Romina 2501 CONVERTIBLE CRIB User manual

ASSEMBLY INSTRUCTIONS
FOR YOUR
2501 CONVERTIBLE CRIB
20 Corporation Row, Edison, NJ 08817
Phone [phone], Fax [phone]
www.rominafurniture.com
Furniture
this picture shows how your crib
should look like after completing assembly
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISSION
IMPORTANT: PLEASE, READ ALL
INSTRUCTIONS BEFORE
ASSEMBLING! PLEASE, SAVE
INSTRUCTIONS FOR FUTURE USE
WARNING: THE PROPER USE OF THIS CRIB IS IMPORTANT FOR
YOUR BABY'S SAFETY. TO KEEP YOUR BABY SECURE AND SAFE,
AND TO AVOID POTENTIAL INJURY OR DEATH, CAREFULLY READ
AND FAMILIARIZE YOURSELF WITH ALL WARNINGS, CAUTIONS AND
INSTRUCTIONS IN THE INSTRUCTION BOOKLET. KEEP THIS
INSTRUCTION BOOKLET FOR FUTURE USE.
* READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
* NEVER USE PLASTIC SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS COVERS BECAUSE
T H E Y C A N C A U S E S U F F O C A T I O N .
* INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB
SIDES AND A MATTRESS THAT IS TOO SMALL.
NOTE: THE STYLE OF
Y O U R C R I B ,
MATTRESS SUPPORT
OR TODDLER RAIL
M A Y VA R Y F R O M
WHAT IS PICTURED IN
TH E INS TRU CTION
S H E E T

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH
OR REGULAR BED.
*USE OF A VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELL AND FINISH TO
PEEL. *DO NOT STORE CRIB IN AREAS WHERE TEMPERATURES AND CONDITIONS ARE EXTREME,
SUCH AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS
MAY CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN
STRUCTURAL FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE
MANUFACTURER WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR
CLEANING WITH MILD SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN
A DRY CLOTH, WILL PRESERVE THE ORIGINAL LUSTER AND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OF A CRIB WATER
MATTRESS. *LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN
THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT
ALL BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST
CHECK ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS
NECESSARY. PERIODICALLY INSPECT CRIB FOR DAMAGED
HARDWARE, LOOSE JOINTS OR SPLINTERED EDGES.
DO NOT USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR ROMINA FURNITURE FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE
TO HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU
MAKE CONTACT. THE MODEL CODE CAN BE FOUND ON A
WHITE LABEL LOCATED ON THE INSIDE OF YOUR CRIB ON
THE SIDE PANEL.
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO
YOUR CRIB!

2501 BOX CONTENT Please locate and confirm that
you have the following parts:
HB. headboard = 1
FB. footboard = 1
LP. left panel = 1
RP. right panel = 1
MS. mattress support = 1
WR. wooden rail = 1
WB. wooden block = 2
one bag of hardware with the following:
1. Allen wrench = 1
2. one storage pouch and two plastic ties
3. Allen bolt (60mm - 2 3/8") = 4
4. rounded head bolt (30mm - 1 3/16") = 4
5. rounded head bolt (15mm - 19/32") = 4
6. "butterfly" type nut = 4
7. bigger “internal star” lock washer = 8
8. smaller “external star” lock washer = 8
9. screw-in dowel = 2
10. cam fitting = 2
11. wood screw (30mm - 1 3/16”) = 3
12. Allen bolt (70mm - 2 3/4") = 4
Required tools: Allen wrench (supplied), Phillips screwdriver (not
included), flat screwdriver (not included).
CAUTION: Do not use a power screwdriver which can cause
screws to break or strip
Note: During the assembly process whenever using screws or
bolts, check each by placing the screw / bolt on the hardware
diagram which is drawn in actual size. Be sure to use the proper
size and shape specified in the instructions. Be sure to
COMPLETELY TIGHTEN the screws / bolts when you are asked
to do this.
Note: The letters which
identifies a part are the
initials of the respective
part name (such method
is employed to facilitate
parts recognition
between the drawings
and the parts list).
Phillips screwdriver (not included)
printed in full size
3
4
5
6
8
7
1
Note: The item number of your product
is located on the inner side of the left
panel, on a black and white label.
Please, refer to this number in the event
that you need to call ROMINA
FURNITURE or your local distributor.
Thank you.
9
10
11
9
10
HB
FB
RP
MS
WB
WR
LP
12

FIGURE 1
STEP 1 (Two adults are required to complete this step)
Attach the left and right panels (LP) & (RP) to the headboard
(HB), using 4 Allen bolts (12), 4 bigger washers (7) and the
Allen wrench supplied (1).
Do not completely tighten the bolts at this step, you will be
asked to do this later.
12 x 4 7x 4
12+7
HB
LP
RP
REQUIRED
12+7
12+7
12+7

3+7
3+7
3+7
3+7
RP
LP
HB
FB
FIGURE 2 3x 4
7x 4
REQUIRED
STEP 2 (Two adults are required to complete this step)
Attach the footboard (FB) to the left and right panels (LP) &
(RP) as they resulted after completing STEP 1 using 4 Allen
bolts (3), 4 bigger washers (7) and the Allen wrench supplied
(1).
Now, you must completely tighten all 8 Allen bolts (3+7) &
(12+7) remained not tightened from STEPS 1 & 2.
REMINDER
You have a total of 8 Allen bolts, distributed as following:
- 4 bolts (12+7) in the headboard (HB);
- 4 bolts (3+7) in the footboard (FB).
WARNING: TO KEEP YOUR BABY
SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S
V E R Y I M P O R T A N T T O
COMPLETELY TIGHTEN ALL 8 BOLTS
LISTED IN STEP 2.
WARNING!
COMPLETELY TIGHTEN!
WARNING!
COMPLETELY TIGHTEN!

LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
LOWEST POSITION
MIDDLE POSITION
HIGHEST POSITION
STEP 3
Assemble the mattress support using 4 bigger
round head bolts (4), 4 "butterfly" type nuts (6), 4
smaller lock washers (8) and a Phillips screwdriver
(not supplied). The lock washer must be attached
to the bolt after the bolt passed through the frame
and the metallic bracket of the mattress support
and before attaching the nut.
There are three positions for the mattress support
(from the highest one for a newborn to the lowest
one for a child that is maximum 35" tall - see
caution note). You must adjust the height of the
mattress support depending of your child height by
inserting all the four bolts in the same position
(see FIGURE 3).
Do not completely tighten the bolts at
this step, you will be asked to do this later.
NOTE: THE STYLE OF YOUR CRIB OR
OF YOUR MATTRESS SUPPORT MAY
VARY FROM WHAT IS PICTURED IN
T H E I N S T R U C T I O N S H E E T
FIGURE 3
A D J U S T I N G T H E H E I G H T O F Y O U R M A T T R E S S S U P P O R T
To adjust the vertical position of your mattress support you must remove all four bolts & nuts (4+8+6), loosen
all four bolts (5+8), lower the frame and insert the bolts (4) back into the corresponding holes, according to the
desired height (see FIGURE 3). Then, you must attach the lock washers (8) and the nuts (6) as described in
STEP 3 and completely tighten all the bolts.
Your crib is designed in such a manner that, when the mattress support is adjusted to it’s lowest
position, the mattress support frame must be placed directly over the inner wooden blocks. Before
tightening the bolts, you must slightly press the mattress support frame to make sure this position is
achieved.
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID POTENTIAL INJURY OR
DEATH, IT'S VERY IMPORTANT TO COMPLETELY TIGHTEN ALL 8 BOLTS (4+8+6) &
(5+8) AFTER YOU HAVE ADJUSTED THE HEIGHT OF YOUR MATTRESS
SUPPORT.
REQUIRED
4+8+6
4+8+6
4+8+6
4+8+6
4+8+6

REQUIRED
WARNING: TO KEEP YOUR BABY SECURE AND SAFE, AND TO AVOID
POTENTIAL INJURY OR DEATH, IT'S VERY IMPORTANT TO
COMPLETELY TIGHTEN ALL 8 BOLTS LISTED IN STEP 4.
FIGURE 4
STEP 4 (Two adults are required to complete
this step)
Turn your crib with the headboard on the floor, taking
care not to scratch its finish.
Attach the mattress support (MS) to the inner wooden
blocks using 4 smaller rounded head bolts (5), 4
smaller washers (8) and a Phillips screwdriver (not
supplied). The lock washer must be attached to the
bolt before inserting the bolt through the metallic
bracket of the mattress support.
Now, you must completely tighten all 8 bolts
(4+8+6, 5+8) involved in mattress support fixing
using a Phillips screwdriver (not supplied).
REMINDER
You have a total of 8 bolts, distributed as following:
- 4 bigger rounded head bolts (4+8+6) in the mattress
support (MS);
- 4 smaller rounded head bolts (5+8) in the wooden
blocks;
STEP 5 (Two adults are required to complete
this step)
Turn your crib with its feet back on the floor.
Attach the storage pouch supplied to the mattress
support spring using two plastic ties (also supplied).
Store this instruction booklet in the storage pouch for
future use.
After completing assembly, your crib should look like
the one depicted on the first page of this manual
MS
5x 4 8x 4
5+8
5+8
5+8
5+8
WARNING!
COMPLETELY TIGHTEN!

ASSEMBLY INSTRUCTIONS
FOR DAYBED OPTION
OF YOUR 2501
CONVERTIBLE CRIB
WARNING (FOR DAY BED OPTION ONLY):
ANY MATTRESS USED IN THIS CRIB MUST BE AT
LEAST 27 1/4 INCHES BY 51 5/8 INCHES WITH A
THICKNESS NOT EXCEEDING 6 INCHES.
THE MINIMUM AGE SHALL NOT BE LESS THAN 15
MONTHS AND THE MAXIMUM WEIGHT SHALL NOT
BE GREATER THAN 50LB.
IMPORTANT:
PLEASE, READ ALL INSTRUCTIONS
BEFORE ASSEMBLING!
PLEASE, SAVE INSTRUCTIONS FOR
FUTURE USE
DO NOT THROW THIS INSTRUCTION BOOKLET.
20 Corporation Row, Edison, NJ 08817
Phone [phone], Fax [phone]
www.rominafurniture.com
Furniture
this picture shows how your daybed
should look like after completing assembly

