Fireplace World Miami Curve User manual

2
15)
16)
17)
Do not plug this product into a receptacle controlled by
a wall switch or dimmer.
When storing or transporting the unit and cord,keep in a
dry place,free from excessive vibration and store so as
to avoid damage.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE.
Alaways plug heater directly into wall outet or
receptacle.Never use with extension cord or PARTS LIST
CAUTION:
IF YOU USE THIS HEATER IN CONJUNCTION WITH A
THERMAL CONTROL,A PROGRAM CONTROLLER,A TIMER
OR ANY OTHER DEVICE THAT SWITHCHES THE HEATER
ON AUTOMATICALLY,REMEMBER TO OBSERVE ALL
SAFETY WARNINGS AT ALL TIMES. THE FIREPLACE
HEATER HAS SAFETY OVERHEAT PROTECTION. IF THE
OVERHEAT PROTECTION TRIPS,SWITCH OFF ALL
SWITCHES AND WAIT A PPROXIMATELY 5-10 MINUTES.
WARNING:
PROCEDURES AND TECHNIQUES,IF NOT CAREFULLY
FOLLOWED,WILL RESULT IN DAMAGE TO THE
EQUIPMENT,AND WILL EXPOSE THE USER TO THE RISK
OF SERIOUS INJURY,ILLNESS OR DEATH.THIS ELECTRIC
FIREPLACE HEATER IS FOR USE ON 120 VOLTS.THE
CORD HAS A PLUG AS SHOWN AT A IN ILLUSTRATION
BELOW. AN ADAPTER AS SHOWN AT C IS AVAILABLE
FOR CONNECTING THREE-BLADE GROUNDING-TYPE
PLUGS TO TWO-SLOT RECEPTACLES. THE GREEN
GROUNDING LUG EXTENDING FROM THE ADAPTER
MUST BE CONNECTED TO A PERMANENT GROUND SUCH
AS A PROPERLY GROUNDED OUTLET BOX. THE
A 15 AMP CIRCUIT IS REQUIRED TO OPERATE THIS HEATER.
IF THE BREAKER TRIPS WHEN THE HEATER IS USED,YOU
MAY NEED TO MOVE THE HEATER TO ANOTHER LOCATION
OR UNPLUG OTHER APPLIANCES THAT ARE ON THE SAME
CIRCUIT. IF YOU REQUIRE AN EXTENSION CORD,USE ONE
THAT IS RATED AT 1875 WATTS.
ADAPTER SHOULD NOT BE USED IF A THREE-SLOT
GROUNDED RECEPTACLE IS AVAILABLE.
IT SHOULD RESET AUTOMATICALLY ONCE THE UNIT
COOLS DOWN.
Fireplace.............................................................................1
A) Anchor screw.................................................................5
B) Wall anchors..................................................................5
C) Mounting bracket...........................................................1
INSTALLATION
TOOLS REQUIRED: LEVEL, ELECTRIC DRILL, DRILL BITS (8MM (5/16 IN
HAMMER,SAFETY GOGGLES AND GLOVES
)), PHILLIPS
HEAD SCREWDRIVER,
/
retractable power bar(outlet power strip).
the wall/opening as this can effect the performance of the
heater unit.
Please be aware: that no products should be sealed against
Minimum Installation Height:
This suite is supplied with a wall fixing Bracket.
The suite can be installed at any height as long as it is not
below the recommended 300mm. (Please note the 700mm
From floor level to bottom edge of product, Minimum 300mm.
measurement is given as a common installation height).
The recommended installation height is a minimum of 300mm
from the floor level to the underside of the hearth.

3
overheating issues.
The suite is designed as a wall mounted suite; it is not suitable
to be installed at floor level.
Warning: Installing this product below 300mm will cause
Installation:
with x5 screws and wall plugs.
PLEASE NOTE: The screws and plugs provided are only
suitable for a solid wall fixing.
This model is provided with a wall mounting bracket along
If the installation is onto a hollow/stud wall, we recommend
that heavy duty wall anchors or equivalent are used.
1. Measure 700mm from the floor level up the wall, Mark this
measurement with a pencil.
2. Place the bottom edge of the wall bracket on the 700mm
To install the product:
mark, level using a spirit level and mark and drill the x5 fixing
holes.
in place.
4. Locate the x3 slots in the rear of the product, carefully align
these slots with the prongs on the wall bracket, lift and slot the
3. Using the correct wall fixings screw and fix the wall bracket
product into place.
5. Locate the power cable socket on the bottom right hand
side, underneath the hearth on the fire, and plug the power
lead in.
6.The product is now ready to use.
OPERATION
connected to a ground electrical outlet, it is ready to operate.
Note: Ensure the circuit breakers for the power supply are
turned on.
Once the electric heater has been properly installed and
OPERATION WITH THE CONTROL PANEL
to the right of the heater outlet.
The appliance is operated manually using the rocker switch
will stop the main power function.
The heater is preset to start with flame effect.
For low heat function - Press this switch while the O/I
Press this switch for main power function. Press again
switch is in the ON position. The heater will provide low
heat level. Press once again to stop the low heat level
function.
O/I:
O/ :
For high heat function - Press this switch while the O/I
heater will provide high heat level. Press once again to
stop the high heat level function.
O/ :
switch and the O/ - switch are in the ON position. The
Press this switch for ambient side lighting function.
function.
Press once again to stop the ambient side lighting
:
will stop even though the switches may be in the ON position.
Note: When the O/I switch is turned off, all other functions
MAINTENANCE
POWER CORD BEFORE ATTEMPTING ANY MAINTENANCE
OR CLEANING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PERSONAL INJURY.
WARNING: DISCONNECT POWER AND UNPLUG THE
To avoid buring of the skin, please turn off the heater and
cool down it for at least 10 minutes before maintenance.
CLEANING
To clean unit, first turn off the controls on the unit and unplug
the unit from power source.
To clean glass, remove dust with clean dry cloth or to remove
cloth. Do not use abrasive cleaners or spray liquids on the
glass surface.
finger prints and other marks clean glass with clean damp
Metal and metal painted parts should be cleaned with a damp
surfaces.
cloth. Do not use abrasive cleaners or spray liquids on these
STORAGE
When the heater is not in use, the heater should be stored in
should be stored properly to avoid contact with hot or sharp
a dry location, away from possible damage. The power cord
objects.
REPLACEMENT PARTS
ITEM PART # QTY
Mounting kit RO2716-48#1 1