Firegear PRO Series User manual

Pro Series Fire Pit Burners with
All Weather Electronic Ignition System (AWS)
Installation and Operating Instructions
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS
DO NOT ATTEMPT TO INSTALL OR OPERATE THIS APPLIANCE
DO NOT DISCARD. THIS MANUAL
HAS IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS.
LEAVE WITH THE HOMEOWNER.
Warning: For Outdoor Use Only
INSTALLATION PRECAUTION:
This system requires a minimum 18-square inches (per side) of cross ventilation.
Failure to provide proper ventilation will void the warranty.
Natural Gas Models Propane Gas Models Description
FPB-26DPSBR21AWS-N FPB-26DPSBR21AWS-P 26” Round Disc with 21” Pro Brass Burner
FPB-29DPSBR21AWS-N FPB-29DPSBR21AWS-P 29” Round Disc with 21” Pro Brass Burner
FPB-34DPSBR21AWS-N FPB-34DPSBR21AWS-P 34” Round Disc with 21” Pro Brass Burner
FPB-25SFPSBR21AWS-N FPB-25SFPSBR21AWS-P 25” Square Disc with 21” Pro Brass Burner
FPB-30SFPSBR21AWS-N FPB-30SFPSBR21AWS-P 30” Square Disc with 21” Pro Brass Burner
FPB-34SFPSBR21AWS-N FPB-34SFPSBR21AWS-P 34” Square Disc with 21” Pro Brass Burner
Round Disc
MODEL:
SERIAL #:
PN#90191
Square Disc
“PRO SERIES”

FPB Pro Series Fire Pits with AWS System REV. A Page 2
CALIFORNIA PROPOSITION 65
WARNING
This product is designed to operate with one of the following fuel sources: Liquid Propane or Natural Gas. The fuel used to
operate this product, and the products of combustion of such fuel, can expose you to chemicals including Benzene which is known to
the State of California to cause cancer, birth defects and other reproductive harm and Carbon Monoxide which is known to the State
of California to cause birth defects or other reproductive harm.
(For more information go to: www.p65Warnings.ca.gov.)
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide
which has no odor.
Using it in an enclosed area can kill you.
Never use this appliance in an enclosed
space such as a camper, tent, car or home.
If you smell gas:
1. Shut off gas to the appliance
2. Extinguish any open ame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or re department.
DANGER WARNING
Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or other appliances.
Any LP cylinder not connected for use
shall not be stored in the vicinity of this
or other appliances.
WARNING
Do not leave unattended during use.
Do not use for cooking.
Follow all gas leak procedures in this
manual prior to operation.
WARNING
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property damage.
Read the installation, operating and
maintenance instructions thoroughly
before installing or servicing this
equipment.
WARNING
If the information in these instructions is not followed exactly, a re or explosion
may result causing property damage, personal injury or death.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and liquids in the vicinity
of this or other appliances.

REV. A Page 3
FPB Pro Series Fire Pits with AWS System
All media (i.e. lava rock, lava stones, lava boulders and fire glass) has the potential of
thermal spalling. This is a process that may occur when media is wet and moisture gets
trapped inside of the material due to rapid temperature differences. When this happens
the media has the potential to crack or “pop” outside the fire feature.
WE HIGHLY RECOMMEND COVERING ALL FIRE FEATURES WHEN NOT IN USE
The use of a cover can lessen the impact of thermal spalling; however, heavy rains, high
humidity and the presence of moisture may still cause the media to pop.
ALWAYS USE CAUTION WHEN USING THE FIRE FEATURE
Extra caution should be taken when lighting a fire feature when heavy rains, high humidity
and moisture are present. Light the fire feature; leave the area allowing any moisture in
the media to dissipate. We strongly recommend that during this drying out time that you
monitor the fire feature from a distance. This drying out period should be no less than 30
minutes. Continue monitoring the flame from distance to ensure that all popping has
ceased before fully enjoying the fire.
CAUTION
TABLE OF CONTENTS
Specications 4
Preparing a Non Combustible Structure 5
Ventilation; Hard Piping 5
Gas Pipe Sizing Chart 6
Carton Contents - Single Fire Feature 7
Pre-Installation Check List for Single Installation 8
Power Supply Location for Single Installation 9
Burner Pan & Enclosure Preparation 10
Wiring Diagrams 10
Media Installation 11
Operating- Lighting Instructions 12
Replacements Parts 13
Replacement Parts List & Valve Reference 14
Trouble Shooting 15-17
Optional Accessories 18
Warranty 19
Congratulations! You have just purchased a Firegear Outdoors “Pro Series” re pit that includes
a 304 Stainless Steel burner pan with a Brass Burner. The Brass Burner comes in a 21-inch model.
Each burner leg incorporates individual injectors that take the place of a standard main burner orice.
Each burner is unique in the fact that the 21-inch burner has four (4) injectors per leg. These injectors
provide a unique ame pattern that differs from a typical steel burner.