STEP A (Two adults are required to complete this step)
Remove the mattress support of your crib (see STEP 4 for details).
Remove the footboard of your crib (see STEP 2 for details).
Take the footboard of your crib and carefully hold it in vertical position, with its
feet on the floor.
Using the supplied Allen wrench (1) completely unscrew both Allen bolts and
washers (A) (previously mounted in factory) then remove the top rail.
You will find another factory mounted Allen bolts and washers (B), one for each
leg of your footboard. Remove the two smaller Allen bolts (B) and then the inner
frame footboard resulted by pulling it upward (see FIGURE A). Please, store
the resulted top rail, inner panel and Allen bolts in a proper place, taking care not
to scratch the wood finish.
B
A
A
B
inner frame
footboard
top rail
REQUIRED
FIGURE A

STEP B (Two adults are required to complete this step)
Using a Phillips screwdriver (not supplied) or just the hand, insert two screw-in dowels (9) into the metallic inserts holes found into each leg’s top (please
see the assembly tip for dowel correct positioning).
Insert two cam fittings (10) into the bigger holes found into the wooden blocks (WB), taking care that the little arrow of the cam is pointing downwards, to
the drilled face of the wooden block.
Using the factory installed wooden dowels, align the wooden blocks and attach them to the legs.
Then using the supplied Allen wrench (1) and moderate force, slightly rotate every cam fitting (10) clockwise (see the cam’s rounded arrow) by about 90
deg to 120 deg until become tight. Don’t over-tight the cams! This is not a fixture involved in your child safety.
Take the supplied wooden rail (WR) and attach it to your footboard using a Phillips screwdriver (not supplied) and three wood screws (11).
little
arrow
r
o
u
n
d
e
d
a
r
r
o
w
0+
-
assembly tip
WR
WB
9
10
11
11
11
9
10
WB
FIGURE B
9x 2
10 x 2
REQUIRED
11 x 3

STEP C (Two adults are required to complete this step)
Take the footboard of your crib (FB) as resulted after completing STEP B and attach it to the rest of the crib (see STEP 2 for details).
Do not completely tighten the bolts at this step, you will be asked to do this later.
STEP D
Take the mattress support (MS) and adjust it to its lowest position (see STEP 3 for details) then attach it to your crib (see STEP 4 for details).
Now, you must completely tighten all 8 bolts (4+8+6, 5+8) involved in mattress support fixing using a Phillips screwdriver (not supplied) and all 4 Allen bolts (3+7) remains not
tightened from all previous steps.
REMINDER
You have to tighten a total of 12 bolts, distributed as following:
- 4 Allen bolts (3+7) in the footboard (FB);
- 4 smaller rounded head bolts (5+8) in the lower part of the mattress support (MS);
- 4 bigger rounded head bolts (4+8+6) in the mattress support (MS).
STEP E (Two adults are required to complete this step)
Turn the resulted daybed with its feet back on the floor.
After completing assembly, your daybed should look like the one depicted on the first page of this section.

TODDLER RAIL OPTION OF
YOUR 2501 CONVERTIBLE CRIB
(THE TODDLER RAIL IS SOLD SEPARATELY)
NOTE: YOU CAN ATTACH A TODDLER RAIL TO
YOUR CRIB WITH THE PURCHASE OF ROMINA
FURNITURE ITEM TR 2501 (TODDLER RAIL 2501).
ASSEMBLY INSTRUCTIONS FOR TODDLER RAIL
CAN BE FOUND INSIDE OF TR 2501 PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR
LOCAL DISTRIBUTOR FOR MORE INFORMATION.

FULL SIZE BED OPTION OF
YOUR 2501 CONVERTIBLE CRIB
(THE CONVERSION KIT IS SOLD SEPARATELY)
NOTE: YOUR 2501 CONVERTIBLE CRIB CAN CONVERT INTO A FULL SIZE
BED WITH THE PURCHASE OF ROMINA FURNITURE ITEM CODE CKC
2501 (CONVERSION KIT FOR CRIBS, code 2501).
ASSEMBLY INSTRUCTIONS FOR FULL SIZE BED OPTION CAN BE FOUND
INSIDE OF CKC PACKAGE.
PLEASE, CONTACT ROMINA FURNITURE OR YOUR LOCAL
DISTRIBUTOR FOR MORE INFORMATION.

GENERAL FURNITURE CARE TIPS
· Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina Furniture item as beautiful and unique as you and your baby are. · To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
· Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
· Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be moved/rotated to prevent discoloration in the finish.
· Exposure to extreme variations of environmental conditions such as humidity and temperature can
affect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
· Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
· Wipe up spills promptly. If water or other liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
· In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
a quality defect.
· To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
· If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
· When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing pad's position frequently to avoid finish discoloration.

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of the
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.
Team
Thank you for being one of our distinguished clients.
Furniture