Finelite HP-WG User manual

Patent Pending
HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
1 of 10
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.comThis is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.
Overview
• All power connections should be installed according to
local/national codes by a Certified Electrician.
• This installation requires proper support as each luminaire
is being installed.
• DO NOT attempt to join luminaires together on the floor.
Damage may result when lifted.
NOTES
HELPFUL
VIDEO
0-10V
Dimming
Simple
Plug-Together
Wiring
Stud
Wall
T-Bar
Step 1
Mounting Locations & Methods
Page 2
Step 2
Identification & Preparation
Page 3
Step 5
Joining Luminaires
Page 8
Step 6
Closing Luminaires
Pages 9-10
Step 4
Mounting Starter to Structure
Pages 6-7
Step 3
Feed Locations & Options
Pages 4-5

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
2 of 10
B. Mounting LocationsA. Create Rough In
Alternative "L" Bracket Mounting (by others) Alternative Mount to Structure (by others)
Step 1 - Mounting Locations & Methods
Top ViewSide View
Luminaire Length A (in) B (in)
2' 3 18
3' 3 30
4' 6 36
8' 6 84
Luminaire Depth Rough In Opening (in)
2", 4" & 6" Z = 6-1/2
Y
"L" Bracket
(by others)
T-Bar T-Bar
1/8"
Endcap
The Pocket Slot Endcap adds 1-1/4" for Spackle Flange and 1" for
T-Bar per endcap.
Luminaire Depth Y (in)
2" 5-1/8
4" 7-1/8
6" 9-1/8
Spackle Flange T-Bar
1-1/4"
Drywall
Drywall Screw
1"
Ceiling Tile
Endcap Information (Side Views):
The Wall-to-Wall Endcap adds 1/8" per endcap.
Wall
A
2"
B
Wall
Mounting Location Top Feed (standard)
1/2"
Endcap
1/2"
Endcap
1/2"
Wall
1/2"
Tab
Luminaire
Support Wire
(by others)
Use appropriate hardware (by others)
to secure "L" Bracket to luminaire.
In addition to alternative mounting
methods, luminaire must be
secured to structure by support
wire (by others) per building code.
Max. 3/8"
Structural Blocking (by others)
Luminaire Depth X (in) Y (in)
2" 6-5/8 5-1/8
4" 6-5/8 7-1/8
6" 6-5/8 9-1/8
Wall
X
Y
1/2"
Z

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
3 of 10
HP-WG - 6W - 4D - 32' - S - 830 - 120V - SC - TR
ABC Corporation - A12345
HP-WG - 6W - 4D - X' STARTER
ID: 1
Factory Order
Number
Job Name
Unique Luminaire
ID Number
Full Catalog
Order ID
Luminaire
Section Type
Luminaire Type
and/or Run Length
Step 2 - Identification & Preparation
CAUTION
Arrange luminaires in order
according to ID# at their
install locations.
A. Identify Luminaires
Kitted Hardware
• Finelite has provided items
listed here, with their Finelite
part numbers. These items
can be found in separate
boxes shipped with the
luminaire.
• Account for all parts and set
aside until they are needed.
• All other hardware needed
for this installation will be
by others.
ID Label
#8-18 x 1/4" Screw
Part# 69026
Feed Locations & Options
p. 4, Step 3
Mounting Starter to Structure
p. 6-7, Step 4
Joining Luminaires
p. 8, Step 5
Closing Luminaires
p. 9-10, Step 6
#10-32 Screw
Part# 94144
Feed Locations & Options
p. 4, Step 3
Extrusion Joiner Bracket
Part# 11302
Joining Luminaires
p. 8, Step 5
T-Bar Bracket
Part# 11303
Closing Luminaires
p. 10, Step 6
Cover Sleeve
Part# 10719
Closing Luminaires
p. 10, Step 6
• Identify all luminaires by their ID label that can be found on the box and inside the luminaire.
• NOTE: Exact location of labels in these areas may vary.
• Remove all luminaires from their box.
• Refer to Record Drawings that can be found in the hardware kit.
'
HP-WG - 6W - 4D - 32'- S - 830- 120V - SC- TR
ABC Corporation - A12345
HP-WG - 6W - 4D - X STARTER
ID: 1
Starter
Flexible Mounting Plate
Bottom-Up View

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
4 of 10
0-10V
Dimming
WIRING LEGEND
Black Hot Line Voltage
White Neutral Line Voltage
Green Ground
Grey Dimming 0-10V DC
Purple Dimming 0-10V DC
Step 3 - Feed Locations & Options
1/4"-20 Threaded Rod (by others)
Endcap Feed (optional)
CONTINUED
Top Feed (standard)
#10-32 Screw
(provided)
Power Feed
Wall Feed (optional)
Power Feed
#8-18 x 1/4" Screw
(provided)
#8-18 x 1/4" Screw
(provided)
#10-32 Screw
(provided)

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
5 of 10
Top Feed
Wall Feed Endcap Feed
Top View
Back View Side View
5-9/16"
D
1/4"-20 Threaded Rod (by others)
Wall Feed (optional)
F
GEndcap Feed (optional)
Wall
Luminaire Length C (in)
2' 5
3' 5
4' 12
8' 12
Luminaire Width F (in) G (in)
6" 2 13/16
Luminaire Depth D (in)
2" 3-5/16
4" 5-5/16
6" 7-5/16
Step 3 - Feed Locations & Options
T-Bar
C6"
2"
Wall
Top Feed (standard)
Top Feed Location (standard)
• Use chart above to find measurement of C for feed location.
• NOTE: For tailored length luminaire power feed locations, contact factory.