FPB Pro Series Fire Pits with AWS System REV. A Page 4
SPECIFICATIONS
Table 1 Installation specications
Models:
N= Natural
P= Propane
Injector
Size
Btu’s
FPB-26DPSBR21AWS-N
FPB-26DPSBR21AWS-P
#61
(0.039)
175,000 Btu’s
(51.28kW)
FPB-29DPSBR21AWS-N
FPB-29DPSBR21AWS-P
#61
(0.039)
175,000 Btu’s
(51.28kW)
FPB-34DPSBR21AWS-N
FPB-34DPSBR21AWS-P
#61
(0.039)
175,000 Btu’s
(51.28kW)
FPB-25SFPSBR21AWS-N
FPB-25SFPSBR21AWS-P
#61
(0.039)
175,000 Btu’s
(51.28kW)
FPB-30SFPSBR21AWS-N
FPB-30SFPSBR21AWS-P
#61
(0.039)
175,000 Btu’s
(51.28kW)
FPB-34SFPSBR21AWS-N
FPB-34SFPSBR21AWS-P
#61
(0.039)
175,000 Btu’s
(51.28kW)
Table 2 Btu Specications for Pro Spur Burner.
Note: All injectors are the same size for entire burner.
Disclaimer: Btu listings are based on 7.0” WC for Natural
Gas and 11.0” WC for Liquid Propane (LP) at the burner
orice when using Firegear Outdoors Burning Spurs.
Note: Flex line size and proper gas pipe sizing will also
affect Btu’s. As a result your Btu’s may vary slightly from
Table 2 specications.
Fig. 2 Clearance to Combustibles
(Not to be used in an enclosed space)
Models:
Natural Gas
Models:
Propane Gas
A
Disc
Depth
B
Disc
Diameter
C
Burner
Size
Min.
Opening
D
Ground
Level
E
Side
Wall
F
Combustible
Ceiling
G
Combustible
Floor
FPB-26DPSBR21AWS-N FPB-26DPSBR21AWS-P 1/16” 26” Rd. 21” 24” 16” 36” 120” 18”
FPB-29DPSBR21AWS-N FPB-29DPSBR21AWS-P 1/16” 29” Rd. 21” 27” 16” 36” 120” 18”
FPB-34DPSBR21AWS-N FPB-34DPSBR21AWS-P 1/16” 34” Rd. 21” 32” 16” 36” 120” 18”
FPB-25SFPSBR21AWS-N FPB-25SFPSBR21AWS-P 1/16” 25” Sq. 21” 23” 16” 36” 120” 18”
FPB-30SFPSBR21AWS-N FPB-30SFPSBR21AWS-P 1/16” 30” Sq. 21” 28” 16” 36” 120” 18”
FPB-34SFPSBR21AWS-N FPB-34SFPSBR21AWS-P 1/16” 34” Sq. 21” 32” 16” 36” 120” 18”
F
E
G
C
L
24”
Max
Overhang
Fig. 1 Shows disc side view.
AB
D
Ground Level (Earth)
C
Valve
Box
Pressure NG LP
Min. Inlet 3.5” WC (⅛ PSI) 8.0” WC (¼ PSI)
Max. Inlet 14.0” WC (½ PSI) 14.0” WC (½ PSI)
Normal Inlet 7.0” WC (¼ PSI) 11.0” WC (⅜ PSI)
Table 3 Gas Pressures

REV. A Page 5
FPB Pro Series Fire Pits with AWS System
PREPARING A NON-COMBUSTIBLE STRUCTURE
IMPORTANT
Installation of Natural or LP gas should be done by a
qualied installer, service agency or gas supplier.
This appliance must be isolated from the gas supply
piping system by closing its manual shutoff valve during
any pressure testing of the gas supply piping system at
test pressures equal to or less than ½” psi (3.5kPa)
VENTILATION FOR NON-COMBUSTIBLE
ENCLOSURE
Fire features are subjected to many outdoor elements
such as rain, snow, wind, heat or cold. A minimum of 18
square inches (opposite sides) of cross ventilation is
required to keep the components in good working
order. Use Fig. 3 on as guide to assist to incorporate
proper ventilation.
HARD PIPING TO FIRE FEATURE WITHOUT
GAS PROXIMITY
NOTE: Refer to the NFPA54 (National Fuel Gas Code) for
proper pipe sizing. See gas line sizing chart on page 6 as
a reference.
1. Turn OFF gas supply system. NOTE: All gas
connections (except for brass to brass) require the
following. Clean pipe threads using either a wire brush
or steel wool. Apply pipe sealant to the ttings before
making any connection.
2. Ensure all gas connections are snug, but do not over
tighten! BE CAREFUL!
3. Install necessary pipe for the distance required and a
manual shut-off valve at the exterior house wall. Check
with local codes for proper procedures. If pipe is to
pass through a foundation or house wall, make sure
to seal the area around the pipe with weather sealant.
Consult a plumber for proper installation to ensure you
are providing adequate gas supply for your application.
4. The primary gas shut-off (not supplied) will require a ½”
male ared tting to enable connection of the stainless
steel ex gas line (not supplied) with the re feature.
5. Do not place an LP tank inside any re pit enclosure.
Locate all Liquid Propane (LP) tanks outside the
enclosure.
6. To prevent performance problems with LP gas re pits,
do not use a LP tank less than 100lbs. capacity.
DESCRIPTION This is a eld serviceable (30VDC)
commercial grade outdoor electronic system with a
maximum gas capacity of 290,000 Btu’s. The system
features a built-in safety shut-off in case of ame loss and
auto-relight. It is shipped as a Natural Gas (NG) model only
and must be converted if using Propane (LP) gas. This
system must be installed with a burner pan, burner and
orice and installed into an non-combustible enclosure.
The “All Weather System” (AWS) requires a 120VAC
Ground Fault Interrupter (GFI) to be installed in a
weatherproof box. A power supply must be selected for
each installation.
In the absence of local codes use the latest edition of the
National Fuel Gas Code NFPA54 and National Electrical
Code (NEC), or NFPA 70. The weatherproof box (supplied)
should be mounted securely within 2-feet or less of the GFI
box. The GFI box will provide the 120VAC for the power
supply.
READ THIS MANUAL COMPLETELY BEFORE
BEGINNING INSTALLATION. UNDERSTAND
HOW THEY OPERATE AND INSTALL.
Fire Pit
Enclousure
2”x3”
Fire Pit
Examples of Cross Ventilation
3 - 2”x3” Slots Per Side or
2- 1” x 9” Slots Per Side
Cross Flow Ventilation
(Min. 18 Sq. In. Per Side)
Fig. 3 Shows cross ventilation in a enclosure.
LEVEL FLAT SURFACE Install re feature on any
level, outdoor non-combustible, at stable surface or a
combustible oor according to the clearances specied in
this manual for a Firegear burner. NOTE: Depending on
venting locations, do not place re pit directly on grass,
dirt, or rocks that could prevent proper ventilation. Ensure
proper water drainage is also incorporated into the re
feature enclosure.

