Once driver is free, disconnect electrical connections from the driver.
Driver
Screw
Washer
• Replace with new driver and reconnect all electrical connections.
• Replace backplate by snapping back into clips.
• Replace diffuser and turn power on.
0-10V
Dimming
Driver
Replacement
Electrical Connectors
Driver Harness
Driver
WIRING LEGEND
Black Hot Line Voltage
White Neutral Line Voltage
Green Ground
Grey Dimming 0-10V DC
Purple Dimming 0-10V DC
Driver Harness
Part # 15501