Finishing Touch Yes! User manual

Thank you for your purchase of the
Finishing Touch (FT) Yes! Please follow
these simple steps to begin
eliminating unwanted hair easily!
1. Fully charge unit prior to first use.
(It takes approximately 2.5 hours for unit to
fully charge)
2. Make sure skin is clean and dry.
3. Turn switch to ON position. Purple Sensa Light™
Head and green LED will flash.
4. Position the touch activated Sensa Light™Head
against the skin to begin hair removal. (Unit will
not operate until it touches skin.)
5. Remove hair by gliding the unit in the opposite
direction of hair growth for best results.
6. For shorter hair or stubble, change to Microfoil
Head.
7. Unit will turn off when not in use. Turn switch to
OFF position when finished to save battery.
For complete usage please see full instructions inside
• WATER WILL DAMAGE THE FT Yes! Do not use the unit in the shower, near water,
or in a damp room.
• DO NOT RINSE THE HEAD UNDER WATER! To clean the head, use the brush that
is included in the package. Make sure the unit is turned off.
• FT Yes should be switched off and stored in a cool dry place when not in use.
• For best performance, it is NOT recommended to use the FT Yes while it is charging.
MICROFOIL HEAD MAINTENANCE
To maintain optimal performance of the Microfoil Head, from time to time clippings
trapped in the head may need to be cleaned out. The Microfoil Head is designed for
easy removal and may be easily cleaned by removing the head from the FT Yes, then
gently tapping the bottom of the head against a hard surface, such as a sink. The
brush included with the FT Yes may be used to swipe out any remaining clippings.
Compressed air, such as computer duster, may also be used to blow the clippings
from the Microfoil Head.
The main body of the FT Yes underneath the head should also be brushed or blown
clean any time the head is cleaned or changed.
SENSA-LIGHT™ HEAD MAINTENANCE
The performance of the Sensa-Light™ Head may be kept at optimal level with regular
cleaning (as described above) and lubrication of the Sensa-Light™ Head. To lubricate
the Sensa-Light™ Head, after cleaning, apply a drop or two of mineral oil (or baby oil)
to the front edge.
• Keep out of reach of children.
• Exercise caution when using around eyes.
• The FT Yes contains a Lithium ion battery. DO NOT DISPOSE OF IN FIRE.
Wayne, NJ 07470
Made in China © 2015 Ideavillage
[email protected]
FTYQVCWEB092115
This device complies with part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device
must accept any interference
received, including interference
that may cause undesired operation.
Notice: Changes or modification not
expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.

NOTE: Prior to first use, fully charge FT Yes for
approximately 2.5 hours.
FT Yes must be charged with the supplied USB cable,
using either the supplied AC adapter or an alternate
USB source.
While the unit is charging, the red light will remain on.
The green LED will remain on when unit is connected to the
adapter and fully charged. Charge will hold approximately 60
minutes run time.
DANGER: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY
FOLLOW THESE INSTRUCTIONS.
FOR CONNECTION TO A SUPPLY NOT IN THE U.S.A., USE AN ATTACHMENT PLUG
ADAPTER OF THE PROPER CONFIGURATION FOR THE POWER OUTLET.
Use on clean and completely dry skin with
no cream or cosmetic residue.
1. Remove cover (see Image 1).
2. Move switch to ON position (toward head)
(see Image 2).
3. Purple Sensa-Light™ Head and green LED will flash
(see Image 3).
4. Position the Sensa-Light™ Head against the skin to
begin hair removal. This unit will not begin to
work until contact has been made with
skin. The purple Sensa-Light™ Head and the green
activation LED will remain on while the unit is in
use. Place the FT Yes on skin and gently glide the
head of the unit along skin in the opposite direction
of hair growth at a 45° angle (NOT at a 900
angle) (see Image 4).
DO NOT APPLY EXCESSIVE PRESSURE
DURING USE to avoid damage to skin or head of
unit. Discontinue use if any skin irritation results.
5. For short hair, stubble or touch-ups, select the touch
activated Microfoil Head (see Image 5). For best
results while using the Microfoil Head, hold the
FT Yes at a 900angle to skin (NOT on a 45°
angle) and apply SLIGHT pressure (see Image 6).
NOTE: For more effective hair removal, make
sure to trim hair as short as possible using the
Sensa-Light™ Head prior to using the Microfoil
Head.
6. FT Yes will turn off within approximately 6
seconds. Green LED will return to flash. Unit will
automatically turn on again when it comes in
contact with skin.
7. When finished using your FT Yes, turn switch to
OFF position (away from head), cover and store
in cool dry place.
450
angle
450
angle
900
angle
900
angle
Image 4
Usage for Sensa-Light™ Head
Image 6
Usage for Microfoil Head
To change / replace heads, place your thumbs on the back
of the unit. Push gently in the direction of the arrow, toward
the front and in an upward motion. The head will separate
from the body. (Image 7)
Line up new head with arrow on back of unit and press.
Head will click into position. (Image 8)