FPB Pro Series Fire Pits with AWS System REV. A Page 6
REFERENCE
GAS PIPE SIZING
Length of Pipe in Feet 1/2” 3/4” 1” 1 - 1/4” 1 - 1/2” 2” 2 - 2 1/2” 3” 4”
10 275 567 1071 2205 3307 6221 10140 17990 35710
20 189 393 732 1496 2299 4331 7046 12510 25520
30 152 315 590 1212 1858 3465 5695 10110 20620
40 129 267 504 1039 1559 2992 4778 8481 17300
50 114 237 448 913 1417 2646 4343 7708 15730
60 103 217 409 834 1275 2394 3908 6936 14150
70 89 185 346 724 1086 2047 3329 5908 12050
80 78 162 307 630 976 1811 2991 5309 10830
90 69 146 275 567 866 1606 2654 4711 9613
100 63 132 252 511 787 1496 2412 4281 8736
125 54 112 209 439 665 1282 2083 3618 7382
150 48 100 185 390 590 1138 1808 3210 6549
175 43 90 168 353 534 1030 1637 2905 5927
200 40 83 155 325 491 947 1505 2671 5450
300 37 77 144 303 458 887 1404 2492 5084
NATURAL GAS : PIPE SIZING CHART
•Natural Gas (NG) flow is given in
thousands of BTU/hr. = 1cubic
foot of NG gas - 1000 BTU
•Nominal pressure at the burner
for Natural Gas is 3.5” of water
column. (Typical machine supply
5”-7”)
•Pipe length must include
additional length for all fittings.
Add approximately 5 feet of pipe
per fitting.
•Natural Gas Example: A machine
with a burner that requires
440,000 BTU would need a 1 -1/4”
pipe for a 20” long run.
LIQUID PROPANE : PIPE SIZING CHART
NOTE: The sizing charts above list the specific pipe sizes required for the amount of BTU’s for a new gas line installations. If you
are using an existing gas line you must take into consideration the existing gas line capacities to ensure you will have proper
pressure. This chart is for reference only, we recommend you consult with a Licensed Plumber/Gas Fitter or NFPA54 (National Fuel
Gas Code - current edition) for more details.
Length of Pipe in Feet 1/2” 3/4” 1” 1 - 1/4” 1 - 1/2” 2” 2 - 2 1/2” 3” 4”
10 108 230 387 793 1237 2259 3640 6434 -
20 75 160 280 569 877 1610 2613 5236 9521
30 61 129 224 471 719 1335 2165 4107 7859
40 52 110 196 401 635 1143 1867 3258 6795
50 46 98 177 364 560 1041 1680 2936 6142
60 42 89 159 336 513 957 1559 2684 5647
70 38 82 149 317 476 896 1447 2492 5250
80 36 76 140 239 443 840 1353 2315 4900
90 33 71 133 275 420 793 1288 2203 4667
100 32 68 126 266 411 775 1246 2128 4518
125 28 60 117 243 369 700 1143 1904 4065
150 25 54 105 215 327 625 1008 1689 3645
175 23 50 93 196 303 583 993 1554 3370
200 22 47 84 182 280 541 877 1437 3160
300 17 37 70 145 224 439 686 1139 2539
•Liquid Propane (LP) Gas flow is
given in thousands of BTU/hr. =
1cubic foot of LP gas - 2500 BTU.
•This chart refers to low pressure LP,
after regulation, Standard nominal
pressure at the burner for Liquid
Propane Gas is 11” of water column.
•Pipe length must include additional
length for all fittings. Add
approximately 5 feet of pipe per
fitting.
•LP Example: A machine with a
burner that requires 440,000 BTU
would need a 1” pipefor a 20’ long
run.
GAS PIPE SIZING CHART
Table 4 Gas Pipe Sizing Chart

REV. A Page 7
FPB Pro Series Fire Pits with AWS System
GOE-30VDC Power Supply
AWS Disc Assembly
Carton Contents
Hardware
Bag
REMOVING FIRE PIT ASSEMBLY FROM CARTON
These re pit comes assembled and only requires a gas
connections after it is installed into the enclosure.
Open carton and remove contents. Inspect for any damage
or missing parts. The hardware bag includes the key valve
part shown below in Fig. 5.
Note: Check for any gas leaks after gas is connected and
turned ON.
Fig. 4 Shows carton contents. Note: Round pan was illustrated for this drawing.
CAUTION: Use dielectric grease on all wire nut
connections and ¼” connectors to prevent moisture issues
from the outdoor environment.
Hardware Bag
(included with re pit)
These re pits include a valve and control system that is
certied by Lab Test for USA and Canada to meet ANSI
Z21:.97-2014, CSA C22.2 No 3-M1998 (R2014)
Fig. 5 Hardware bag contents.
ON
OFF

