Firefly GoTo Seat User manual

User Manual
Family Freedom
GGGGooooTTTToooo
English
Seat

p2 GoTo Seat User Manual
English
Contents
01 Intended Use p.03
02 Certication p.04
03 Warnings and Cautions p.04
04 Terms of Warranty p.06
05 Safety Information p.06
06 Medical Device Combinations p.07
07 Precautions and Contraindictions p.08
08 Cleaning and Care Information p.09
09 Product Servicing p.11
10 Important Guidelines p.11
11 Product Inspection p.12
12 Reissuing Firey Products p.13
13 Setting up your GoTo Seat p.14
14 Using the GoTo Seat on a hardback chair p.16
15 Using the GoTo Seat on a supermarket trolley p.20
16 Attaching the GoTo Seat to the oorsitter accessory p.21
17 Recommended recline positions p.23
18 Taking GoTo Seat apart and removing upholstery p.26
19 Putting the upholstery back on and assembling GoTo Seat p.30
20 Sizing Information p.33
21 Table of Symbols p.34
22 GoTo Seat Vinyl Cleaning and Care Information p.35
The Firey GoTo Seat is a lightweight
portable seat that enhances children’s lives
through participation. It’s a safe, supportive
multipurporse seat, great for your home or
on the go.
Please read all user instructions carefully before using the GoTo Seat.
These instructions can also be downloaded from our website www.
reyfriends.come along with videos, diagrams and other useful
downloads.

GoTo Seat User Manual p3
English
SECTION 01: Intended Use
Intended Use
The GoTo Seat is a portable seating
device intended to provide postural
support to children with mild-complex
postural needs. The device is intended
to be attached to a 3rd party surface,
including but not limited to; standard
chairs, aeroplane seats, park swings.
It also can be used stand alone with
an attachment to a oor sitter device.
The GoTo Seat is not designed to be
used as a substitute for a child’s car
seat.
Indications for Use
The GoTo Seat has been designed
to provide additional upper body
postural support for children with
disabilities. The seat must be attached
to a chair or similar support structure
for stability and safety at all times.
The GoTo Seat is for occasional use
due to limited support and pressure
relief and therefore is not intended
to be used as the primary seating
system for a child with a disability.
The GoTo Seat is available in 2 size
options. Size 1 is intended for children
aged approximately 1–3 years with
a maximum weight of 15kg/33lbs*
and Size 2 is intended for children
aged approximately 3–8 years and a
maximum weight of 30kg/60lbs*.
We cannot accept responsibility for
any use of the product outside of its
intended use. Daily activities tested
and approved by Firey by Leckey for
the use of the GoTo Seat are:
1. Attached to a hard back chair
for dining with family and friends.
2. For use in a shopping trolley allowing
the parent/ guardian to shop with
greater ease.
3. As a Floorsitter with the
Floorsitter attachment.
4. For use in a pushchair allowing the
parent/guardian to be on the go.
Be aware that while your child is using the
Floorsitter it will be possible for them to move
around the oor, and so the Floorsitter must
always be used under supervision. If in any doubt
please contact Firey customer services on:
customer.enquiries@reyfriends.com
*Please note however,
the weight limit for a child
being placed into a standard
shopping trolley seat is
13kg/28.5lbs maximum.

p4 GoTo Seat User Manual
English
SECTION 02: Certification
The GoTo Seat is classied as a Class I Medical Device under EU and UK
regulations. As the manufacturer, James Leckey Design Limited, declares that
this product conforms to the Medical Device Regulation (2017/745), UK Medical
Device Regulations 2002, Medial Device Directive (93/42 EEC) and EN 12182:2012
Assistive products for persons with disability, general requirements and test
methods.
Notice to the user and/or patient: Any serious incident that has occurred
in relation to the device should be reported to the manufacturer and the
competent authority of the Member State in which the user and/or patient is
established.
NOTE:
General user advice.
Not following these instructions may result in physical injury, damage to the
product or damage to the environment!
SECTION 03: Warnings
and Cautions
Warning Toppling Hazard:
• Always read user instructions fully
before use.
Warning Finger Trap Hazard:
• Ensure that the user or carer does
not touch any moving joint or pivot
that is not locked.
• While the user is in the product,
the carer should strive to keep
product adjustments to a
minimum.
Warning Occupant Security:
• User transfers in and out of the
product must be done with
appropriate equipment and
personnel.
• Ensure that all harnesses are
securely applied.
• If the user exhibits any form of
distress, remove from the product
as quickly as is safely possible.
• Users should not be left
unattended at any time whilst
using Leckey equipment.

