Solas ONE6 LGS-16BI User manual

solasfires.com 1
ONE6 Slim-Line Built-In
DIRECTVENT LOG SET KIT
PART: LGS16BI
INSTALLATION MANUAL
ONLY FOR USE ON SÓLAS MODEL: 16NBICZ
WARNING
This log set kit shall be installed by a qualified service agency in
accordance with the manufacturer’s instructions and all applicable
codes and requirements of the Authority Having Jurisdiction. If
the information in these instructions is not followed exactly, a fire,
explosion or production of carbon monoxide may result causing
property damage, personal injury or loss of life. The qualified
service agency is responsible for the proper installation of this kit.
The installation is not proper and complete until the operation of the
converted appliance is checked as specified in the manufacturer’s
instructions supplied with the kit.
NOT FOR USE WITH VENT-FREE OR OUTDOOR FIREPLACES
SÓLAS BIRCH LOG SET KIT
INSTALLER: Leave this manual with appliance | CONSUMER: Retain this manual for future reference

SÓLAS CONTEMPORARY FIRE
2
KIT CONTENTS:
 1 CERAMIC LOGS  7oz. LAVA ROCK
 1 CERAMIC ROCKS  METAL LOG SET BURNER
LOG SET INSTALLATION
SÓLAS BIRCH LOG SET
BURNER SUPPORT LOCATIONS
Unless the ONE6 Direct-Vent Gas Fireplace was originally ordered with the Birch Log Set, your
fireplace will have shipped from the factory with a Glass Media burner in place. Before installing the
log set burner, you will need to remove the glass burner. See following steps 1-4 to remove the Glass
Media burner. If the fireplace has been ordered with the Log Set Burner, you can skip to Figure 10 –
“INSTALLATION OF BIRCH LOG SET” on Page 4 of this manual.
1. The burner is held in place by 4 sheet metal screws, 2
on the left and 2 on the right. To make access to these
screws easier, we are going to loosen the valve bracket
so it can be moved slightly. Figure 1 shows the screw
on the left under side of the firebox securing the back
of the valve bracket, remove this screw. Keep this screw
in a safe place as it will be needed to secure the valve
bracket again once the logset burner is installed.
REMOVAL OF GLASS MEDIA BURNER
Figure 1

solasfires.com 3
LOG SET INSTALLATION
2. Figure 2 shows the screw on the right underside of
the firebox which secures the front of the valve bracket,
remove this screw. Keep this screw in a safe place a
it will be needed to secure the valve bracket again
once the logset burner is installed.
3. The valve bracket is still secured by a third screw,
without removing this screw, the valve bracket and
valve can be pulled down approximately ½” (12mm)
as shown in Figure 3.
4. The burner is held in place by 4 sheet metal screws,
2 on the left and 2 on the right. Figure 4 shows 2
screws on the left under side of the firebox, remove
these screws. Keep these screws in a safe place as
they will be needed to install the Log Set burner.
5. Figure 5 shows the 2 screws on the right underside of
the firebox, remove these screws. A ⁄”, 6” or longer nut
driver will make removal of these screws easier. Keep
these screws in a safe place as they will be needed to
install the Logset burner.
6. To remove the burner from the fireplace, slide the
entire assembly to the right before lifting up to
remove as shown in Figure 6.
7. Once the glass media burner has been removed,
locate the Logset burner included in the kit LGS-16
as shown below in Figure 7.
Figure 3
Figure 4
Figure 2 Figure 5
Figure 6
Figure 7

SÓLAS CONTEMPORARY FIRE
4
LOG SET INSTALLATION
STEP 1
Install the logset burner within the firebox by lowering
the burner into the firebox (while keeping the burner
pressed toward the right side of the firebox) then
sliding the burner left towards the center of the firebox
to engage the burner orifice as shown in figure 10.
Confirm that the burner inlet tube has engaged the
burner orifice. (Figure 10)
STEP 2
Secure the burner using the (4) #10 sheet metal screws
set aside from steps 4 & 5
STEP 3
Secure the valve bracket using the (2) #10 sheet metal
screws set aside from steps 1 & 2.
STEP 4
Install the 3-rock cluster on the 2 pins located just right
of the pilot. (Figure 11)
Figure 10
Figure 11
> Start HERE if the ONE6 Wall-Mount was originally ordered with a Log Set Burner
NOTE: The log set burner can be configured for either
Natural Gas or Propane by installing or removing a collar
on the burner venturi. Figure 8 shows the venturi inlet with
the collar installed on a burner configured for Natural Gas.
Figure 9 shows the venturi inlet with the collar removed
from a burner configured for Propane. THIS VENTURI IS
NOT ADJUSTABLE. If you need to convert your burner
from Propane to Natural Gas or vice-versa, please order
the appropriate conversion kit for your appliance.
INTALLATION OF BIRCH LOG SET
Collar OFF for LP Collar ON for NG
Figure 8 Figure 9

solasfires.com 5
LOG SET INSTALLATION
STEP 5
Install the center birch log by placing the left side of the
log on the locating pin left of the pilot. The right side of
the log will rest on top of the 3-rock cluster, rotate the
log so it gently touches the rear enamel panel of the
firebox. (Figure 12)
STEP 6
Evenly distribute the included 7oz of lava rock on the
exposed burner top. Cover the burner top completely
but do not compress or “pack” the lava rock tightly.
Pay special attention to tight and hard to reach areas
when placing the media on the burner. It is ok if small
amounts of lava rock are lost over the edge of the
burner. (Figure 13)
Figure 12
Figure 13
Installation of the Birch Log Set is now complete, refer to the ONE6 Installation and
Operation Manual for instructions on final assembly and lighting of the appliance.

THANK YOU FOR CHOOSING
RECORD YOUR PRODUCT INFORMATION
Model #: ________________________ Serial Number: ______________________________
Dte Purchsed: __________________ Date Installed: _______________________________
solasfires.com
We recommend that our
gas hearth products be
installed and serviced by
professionals who are
certified in the U.S. by the
National Fireplace Institute®
(NFI) as NFI Gas Specialists.
www.NFIcertified.org