FPB Pro Series Fire Pits with AWS System REV. A Page 8
PRE-INSTALLATON CHECK LIST FOR SINGLE INSTALL
GAS INFORMATION
Gas Volume - Ensure the correct size pipe is used for
the total gas load. If installing more than one re feature,
ensure the correct size pipe is based upon the distance of
the furthest re feature away and the total gas load is for
all gas appliances on that gas line (i.e. re feature, BBQ,
torches, etc.).
Gas Pressure & Type of Gas - What is the gas pressure
being supplied to the re features? Is the re feature(s)
congured for the proper gas type? The AWS gas valve is
shipped gas type specic.
Manual Shut-off/Key Valve - The manual key valve
(supplied) should be installed within 6-feet of the re
feature. Verify proper distance with local and national
codes.
Purging a New Gas Line - Has the gas line been purged
of both air and possible debris? Any gas lines buried
underground must be pressure tested up to 60PSI to
ensure no leaks. After inspection is complete, most
plumbers will release pressure in the line at one location by
opening the manual ball or key valve. It is recommended
to release pressure by opening a ball/key valve associated
with all the re features. Example: There are four re
features on a job, open the rst key valve for a few
seconds, then close it. Then move on to the next key valve
and do the same thing until you have purged the debris out
of all four gas lines.
Injectors/Jets - Fire features using a Firegear Pro Series
brass burner incorporates individual injectors/jets on each
burner leg. All injectors are protected by a injector cover
that is provided with each burner. The injector hole size is
measured by using a numbered drill bit. An injector/jet
limits the amount of gas ow to the burner to ensure the
ame is a safe and reasonable height to not pose a risk to
people or property. Note: The Firegear Pro Series brass
burners DO NOT USE a primary main burner orice like a
standard stainless steel burner. A steel nipple is installed in
place of the primary burner orice.
ELECTRICAL INFORMATION
Wire Gauge - Is the wire gauge correct? Wiring must be
12AWG or greater (solid or stranded) for all installations.
Note: It is recommended to ll the wire nuts with either
dielectric grease or silicone prior to installing the wire nut.
This will ensure a waterproof connection.
Why GFI circuit? A GFI is a type of circuit breaker which
shuts off electric power when it senses an imbalance
between the outgoing and incoming current. It protects the
house wires and receptacles from overheating and possible
re.
Power Supply - Firegear Outdoors offers one power
supply for use with the FPB re features. The power
supply requires 120VAC power to operate and converts it
to 30VDC to operate the gas valve. DO NOT CONNECT
120VAC DIRECTLY TO THE GAS VALVE WIRES -
DAMAGE WILL OCCUR. The GOE-30VDC is used for
one re feature only - installed 10-feet or greater from a
pool or spa. This power supply has a 3-foot power cord to
plug into 120VAC outlet and a 3-foot leads to connect to the
gas valve on the 30VDC side. Note: The FG-PS-30V320
power supply is optional and required for pool/spa
installations within 5-feet of re feature.
MEDIA INFORMATION
Acceptable media placed over top of the burner:
Lava Rock 1”- 2” size
FG-LAVA-10 (10 LB)
FG-LAVA-40 (1-Cubic Foot)
GL Glass ½” - ¾” size
Various colors are available
See Product catalog for details
GRL Reflective Glass ½” - ¾” size
Various colors are available
See Product catalog for details
DRAINAGE INFORMATION
For any fire feature ABOVE ground level requires a drain
line or a way for water to exit the fire feature.
NOTE: THIS AWS SYSTEM IS NOT APPROVED TO BE
INSTALLED BELOW GROUND LEVEL.
Fig. 6 Arrow shows one injector with brass cap/cover.

REV. A Page 9
FPB Pro Series Fire Pits with AWS System
PREPARING A NON-COMBUSTIBLE STRUCTURE FOR SINGLE INSTALL
POWER SUPPLY LOCATION
The GOE-30VDC power supply is to be installed inside the enclosure due to the wire length limitations. The power cord is
3-feet long the 30VDC leads to the valve are 3-feet long. See Fig. 5.
Fig. 7 Example of a single re feature install with power supply and switch contained within the enclosure, when
applicable. Note: Must be 10-feet or more from a pool/spa for this installation.
See additional illustration on page 10, Fig. 8.

FPB Pro Series Fire Pits with AWS System REV. A Page 10
INSTALLING BURNER PAN INTO ENCLOSURE
Fig. 8 Show typical wiring diagram with switch.
Timer
FG-1420-A OD
Remote Emergency
Stop
(Optional)
FG-PS-30V320
Low Voltage
Power Supply
Key Valve
Electrical Line
Gas Line
ON
OFF
or
Main Burner
Flat Pan
Pilot Burner
(Min. 12-gauge Max. 500’)
Flex Frame (shown in detail)
enables the ability to
remove the pan/disc
to service valve system
Flex
Frame
Optional ON/OFF
Controls
Note: Actual power supply must be
10-feet or more from the pool or spa
D
E
T
A
I
L
Pool
Control
Pool Certified Applications
(Fire Feature within 5-feet of pool or spa)
Pool
ON
OFF
ON
OFF
Key Valve
& Switch
Fig. 9 Shows any re feature installed within 5 feet of a pool or spa requires FG-PS-30V320 power supply (purchased
separately). DO NOT USE THE GOE-30VDC. FG-PS-30V320 power supply can be installed up to a maximum of
500-feet away from re pit.