GoTo Seat User Manual p5
English
wear the fabric components
and encourage corrosion on the
product. Only use non-abrasive
household cleaners and moist
cloths, do not use running water
on the upholstery whilst it is still
attached to the product. See
Cleaning and Care Information of
the user manual.
Caution Cleaning Power Washer/
Hoses:
• Hoses and power washers are
not to be used to clean the
product. See Cleaning and Care
Information of the user manual.
Caution Disposal:
• When disposing of the product
using a community waste
disposal site, the components
should be disposed of separately
where appropriate.
Caution Bringing to Use:
• Before use, allow 2 hours for the
product to acclimatise to room
temperature.
• Ensure sufcient clearance of any
straps from the user’s neck, during
use of the product and transfers,
to avoid any strangulation risk.
Caution Finger Pinch Hazard:
• While the user is in the product,
the carer should strive to keep
product adjustments to a
minimum.
• Take care when assembling or
adjusting the position of the
product components that your
ngers do not get pinched when
positioning components and
tightening xings.
• During product assembly and
adjustment, the carer should
avoid nger pinching risk of the
product’s joints or pivots.
• During transfers and adjustments,
the carer should avoid the nger
nipping risk of buckles.
Caution Daily Checks:
• The product is to be checked
daily before use to ensure that
all components are securely
attached and safe for use.
Caution Cleaning:
• Clean the product regularly
to prevent the build-up of dirt.
Accumulated dirt can prematurely

p6 GoTo Seat User Manual
English
SECTION 05: Safety Information
1. Always read user instructions
fully before use.
2. Users should not be left unattended
at any time in this product.
3. Always assess chair/trolley/pushchair
for suitability and stability before
attaching GoTo Seat.
4. Always ensure the GoTo Seat is rmly
secured before use and the straps
are tight.
5. The GoTo Seat has not been crash
tested and therefore cannot be used
in transport. Some airlines have
however approved GoTo Seat for use.
Check before you y.
6. Never use the GoTo Seat in a
shopping trolley on a sloping surface
greater than 10°, to avoid any risk of
falling over.
7. Attach Floorsitter rst and adjust
to preferred angle before placing
child in GoTo Seat.
8. Floorsitter should only be used
on a rm, solid at surface.
9. The GoTo Seat contains parts
which could present a choking or
tightening hazard to small children.
Check all components are securely in
place and securely fastened before
use – including knobs
and straps.
10. Do not modify the GoTo Seat.
Failure to follow the instructions
may put the child at risk. You
may also invalidate the GoTo Seat
warranty.
The warranty for GoTo Seat applies only
when the product is used according
to its intended use, following all
manufacturer’s specications.
A one year warranty is provided
with this James Leckey Design Ltd.
manufactured product.
Goods can be returned to us for
warranty, repair or replacement up
to 12 months from receipt. Once you
contact us, we will arrange collection
of the goods at our expense and, once
returned to us we will repair or replace
goods and return them to you within 14
days. In all cases, it is the customers’
responsibility to ensure the goods
being returned are suitably packaged,
preferably in the original packaging.
SECTION 04: Terms of Warranty

GoTo Seat User Manual p7
English
11. The GoTo Seat should be stored
carefully and should not be used if
any parts are faulty. The GoTo Seat
should be stored at to
prevent damage.
12. The GoTo Seat should be kept away
from all direct sources of heat
including naked ames, cigarettes,
electric and gas heaters.
13. If in any doubt about the safe use
of the GoTo Seat or if any parts
should fail, please cease using
the product and contact
Firey by Leckey Customer
Services on customer.enquiries@
reyfriends.com.
SECTION 06: Medical Device Combinations
It may be possible to combine the GoTo Seat with one or more other Medical
Device or other product. Information on which combinations are possible can
be found at leckey.com. All combinations listed have been validated to meet the
General Safety and Performance Requirements, section 14.1 of the Medical Device
Regulation 2017/745.
Guidance on the combination, such as mounting, can be found at leckey.com

