Fireboy- Xintex FR-1000 User manual

18131 Rev 3.0
1
.
Introduction
Thank you for purchasing the FR-1000/2000 Fire Alarm Monitor. Fireboy-Xintex, Inc. is
very proud to be able to provide this product to you. You have selected a capable
system designed to provide years of reliable service under the most demanding
conditions.
The FR-1000/2000 Fire Alarm Monitor is a versatile, compact, modern, stylish, user-
friendly intelligent network system. Our Research and Development Team have
developed this system specifically for the marine environment using proven techniques
and materials, which will ensure a long life at sea.
The FR-1000/2000 provides features found only in expensive computer-based systems
on mega-yachts, but does so for a fraction of the cost. It is an economical and capable
alternative to simplistic monitoring systems. The FR-1000/2000 allows builders and
retrofitters to offer a system with maximum functionality.
FR-1000/2000 Installation Manual

18131 Rev 3.0
2
Installation
WARNING!!
This equipment is NOT intended for use in the following locations and requiring
exceptional degrees of protection
Locations requiring an exceptional degree of protection means - a location exposed
to weather, seas, splashing, pressure-directed liquids, or similar moisture
conditions. These locations include--
(1) On deck;
(2) A machinery space;
(3) A cargo space;
(4) A location within a galley or pantry area, laundry, or water closet which
contains a shower or bath; and
(5) Other spaces with similar environmental conditions.
1. The FR-1000/2000 should be mounted in a convenient location, preferably where
the visual indicators may be readily seen. To install the display, you must first
remove the screw on bezel.
2. Next, drill a 2-1 /16” diameter hole into the panel. Slip the instrument through the
hole and secure with the threaded bezel.
3. Install the detectors using directions included with each detector.
4. Wire the Battery + and Battery –leads to an appropriate voltage source (9-
30Vdc)
5. On the FR-1000 wire the detector loop to the White and Black wires connected to
White (Zone +) and Black (Zone –). See following pages for diagrams.
6. The FR-2000 has two zones. Wire the first zone the same as the FR-1000 and
the second zone to Blue (Zone +) and Black (Zone -).
7. The buzzer comes pre-wired to the mating harness so no additional wiring
required.
8. The pre-wired buzzer may be replaced with an alternative indicator. The current
draw of the device must not exceed .75A or 750mA.

18131 Rev 3.0
3

4
Connecting One Sensor per Zone
4K7
2.2K EOL Resistor-12V
5.6K EOL Resistor-24V
R
L or In+
L1 or Com
L2 or Out+
Wiring for door switches or contact
sensors
1k ohm
Normally open switch.
Switch closes when door
is opened.
Black (Zone -)
FR Harness
White (Zone +)
2.2K EOL Resistor-12V
5.6K EOL Resistor-24V
Black (Zone -)
FR Harness
White (Zone +)

5
Connecting Apollo Sensors

6
Connecting Orbis Sensors

7
Operation
“OK” LED On = system is all ok.
“FAULT” LED On = either open or shorted smoke detection cable or sensor.
If there is a short on the line:
If a short is detected on the line the “OK “LED will turn off, the “FAULT” LED and alarm
will turn on, the Sensor Output will also be turned off. When the “SILENCE / RESET
“button is pushed the “FAULT” LED will turn off and the zone “OK” LED will flash for one
minute, after the one minute delay the Sensor Output will turn on again to check the line.
This procedure will repeat until the short is removed.
If the line is open circuit:
If an open circuit is detected on the line the “OK“ LED will turn off, the “FAULT” LED and
alarm will turn on. When the “SILENCE/RESET“ button is pushed the alarm will be
muted. When the system detects the EOL resistor the “FAULT” LED will turn off and the
“OK” LED will turn on.
“FIRE” LED On = A sensor has detected smoke or heat.
SILENT / RESET Button:
This button will mute the audible alarm and reset the sensors.
TEST Button:
If the TEST button is pressed for three seconds the unit will go into Test mode.
All LED’S and the alarm will turn on for five seconds.
Electrical Specifications FR-1000/2000
Minimum (alarm current) = 10mA
Operate voltage = 9 - 30vdc
Maximum current per zone = 320mA (including EOL)
Siren/Buzzer output = 12vdc @ 800mA
Supply voltage @ 12vdc
Maximum sensors = 14 per zone
Must use 2k2 EOL resistor
Supply voltage @ 24vdc
Maximum sensors = 8 per zone
Must use 5k6 EOL resistor

8
All technologies, design and Intellectual Property is owned by
Manufactured for Fireboy-Xintex, Inc.
P.O. Box 152 Grand Rapids, MI. USA 616-735-9380
www.fireboy-xintex.com
One (1) Year Limited Warranty
This Warranty is in lieu of all other express or implied warranties.
Seller warrants title, materials, and workmanship on Fireboy equipment and
assigns, the original manufacturer’s warranty on those components
manufactured by others, as permitted. Seller’s warranty shall be for a period
of (1) one year from the date of sale to the ORIGINAL CONSUMER
Fireboy-Xintex, Inc. does not assume the costs of removal and/or
installation of the product or any other incidental costs which may arise as a
result of any defect in materials or workmanship. Any non-conforming
equipment returned to the Seller at Buyer’s expense and risk shall be
repaired or replaced at Seller’s option, provided that: (a) the product has not
been subjected to abuse, contamination, neglect, accident, incorrect wiring
not our own, improper installation or servicing, or used in violation of the
instructions furnished by Fireboy-Xintex, Inc. (b) the product has not been
repaired or altered by anyone other than Fireboy-Xintex, Inc. (c) the serial
number has not been removed, defaced, or otherwise changed (d) the
product is determined to contain defective materials or workmanship: and
(e) use of the product is discontinued upon discovery of detective materials
or workmanship and Fireboy-Xintex Inc. is notified immediately.
ANY WARRANTY IMPLIED BY LAW, INCLUDING WARRANTIES OF
MERCHANTABILITY OF FITNESS, IS IN EFFECT ONLY FOR THE
DURATION OF THE EXPRESS WARRANTIES, OR TO ASSUME FOR
FIREBOY/XINTEX, INC., ANY OTHER LIABILITY IN CONNECTION WITH
THE SALE OF ITS PRODUCTS. FIREBOY/XINTEX, INC. SHALL BE NOT
LIABLE FOR THE LOSS OF USE, REVENUE, PROFIT, INJURY OR ANY
OTHER CONSEQUENTIAL OR INCIDENTAL DAMAGES. BUYER IS NOT
RELYING ON SELLER’S JUDGEMENT REGARDING BUYERS
PARTICULAR REQUIREMENTS, AND HAS HAD AN OPPORTUNITY TO
INSPECT THE PRODUCT TO BUYER’S SATISFACTION.