REV. A Page 11
FPB Pro Series Fire Pits with AWS System
INSTALLATION OF MEDIA INTO BURNER PAN
Install lava rock into the burner pan. Ensure the lava rock is
a minimum of 1-inch diameter for proper operation.
Note: Do not pour Lava Rock directly from bag. It should
be placed naturally and NOT packed in tight. Loose tting
is important to ensure robust ames. Placing the lava rock
in the pan by hand, ensures no excessive dust from bag
lays in the bottom of pan and potentially plugs the burner
port holes or the pan weep holes. DO NOT BLOCK
INJECTORS WITH MEDIA.
IF USING FIREGEAR OUTDOORS GL GLASS OR GLR
REFLECTIVE GLASS, ENSURE THE MEDIA DOES NOT
BLOCK THE INJECTOR HOLES.
IMPORTANT: DO NOT PLACE ROCK OVER TOP OR
UNDER THE PILOT SCREEN COVER. The screen must
be free of any debris to ensure proper lighting of burner
and good ame sense (See Fig. 10).
Cover the burner completely with media but do not make
the depth greater than 1-inch over-top of the burner. Do
not block injectors with media.
Do NOT cover the top of mesh pilot hood with any rock or
glass. It must be free an any debris to operate properly.
Mesh Pilot Hood
Media
Fig. 10 Media placement around pilot hood.
Acceptable media to be placed over top of the burner:
Lava Rock Min.1”- 2” size
FG-LAVA-10 (10 LB)
FG-LAVA-40 (1 CUBIC FOOT)
GL Glass Min. ½” - ¾” size
Various colors are available
See Product catalog for details
Sold in 10LB jugs or 6 jugs to a case
GRL Reflective Glass
Min. ½” - ¾” size
Various colors are available
See Product catalog for details
Sold in 10LB jugs or 6 jugs to a case
FINAL PREPARATIONS
MEDIA INSTALLATION

FPB Pro Series Fire Pits with AWS System REV. A Page 12
CAUTION: Children and adults should be alerted to the hazards on high surface temperatures and should stay away to
avoid burns or clothing ignition. Young children should be carefully supervised when they are in the area of the appliance.
WARNING: Do not use this appliance if any part has been under water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of control system and any gas control, which has been under water.
OPERATION & LIGHTING
SAFETY WARNINGS
1. Never leave the re pit unattended during operation.
2. Clothing or other ammable materials should not be placed on or near the appliance.
3. Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the
appliance.
4. Installation and repair should be done by a qualied service person. The appliance should be inspected before
use and at least annually by a qualied service person. More frequent cleaning may be required as necessary. It
is imperative the control compartment, burners and circulating air passageways of the appliance be kept clean.
5. Inspect the fuel supply connection before each use of the appliance.
6. Temporary storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply
(Natural or LP gas line).
WARNING
1. This appliance is hot when operated and can cause severe burns if contacted.
2. Do not burn any solid fuels in this appliance.
READ ALL LIGHTING INSTRUCTIONS BEFORE ATTEMPTING TO LIGHT FIRE PIT
CAUTION: ENSURE YOU HAVE LEAK TESTED THE FIRE PIT BEFORE OPERATING.
WARNING: Do not stand over re pit during ignition or operation due to high surface temperatures.
LIGHTING INSTRUCTIONS
TURNING ON FIRE PIT/FEATURE
Prior to turning the re pit ON, visually inspect the re pit to ensure debris such as leaves or other combustible materials
have not collected on top of the re pit, which could burn and emit embers once the re pit is turned ON. At the same
time, ensure anyone standing close to the re pit is aware you are turning it ON and steps away, at a safe distance prior to
lighting.
The ignition sequence is as follows:
1. Turn the manual key valve to the ON position.
2. Turn the re pit ON by pressing the ON button of the switch. The hot surface igniter will heat up and begin to “glow”
in approximately 10 seconds.
3. Once the hot surface igniter heats up, the pilot gas valve opens, a “click” is heard, and gas is released to the burner,
lighting the re pit.
The entire ignition sequence ignites within 20 seconds or less. If not, press the OFF button of the switch and wait 5
minutes before trying again.
TURNING OFF FIRE PIT/FEATURE
1. Turn the re feature OFF by pressing the OFF button of the switch or timer if applicable.
2. If you are no longer burning the re pit until another time, we recommend turning the key valve to OFF position.

REV. A Page 13
FPB Pro Series Fire Pits with AWS System
AWS REPLACEMENT PARTS
GOE-30DCV
OUT
1
4
3
2
5
6
7
8
9
10
Items are not to scale

FPB Pro Series Fire Pits with AWS System REV. A Page 14
AWS REPLACEMENT PARTS LIST
1 Ignition Control Box (Valve box only) 1 FG-ICB
2 Pilot Burner Assembly (Complete pilot assembly and wires) 1 FG-PBA
330VDC Power Supply for single re feature (10-feet from pools) 1 GOE-30VDC
5 Primary Pilot Burner Gas Line (24-inch) 1 FG-PPBG
6 Secondary Pilot Burner Gas line (24-inch) 1 FG-SPBG
7 Pilot Burner Cage (hood) 1 FG-PBC
8 Thermopile - for primary pilot assembly 1 FG-TP
9 Hot Surface Ignition - for pilot burner assembly (item #2) 1 FG-HSI
10 Heat Shield 1 FG-HEATSHIELD
11 Rocker Switch (installs into 78130) (not shown) 1 WP-SWITCH
12 AWS Face Plate Assembly (not shown) 1 78130
13 ½” Flare x to ½” MIP (not shown) 1 U1-8D-S
14 21-inch Pro Series Brass Burner (not shown) 1 FG-PSBR-BS21
Item Description Part Number
Qty.
OUT
Valve Box Reference
2-pin Igniter Connector
2-pin Thermopile Connector
Flared Pilot Connection
Compression Pilot Connection