p8 GoTo Seat User Manual
English
Precautions:
• Fixed spinal deformities such as
scoliosis or kyphosis
• Severe muscle contractures
• Severe muscular or skeletal
asymmetry including hip
dislocation
• Progressive and muscle wasting
conditions
• High risk or recent history of bone
fractures
• High risk of pressure related injury
or open sores
• Strong, uncontrolled movement
patterns
• Poorly controlled seizure activity
• Children dependent on the use
of percutaneous endoscopic
gastrostomy
• Medical instability including
compromised respiratory or
cardiovascular function
• Dependant on 3rd party life-
sustaining apparatus such as
oxygen tanks
• Signicant learning disabilities and/
or behavioural issues
Contraindictions:
There are no contraindications
associated with the use of the GoTo
Seat.
All precautions and contraindications
are taken at the discretion of the
prescribing clinician or parent. Leckey
and Firey recommends a trained and
experienced clinician to be present
during all initial assessment, set ups,
congurations and reissues in order to
minimise risk.
Section 07: Precautions and Contraindictions

GoTo Seat User Manual p9
English
SECTION 08: Cleaning and Care Information
Plastic Seat Base
1. When cleaning the plastic seat base
we recommend that you use only
warm water and a non-abrasive
detergent such as washing up liquid.
2. Disinfectant alcohols such as ethanol
and isopropanol are suitable for use
on the plastic body.
3. Never use organic solvents
or dry cleaning uids.
Upholstery and Fabrics
1. Clean and care for your fabric on a
regular basis. Simply vacuum with
an upholstery attachment to remove
dust particles and wipe with a damp
cloth for general cleaning.
2. Microbre cloths are extremely
effective without soap which is
helpful, as soap can clog your fabric.
3. The seat covers can be removed
from the hard plastic seat base
and machine washed at 40°C.
4. Drying procedure is to dry at.
Do not tumble dry.
5. Upholstery can be placed into the
washing machine intact, after
removing straps, buckles and
fastenings. Store these in a safe
place and out of reach of children.
6. Fabric can also be cleaned by hand
whilst in place. For solid food spills,
scoop up with a spatula. Clean the
fabric with a water-based product
such as foam from a mild detergent
and remove with absorbent cloth,
towels or sponge.
7. To successfully clean upholstery
without over-wetting the fabric or
causing colours to bleed, products
and tools specically designed to
care for upholstery must be used.
8. Clean spills right away. The longer a
spot or spill goes untreated, the more
difcult it is to remove. It can also
lead to permanent colour loss.
9. Routine soap and warm water
sponging is effective for ordinary
soiling and minor spills. Avoid rubbing
as it can be abrasive and damage
the fabric. Be careful not to saturate
the fabric as this will cause the stain
to spread. Work your way from the
outside in to avoid spreading the
stain more.
10. Antiseptic cleaning agents can
be used on more stubborn stains.
Disinfectant cleaning liquids such
as Isopropyl Alcohol or ethanol are
suitable for use on GoTo Seat. Ensure
that cleaning products are fully
removed.Please allow the product
to air dry, ensuring all alcohol is
evaporated before use.
For GoTo Seat Vinyl Cleaning and Care Information please refer to
page 30.

p10 GoTo Seat User Manual
English
11. Do not put the upholstery on to
the plastic base whilst the cover
is still wet. Dry thoroughly prior
to reassembly.
12. Do not iron the cover or straps.
13. Do not bleach any part of the GoTo
Seat.
Tip:
One of the best water-based upholstery
cleaners is very easy to make at home.
Put one cup of warm (not hot) water
into a mixing bowl and then add 1/4 cup
of biodegradable dish washing soap.
Beat with an electric mixer at medium
speed until the liquid becomes a thick
foam. This foam will remove built up
dirt and most food or drink stains.
Not only is this cleaner, simple to
make and inexpensive, it is also
nontoxic and environmentally-friendly.
Floorsitter base unit
1. Ensure the bottom of the oorsitter
base unit is cleaned after every use.
2. Soap and water can be used for
daily cleaning.
3. Do not use solvent to clean the
oorsitter base unit.
4. To remove sand/soil/grass or any
small particles that may be in the
oorsitter-to-seat connections,
slight tapping of the area will
encourage the particles fall out.
Rinse thoroughly to ensure there is
no build up of particles inside the
connections. For stubborn blockages
on the oorsitter, the latch can be
given a thumb push to remove any
particles and aid release.
5. Should your oorsitter come into
contact with salt water, rinse all parts
thoroughly with fresh, salt water.
If your oorsitter is being
used in environments
outside the home, (such
as the beach or garden)
it is important to rinse it
after every use so that it
is free from any particles/
obstructions that could
affect its working
mechanisms.

