Fire-Lite CRF-300 User manual

Before Installing
This information is included as a quick reference installation guide. Refer to the control panel installation manual for detailed system
information. If the modules will be installed in an existing operational system, inform the operator and local authority that the system
will be temporarily out of service. Disconnect power to the control panel before installing the modules.
NOTICE: This manual should be left with the owner/user of this equipment.
General Description
The CRF-300 Relay Control Module is intended for use in addressable, two-wire systems, where the individual address of each module is
selected using the built-in rotary switches. It allows a compatible control panel to switch discrete contacts by code command. The relay
contains two isolated sets of Form-C contacts, which operate as a DPDT switch and are rated in accordance with the table in the manual.
Circuit connections to the relay contacts are not supervised by the module. The module also has a panel controlled LED indicator. This
module can be used to replace an C304 module that has been configured for Form-C operation.
Compatibility Requirements
To ensure proper operation, these modules shall be connected to listed compatible system control panels only.
Mounting
The CRF-300 mounts directly to 4” square electrical boxes (see Figure 2A). The box must have a minimum depth of 21/8”. Sur-
face mounted electrical boxes (SMB500) are available.
NOTE: All wiring must conform to applicable local codes, ordinances, and regulations. When using control modules in nonpower limited
applications, the CB500 Module Barrier must be used to meet UL requirements for the separation of power-limited and
nonpower-limited terminals and wiring. The barrier must be inserted into a 4”x4”x21/8” junction box, and the control module must
be placed into the barrier and attached to the junction box (Figure 2A). The power-limited wiring must be placed into the isolated
quadrant of the module barrier (Figure 2B).
1. Install module wiring in accordance with the job drawings and appropriate wiring diagrams.
2. Set the address on the module per job drawings.
NOTE: Some panels support extended addressing. In order
to set the module above address 99 on compatible
systems, carefully remove the stop on the upper rotary
switch with thumb in the direction shown in Figure 1.
3. Secure module to electrical box (supplied by installer),
as shown in Figure 2A.
Specifications
Normal Operating Voltage: 15 to 32 VDC
EOL Resistance: Not used
Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)
Humidity: 10% to 93% Noncondensing
Dimensions: 41/2” H x 4” W x 11/4” D (Mounts to a 4” square by 21/8” deep box.)
Accessories: SMB500 Electrical Box; CB500 Barrier
CRF-300 Relay Control Module
Installation Instructions
Figure 1. Controls and indicators:
Figure 2A. Module mounting with barrier:
Figure 2B:
A78-2610-08
F300-04-00 1 I56-1190-01
Fire•Lite Alarms, Inc., One Fire-Lite Place, Northford, CT 06472, 203-484-7161
ISOLATED
QUADRANT
0
1
2
3
4
9
8
7
6
5
0
TENS
ONES ADDRESS
LOOP
9
8
7
6
5
4
321
0
9
8
7
6
5
4
321
10
11
12
13
14
15
A78-2318-08
A78-2611-11
0
1
2
3
4
9
8
7
6
5
0
TENS
ONESADDRESS
LOOP
9
8
7
6
5
4
321
0
9
8
7
6
5
4
321
10
11
12
13
14
15
9
8
7
6
54
3
2
1
0
0
1
2
3
456789
TENS
ONES
ADDRESS
LOOP
0
78
6
5
4
3
21
910
11
12
13
14
15

WARNING
All relay switch contacts are shipped as shown in Figure 3, but may have transferred during shipping. To ensure that the switch con-
tacts are in their correct state, modules must be made to communicate with the panel before connecting circuits controlled by the mod-
ule.
Relay Contact Ratings:
Figure 3. Relay module wiring diagram:
A78-2286-10
F300-04-00 2 I56-1190-01
©1999 Fire•Lite Alarms, Inc.
CURRENT RATING MAXIMUMVOLTAGE LOAD DESCRIPTION APPLICATION
3 A
2 A
.9 A
.9 A
.5 A
1 A
.5 A
30 VDC
30 VDC
110 VDC
125 VAC
30 VDC
30 VDC
125 VAC
Resistive
Resistive
Resistive
Resistive
Inductive (L/R=5ms)
Inductive (L/R=2ms)
Inductive (PF=.35)
Non Coded
Coded
Non Coded
Non Coded
Coded
Coded
Non Coded
.7 A 75 VAC Inductive (PF=.35) Non Coded
IF ANY WIRING TO TERMINALS 3 – 9 IS NONPOWER
LIMITED, THE CB500 BARRIER IS REQUIRED. THE CB500
INCLUDES A NONPOWER LIMITED LABEL, WHICH MUST
BE PLACED OVER THE POWER LIMITED TERMINAL
INFORMATION ON THE NAMEPLATE LABEL.
MODULE
FROM PANEL OR
(+)
(—)
TO NEXT
(+)
(—)
DEVICE
(+)
(—)
CONTROL
CONNECT MODULES TO LISTED COMPATIBLE
RELAY COMMON 1
RELAY COMMON 2
NORMALLY CLOSED 1
NORMALLY OPEN 2
NORMALLY CLOSED 2
MODULE DOES NOT SUPERVISE CONTROLLED CIRCUITS
NORMALLY OPEN 1
FIRE LITE CONTROL PANELS ONLY
PREVIOUS DEVICE
COMMUNICATION LINE
32 VDC Max.
SHIELDED-TWISTED PAIR
IS RECOMMENDED
9
8
7
6
54
3
2
1
0
ADDRESS
LOOP