REV. A Page 15
FPB Pro Series Fire Pits with AWS System
TROUBLESHOOTING
Sequence of Operation
Fire Feature Turned ON
First Pilot with Hot Surface Igniter
Heats Up and Glows (Approx. 10 seconds)
Secondary Pilot Opens; “Click” is Heard;
Gas is Released to Burner
Fire Feature is Lit Until
Turned OFF
The system is designed to relight itself if blown out. It will try (3)
times to relight before it goes into a “hard” lock out.
Then it must be turned OFF and back ON to reset it .
• No Power - Check for power at the re feature(s). Conrm proper power is being supplied to the system. 30VDC
from power supply to valve and 120VAC where power supply is plugged into.
• Defective Controller - If for some reason someone connected 120VAC power directly to the gas valve, the controller
inside the valve box will be damaged. It this happens, a burned electrical smell might be present.
• Connector Not Plugged In Correctly - Check the 2-Pin connector from pilot to the gas valve, Ensure it is plugged
into place with the locking latch.
• Pins Not Secure - Check the pins inside the 2-pin connector, ensure they are not loose. If loose push them back in
until tight and try system again.
• Possible Defective Igniter - Unplug the igniter and check resistance across the two pins inside the plastic housing
coming from the pilot assembly. Use a multi-meter to check resistance. Resistance should be 2.0 - 4.5 ohms. If no
resistance or resistance greater than 8 ohms indicates a defective igniter.
1. Turned the Fire Feature ON... but nothing happens.
2. Glow Plug does not glow.
START UP ISSUES

FPB Pro Series Fire Pits with AWS System REV. A Page 16
• Insufcient Power - If the glow plug is not getting enough power, it will not ignite the gas.
• Thin Wire - The recommended minimum wire gauge is 12AWG . If wire is less than 12-gauge there may not be
enough power to get the igniter hot enough.
• No Gas - Was the gas line purged of air? If gas line was not bled it may take a while before the gas gets to the re
feature.
• Manual Shut Off Valve - Is the manual shut-off or key valve open?
• Debris - Debris can get trapped inside the screen of the gas valve. Excessive amounts of pipe dope or Teon tape
can restrict gas ow.
• Debris in Pilot Burner - New gas lines, until bled, have air and will have some debris. Ensure gas it turned OFF and
electrical is unplugged. Remove the two brass ttings from the gas valve, then use “canned air” to blow through the
pilot outlets.
• Wrong Pilot Orice - If the wrong pilot orice is installed into the primary pilot it will not light.
• Oxygen Starvation - To ignite gas we need oxygen, fuel and a heat source. If the pilot assembly is buried under-
neath the glass media or lava rock it will not allow the pilot to light.
• Weak Igniter - In some cases, the manufacturer’s glow plug will have slight difference in assembly which can cause
some igniter’s to burn hotter than others. These are tested before they are sent to customers but sometimes a weak
one can get out. If this occurs, the symptom will always be the same - inconsistent or no ignition at all. In this case,
replace the pilot burner.
• Valve Box Installed Backwards - Check the label on the gas valve box and ensure the burner is connected to the
OUTLET side of the gas valve box.
• Thermopile Pins Not Secure - Check the pins in the pilot burner connector, remove it from the gas valve and check
for loose pins. If loose, push inward until tight and try again. If this happens, the glow plug will stay ON for up to 30
seconds before turning OFF. It normally shuts off in about 5 seconds.
• Defective Thermopile - Thermopile’s rarely go bad however if a product is used consistently for extended periods
of time a thermopile can get too hot (like a blow torch) and eventually cause it to swell. Simply loosen the thermopile
from the pilot assembly and slide it out. If it will not slide out because is it too tight, then it will need to be replaced.
• Debris - Debris can get trapped inside the screen of the gas valve. Over time rust and other debris can restrict the
gas ow on the Outlet screen of the valve that can partially or sometimes even stop the ow. Inspect the screen,
remove it and clean it then replace it.
• Defective Controller or Main Gas Valve - If you have inspected the thermopile connections and no debris is on the
controller or gas valve; checked the power, then the gas valve or controller may be defective and will need replaced.
3. Glow Plug Glows, But Does Not Ignite the Gas
4. Pilot Lights, But No Flame to the Main Burner
5. Fire Feature Lights... Turns OFF Within A Few Seconds...
and Restarts Again (Keeps repeating this sequence)
• Gas Volume Insufcient - When initially turning ON the re feature pilot is lit and there is enough gas for the pilot to
light, however once main gas valve is turned ON, the ow of gas to pilot drops not providing enough gas to keep the
thermopile hot enough, therefore the pilot will drop out and relight. This is usually caused by insufcient Gas Volume
and can be caused by installing gas pipe too small to deliver proper amount of gas or by installing a Manual Gas
Shutoff (Ball valve or Key Valve) with a capacity that is too small to allow enough gas to pass through to the feature.
• Main Burner Orice Not Installed - Ensure the correct orice is being used. If using LP gas it should have vent
holes, Natural gas does not. The orice/air mixer restricts the amount of gas owing to the Main Burner. This restric-
tion ensures that not ALL the gas will ow to the Main Burner, so there is still enough gas left for Pilot Burner.
• Oxygen Starvation - to ignite gas, you need oxygen, fuel and a heat source. If the pilot assembly is buried under-
neath the glass media or lava rock it will not allow the pilot to light.
• Defective Thermopile - See Symptom 4 above for Defective Thermopile.
• Defective Controller – If your plumbing is supplying enough gas, the Main Burner orice is installed, the Pilot Burner
is getting plenty of air and the Thermopile is not defective the only thing left is a Defective Controller inside the valve
box. If you have a Defective Controller the only way to x it is to replace it.
TROUBLESHOOTING