GoTo Seat User Manual p11
English
SECTION 09:
Product Servicing
For all service related issues
please refer to the rey website
www.reyfriends.com or contact
the Firey Customer Service team on
customer.enquiries@reyfriends.com
SECTION 10:
Important guidelines
Placing of child into GoTo Seat
1. The GoTo Seat must be securely
fastened in place for its intended use
before placing a child into the seat.
2. Floorsitter should only be used on a
rm, solid at surface. Soft surfaces
such as carpet and rugs (especially
deep pile) can reduce the stability of
the Floorsitter and should be used
with caution.
3. Ensure the harness straps do not
obstruct placement of child into the
GoTo Seat. Shoulder straps and side
lateral support straps should be
very slack.
4. If placed in a trolley: guide the child’s
legs slowly / gently through leg gaps
in shopping trolley; do not force
legs through.
5. Once legs are safely through, gently
t child’s arms through shoulder
straps – the shoulder straps should
be very slack. Ensure shoulder strap
pads are on child’s shoulders.
6. Close centre buckle and adjust side
lateral support straps to ensure
child is secure in seat harness.
The shoulder strap length should be
adjusted to t your child securely.
See Section 14(b) for guidance.
7. The groin strap length can
be adjusted by accessing the
adjustment tting underneath the
padded cover. In the GoTo Seat Size
2 the location of the groin strap can
be moved outwards to provide more
room for your child as they grow.
See Section 14(b) for guidance.
Removal of child from GoTo Seat
1. Slacken shoulder straps and side
lateral support straps.
2. Unlock central buckle using release
button on harness.
3. Slide shoulder straps off child’s
shoulders and gently remove
child’s arms from harness.
4. For Size 1 only, if placed in a trolley:
lift child up gently guiding their legs
out from the leg gaps in the trolley.
Do not attempt to lift child out of the
trolley while they are still attached to
the seat.

p12 GoTo Seat User Manual
English
SECTION 11: Product
Inspection
We recommend that various checks
of the equipment are carried out
before each use to ensure the product
is safe.
The recommended checks are
detailed below.
1. Check harness is in place and secure.
2. Check all upholstery for signs of
wear and tear.
3. Check all buckles to ensure straps are
secured rmly to the plastic body.
4. Check plastic support for cracks
or damage.
5. Ensure all knobs are tightened
securely.
6. Ensure GoTo Seat is secure on base
before positioning child in GoTo Seat.
7. If you are using the oorsitter,
please ensure it is securely
attached to the GoTo Seat.
See Section 13 for guidelines.
8. If you are using the oorsitter,
check latches and connections are
clear of dirt and debris with no signs
of wear and tear.
If in any doubt about the continued
safe use of your Firey product or if
any parts should fail, please cease
using the product and contact our
customer services department as
soon as possible.

GoTo Seat User Manual p13
English
SECTION 12: Reissuing
Firefly Products
Before re-issuing a product, it is
recommended that it is disinfected
using one of the following procedures:
Note: Always clean the product rst
to remove accumulated soiling prior to
disinfecting/sanitising.
1. Where possible, we recommend
the use of an automated “fogger”
disinfection system that is used
to completely cover the product
surfaces with a disinfectant agent.
The manufacturer’s instructions
for the chosen system should
be referred to prior to use and
followed exactly.
2. Where an automated disinfection
system is not available, all product
surfaces should be wiped over
with disinfectant surface wipes or
liquid disinfectant on a soft cloth.
Suitable products are 70% IPA,
70% Alcohol or diluted bleach. The
manufacturer’s instructions for the
chosen product should be followed.
Product upholstery and fabrics
should be cleaned thoroughly in
accordance with section, Cleaning
and Care Information, of this
manual.
Ensure a copy of the user manual is
supplied with the product. If in any
doubt about the continued safe use of
your Firey by Leckey product or if any
parts should fail, please cease using
the product and contact our customer
service department as soon as
possible on:
customer.enquiries@reyfriends.com.