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
6 of 10
Step 4 - Mounting Starter to Structure
Starter
Kickplate
A. Open Kickplate B. Remove CarrierBottom-Up View Side View
Housing Bracket Housing
Bracket
Driver
Carrier
Kickplate
#8-18 x 1/4" Screw (provided)
#8-18 x 1/4" Screw
(provided)
Safety Cable
Wall
• Make electrical connections according to feed location and options.
• To access carrier, open kickplate by unsnapping along the whole length of the luminaire (about every 6").
• Once kickplate has been opened, remove the #8-18 x 1/4" screw and slide carrier toward wall to detach from housing.
• NOTE: The carrier will be suspended by safety cables but you can remove them for complete open access.
CONTINUED

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
7 of 10
Step 4 - Mounting Starter to Structure
1/4" Washer
(by others)
1/4"-20 Nut
(by others)
Starter
Flexible Mounting Plate
1/4" Washer (by others)
1/4"-20 Nut (by others)
"L" Bracket (by others)
Appropriate Fastening Hardware (by others)
C. Mount Luminaire
1/4"-20 Lag Bolt
(by others)
#8-18 x 1/4" Screw
(provided)
"L" Bracket
(by others)
MOUNT TO THREADED ROD (Standard)
• Mount the luminaire to structure using a 1/4"-20 nut and washer on a threaded rod.
• NOTE: The flexible mounting plate can move for a precise fit.
• If there is no joiner/ender, then tighten nuts fully. PROCEED TO STEP 6.
MOUNT TO "L" BRACKET (Optional)
• Mount the luminaire to structure using an "L" bracket with appropriate fastening hardware.
• NOTE: The flexible mounting plate can move for a precise fit.
• If there is no joiner/ender, then tighten nuts fully. PROCEED TO STEP 6.
MOUNT TO STRUCTURE (Optional)
• Mount the luminaire to structure using appropriate fastening hardware.
• NOTE: The flexible mounting plate can move for a precise fit.
• If there is no joiner/ender, then tighten fully. PROCEED TO STEP 6.
Appropriate Fastening Hardware (by others)
1/4"-20 Threaded Rod
Structural Blocking (by others)
Bottom-Up View
Standard Option 1 Option 2
Side View Side View

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
8 of 10
CAUTION
DO NOT attempt to join
luminaires together on the floor.
Damage may result when lifted.
Follow these instructions.
Simple
Plug-Together
Wiring
A. Install Joiner/Ender
Step 5 - Joining Luminaires
Plug-Together Wiring
Aligner Plate
Ceiling
Ceiling
Wall Wall
Starter Starter
Joiner/Ender
Bottom-Up View C. Plug-Together Wiring Bottom-Up View
• Connect the plug-together wiring.
• Secure all luminaires by tightening all nuts to threaded rods.
B. Secure Joiner Brackets Side View
Starter
Top
Bottom
Joiner/Ender
Joiner/
Ender
Aligner Plate
T-Bar
Joiner Bracket
#8-18 x 1/4" Screw
(provided)
T-Bar
Extrusion Joiner Bracket
(provided)
• Slide the joiner/ender luminaire over the aligner plate on the installed luminaire.
• See Step 3C for how to secure a joiner/ender luminaire to structure.
• NOTE: Slightly tilt starter and joiner/ender luminaires before installing onto wall.
• Ensure that the holes are aligned on the plate.
• Fasten the joiner/ender luminaire to the aligner plate using a #8-18 x 1/4" screw.
• Secure the joiner brackets using a #8-18 x 1/4" screw.
• CAUTION: Do not over-tighten.
#8-18 x 1/4" Screw
(provided)
#8-18 x 1/4" Screw
(provided)

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
9 of 10
A. Replace Carrier
Step 6 - Closing Luminaires
Side View
CONTINUED
B. Secure Carrier & Snap Kickplate Side View
Kickplate
Housing Bracket
#8-18 x 1/4" Screw (provided)
Housing Bracket
Carrier
Carrier
#8-18 x 1/4" Screw
(provided)
• Hook carrier to the housing brackets.
• Secure carrier with #8-18 x 1/4" screw.
• Rotate kickplate and snap back into place along the whole length of the luminaire (about every 6").

HP-WG Post-Ceiling T-Bar Installation Instructions
© 2019 FINELITE, INC. ALL RIGHTS RESERVED. Form - 98423. V3 EFFECTIVE DATE: 01/29/19
10 of 10
Step 6 - Closing Luminaires
C. Secure to Structure D. Final Step - Install Cover SleeveSide View Side View
Bend Here
T-Bar Bracket (provided)
Wall
T-Bar
#8-18 x 1/4" Screw
(provided)
T-Bar Bracket
(provided)
#10 Screw
(by others)
• 1. Hook back edge of cover sleeve over edge of carrier.
• 2. Snap front edge of cover sleeve in place along the whole length of the luminaire (about every 6").
• Once cover sleeve is in place, turn power on to luminaire.
FOR T-BAR:
• Gently bend T-Bar bracket so it aligns with T-Bar.
• Secure T-Bar bracket to T-Bar extrusion using #8-18 x 1/4" screw.
• Secure T-Bar bracket to T-Bar using self-drilling screws.
FOR WALL:
• Secure T-Bar bracket to wall using appropriate #10 screws.
12
Cover Sleeve (provided)
Carrier
T-Bar Extrusion
Self-Drilling Screw (by others)
#10 Screw (by others)
T-Bar Bracket (provided) T-Bar Bracket (provided)
#8-18 x 1/4" Screw
(provided)
Cover Sleeve
(provided)