REV. A Page 17
FPB Pro Series Fire Pits with AWS System
6. Fire Feature Cycles (Turns On and Off) Every Few Minutes
• Gas Volume Insufcient – See symptom 5 page 16 for “Gas Volume Insufcient” for detailed explanation.
• Oxygen Starvation (Pilot Burner) – See symptom 5 page 16 for “Oxygen Starvation” for detailed explanation.
• Defective Thermopile – See symptom 4 page 16 for “Defective Thermopile” for detailed explanation
• Defective Controller – See symptom 5 page 16 for “Defective Controller” for detailed explanation
7. Main Burner Flame Lazy/Small or Flame NOT Spread Out Over Entire Burner
• Gas Volume Insufcient – See symptom 5, page 21 for “Gas Volume Insufcient” for detailed explanation
• Debris On Inlet Screen; Valve Box – See symptom 3, symptom 4, page 16 for “Debris on inlet screen for detailed
explanation
• Debris On Outlet Screen; Valve Box – See symptom 4, page 16 for “Debris on Outlet Screen for detailed
explanation.
• Obstruction In Plumbing Between Gas Valve Outlet and Main Burner – If your plumbing was sized correctly to
deliver the proper amount of gas and the screens in the valve box are clean, inspect the plumbing between the valve
and the burner for obstructions. Also, inspect inside the burner inlet to ensure no obstructions in there as well.
8. Main Burner Flame “Flares Up” Every Few Minutes
• Fire glass/Media Layer too Thick – Fire glass/media comes in different sizes. Use only ½” - ¾” diameter. If you put
a thick layer of re glass/media on top the burner, over 1” in depth; there is a good chance some of the gas will get
“trapped” within the media while the feature is ON. When this happens, the trapped gas in the re feature ignites and
you see the “Flare Up” effect. Remove some of the re glass/media from the burner to see if this xes the problem.
• Gas Leak – Natural Gas is lighter than air therefore when released into the atmosphere it rises. If you have a Natural
Gas re feature and there is a gas leak the Natural Gas will rise to the top of the feature. Once it encounters the ame
a are up will occur. Propane is heavier than air so if there is a gas leak when using propane the gas will fall into the
bottom of the feature. That is why it is REQUIRED drainage/ventilation be installed at the bottom of the feature when
using Propane. You do NOT want Propane accumulating inside the re feature.
9. Turn the Feature OFF…but a Small Flame Continues to Burn in the Pilot Burner
• Leak in the Pilot Burner Gas Valve – When debris enters the gas valve by way of either the Inlet or outlet there is
a chance some of that debris will enter the Pilot Burner Gas Valve and contaminate the seal inside the valve. If this
occurs, the possibility exists the valve will not seal properly when turned OFF, thereby allowing a small amount of gas
to ow even after being turned OFF. Often this will result in a small ame that continues to burn in the Pilot Burner
after the feature has been turned OFF.
• Leak in the Main Burner Gas Valve - when debris enters the gas valve by way of either the Inlet or Outlet there is
a chance some of that debris will enter the Main Burner Gas Valve and contaminate the seal inside the valve. If this
occurs the possibility exists the valve will not seal properly when turned OFF, thereby allowing a small amount of gas
to ow even after turned off. Often this will result in a small ame that continues to burn on the Main Burner after the
feature has been turned OFF.
10. Turn the Feature OFF…but Small Flames Continue to Burn Out the Main Burner
SHUTDOWN ISSUES
TROUBLESHOOTING

FPB Pro Series Fire Pits with AWS System REV. A Page 18
OPTIONAL ACCESSORIES
The following accessories are available from your local Firegear Outdoors dealer/distributor.
Each accessory comes with a separate installation manual. Read each instruction thoroughly before installing.
Note: See the Firegear Outdoors catalogue for a variety of ttings and ex connectors also available.
Emergency Stop
(Emergency shut-off valve)
Model: FG-EMER-STOP (includes J-Box
and weatherproof cover)
Timer
(Mechanical gas timer)
Model: FG-TIMER- 2HR
* Includes weatherproof J-box and
cover
ON-OFF Switches
Model: FG-WS-OD (On-Off Wall
Switch; includes J-Box and weather-
proof cover)
FlexFrame
Model: FLEXFRAME-SS (2pc.)
FLEXFRAME-SS3 (3pc.)
Universal brackets to support re pit
when using paver blocks or other
non-combustible enclosures.
Glass Windshields
See catalog for a windshield to t
your application.
Shut-Off Valves
Model: 01-387 ⅜” OD Flare x ½” FIP
Model: 01-487 ½” OD Flare x ½” FIP
Model: 01-266
⅜” OD Flare x ⅜” OD Flare
Model: 01-288
½” OD Flare x ½” OD Flare
Vent Kits
Model: VENT-KIT-6X12SS
(provides 18 sq. in of ventilation per
side of enclosure)
Model: PAVER-VENT-4LNTS
Model: PAVER-VENT-6LNTS
Paver-Control Panel
Model: PAVER-CP-AWS
For use with SWR blocks, includes
lintel, screws, ttings, Tapcon
concrete anchors, face plate with
key valve
Log Sets
Model:
L-SF (Spit Fire) - 17pc (52lbs)
L-Sedona (Sedona) 19pc (200lbs)
Note: When installing log sets on re
features additional support of the burner
pan may be necessary.
Pool/Spa (Water Installations)
Model: FG-AWS-PS-30V320
Power supply for one or up to (4)
re features near a pool/spa.
Must order any Firegear Outdoor
Match Throw (MT) Burning Spur re
pit to use with kit listed above (sold
separately).