p14 GoTo Seat User Manual
English
SECTION 13: Setting up your GoTo Seat
13(a) Aligning the lateral support
1
1
2
2
3
3
4
4
Your GoTo Seat will arrive like this,
with the lateral support aligned
to the body.
Loosen the knob just enough
so that you can rotate the
lateral support.
Rotate the lateral support
anticlockwise and into position.
Check that the lateral support is
home in the central section of
the backrest, and tighten
the knob.
Turn your GoTo Seat over and clip
the lateral support straps into the
central buckle. See Section 14(b)
for guidance.
Check that when the lateral
support straps are clipped
together, all straps are
arranged correctly as shown.
5
5

GoTo Seat User Manual p15
English
13(b) Setting up the Floorsitter
(if purchased with GoTo Seat)
The oorsitter should always be
placed on a rm, solid, static surface.
When placing the oorsitter on your
chosen surface, it’s vital that all
rubber feet are in contact with
the surface.
Once the oorsitter is in place,
ensure the recline arm is set to
its highest position.

p16 GoTo Seat User Manual
English
SECTION 14: Using the GoTo Seat
on a hardback chair
14(a) Attaching GoTo Seat to a hardback chair
1
A
B
C
2
1
2
Make sure all straps are loose and not
fastened to each other. Place GoTo Seat
on
to the hardback chair.
Fasten straps A together securely
around the back of the chair. Repeat for
straps B. Fasten straps Cunderneath
the chair.

GoTo Seat User Manual p17
English
34
5
Pull straps outwards
to tighten.
Tidy excess straps into
loops and secure into clips.
Ensure all black straps are securely
fastened to the hard back seat and
the ve-point buckle at the front is
unfastened before placing the child
in the GoTo Seat.

p18 GoTo Seat User Manual
English
14(b) Opening and closing the 5 point buckle
1
2
3
Before beginning, ensure
shoulder, lateral support
and groin straps are all
loose and unfastened.
Attach the two lateral support
fastenings to the sides of the
mid-point buckle.
Once fastened, adjust the
shoulder straps, lateral support
straps and groin strap by
pulling the straps to tighten.
In Size 2 GoTo Seat the groin
strap mounting location can be
moved backwards or forwards
to suit your child’s needs.
Ensure it is rmly tted to
the plastic GoTo Seat base.
1
2
2 2
Make sure the
straps are not
twisted when the
buckle is closed.
Smaller child Larger child

GoTo Seat User Manual p19
English
14(c) Adjusting the headrest and lateral support
1Unscrew the knob at the
headrest anti-clockwise to
remove the headrest from
the GoTo Seat base. Move
the headrest up or down to
achieve your desired position.
Once you have the headrest at
your desired height, screw the
knob back in to the GoTo Seat
base by turning clockwise.
Detach the lateral support by
turning the knob anti-clockwise.
Move the lateral support up or
down to achieve your desired
position. Once you have the
lateral at your desired height,
secure the lateral again by
turning the knob clockwise.
2
3 3
3
1
1

p20 GoTo Seat User Manual
English
SECTION 15: Using the GoTo Seat
on a supermarket trolley
Ensure all straps are loose and
unfastened. Place GoTo Seat in
to trolley seat. Thread straps A
through the grid of the trolley
seat and fasten. Pull straps to
tighten straps.
Thread straps Bthrough the
loop of the trolley seat, connect
and tighten where required.
Fasten straps C underneath
the trolley seat and pull to
tighten. Loop the straps and
tidy in to clips.
Ensure the trolley seat is secure
with the ve point buckle at
the front open and straps loose
before placing the child into
the trolley seat.
1
3
4
2
A
C
If there is no loop
at top of trolley
seat, attach straps
B to the same
frame as straps A.
B