REV. A Page 19
FPB Pro Series Fire Pits with AWS System
FIREGEAR LIMITED WARRANTY - 2021
Firegear Outdoors hereby warrants to the end user that products will be free from material and workmanship
defects that prevent safe and correct operation of the product. The warranty commences from date of sale to
the end user for the following period:
CONSUMER RESIDENTIAL APPLICATIONS –MANUFACTURED AFTER 12/02/2019
BURNER SYSTEMS, BURNERS, COMPONENTS AND ACCESSORIES
• LIFETIME WARRANTY ON CONSTRUCTION AND MANUFACTURER DEFECTS
• LIFETIME WARRANTY - STAINLESS STEEL BURNERS AND PANS
• LIFETIME WARRANTY - BRASS BURNERS
• FIVE (5) YEAR WARRANTY - GAS VALVE, SPARK IGNITER, PILOT ASSEMBLIES
• FIVE (5) YEAR WARRANTY - AWS ELECONITC IGNITION SYSTEMS (24VAC, 30 VDC)
• FIVE (5) YEAR WARRANTY - TFS/TMSI ELECTRONIC COMPONENTS
• FIVE (5) YEAR WARRANTY –MT COMPONENTS (KEY VALVE)
• FIVE (5) YEAR WARRANTY - REFRACTORY GAS LOG SETS
• FIVE (5) YEAR WARRANTY - READY TO FINISH/ANF FIRE PIT ENCLOSURES
• FIVE (5) YEAR WARRANTY –SKYTECH MANUACFTURED OPTIONAL CONTROLS
OUTDOOR FIREPLACE –KALEA BAY
• LIFETIME WARRANTY - CONSTRUCTION AND MANUFACTURER DEFECTS
• LIFETIME WARRANTY - STAINLESS STEEL COMPONENTS
• FIVE (5) YEAR WARRANTY - GAS VALVE, PILOT ASSEMBLY, POWER SUPPLY, CONTROLS
• FIVE (5) YEAR WARRANTY –SKYTECH MANUACFTURED OPTIONAL CONTROLS
SANCTUARY SERIES –GFRC FIRE FEATURES
• THREE (3) YEAR WARRANTY - GFRC STRUCTURE
• REFER TO THE APPROPRIATE BURNER SYSTEM FOR WARRANTY
WARRANTY COVERS MANUFACTURING DEFECTS OR STRUCTURAL FAILURE. SMALL STRESS CRACKS AND SURFACE
CRAZING ARE A NATURAL OCCURRENCE IN GFRC PRODUCTS AND NOT COVERED BY WARRANTY.
READY TO FINISH/ANF ENCLOSURES
• FRAME – LIFETIME WARRANTY ON CONSTRUCTION AND MANUFACTURER DEFECTS
ACCESSORIES
• LIFETIME WARRANTY - CONSTRUCTION AND MANUFACTURER DEFECTS
• LIFETIME WARRANTY - STAINLESS STEEL COMPONENTS (LIDS, STAINLESS STEEL COVERS)
• ONE (1) YEAR WARRANTY –ESTOP1-OH, ESTOP2-5H WINDSHIELDS, HOSES AND REGULATORS

FPB Pro Series Fire Pits with AWS System REV. A Page 20
COMMERCIAL APPLICATIONS –MANUFACTURED AFTER 12/02/2019
BURNER SYSTEMS, BURNERS, COMPONENTS AND ACCESSORIES
• TWO (2) YEAR WARRANTY ON CONSTRUCTION AND MANUFACTURER DEFECTS
• TWO (2) YEAR WARRANTY - STAINLESS STEEL BURNERS AND PANS
• TWO (2) YEAR WARRANTY - BRASS BURNERS
• TWO (2) YEAR WARRANTY - GAS VALVE, SPARK IGNITER, PILOT ASSEMBLIES
• TWO (2) YEAR WARRANTY - AWS ELECONITC IGNITION SYSTEMS (24VAC, 30 VDC)
• TWO (2) YEAR WARRANTY –MT COMPONENTS (KEY VALVE)
• TWO (2) YEAR WARRANTY - REFRACTORY GAS LOG SETS
• FIVE (5) YEAR WARRANTY - READY TO FINISH/ANF FIRE PIT ENCLOSURES
• TWO (2) YEAR WARRANTY –SKYTECH MANUACFTURED OPTIONAL CONTROLS
OUTDOOR FIREPLACE –KALEA BAY
• LIFETIME WARRANTY - CONSTRUCTION AND MANUFACTURER DEFECTS
• LIFETIME WARRANTY - STAINLESS STEEL COMPONENTS
• TWO (2) YEAR WARRANTY - GAS VALVE, PILOT ASSEMBLY, POWER SUPPLY, CONTROLS
• TWO (2) YEAR WARRANTY –SKYTECH MANUACFTURED OPTIONAL CONTROLS
SANCTUARY SERIES –GFRC FIRE FEATURES
• THREE (3) YEAR WARRANTY - GFRC STRUCTURE
• REFER TO THE APPROPRIATE BURNER SYSTEM FOR WARRANTY
WARRANTY COVERS MANUFACTURING DEFECTS OR STRUCTURAL FAILURE. SMALL STRESS CRACKS AND SURFACE
CRAZING ARE A NATURAL OCCURRENCE IN GFRC PRODUCTS AND NOT COVERED BY WARRANTY.
READY TO FINISH/ANF ENCLOSURES
• FRAME –LIFETIME WARRANTY ON CONSTRUCTION AND MANUFACTURER DEFECTS
ACCESSORIES
• LIFETIME WARRANTY - CONSTRUCTION AND MANUFACTURER DEFECTS
• LIFETIME WARRANTY - STAINLESS STEEL COMPONENTS (LIDS, STAINLESS STEEL COVERS)
• ONE (1) YEAR WARRANTY –ESTOP1-OH, ESTOP2-5H WINDSHIELDS, HOSES AND REGULATORS