First Alert FE10G User manual

User’s Manual
Dry Chemical
Fire Extinguisher
Models FE5G, FE5G-M,
FE10G, FE10G-M,
FE1A10G, FE1A10G30
IMPORTANT! Please read carefully and save.
This user’s manual contains important information about your fire extinguisher’s
operation. If you are installing this fire extinguisher for use by others, you must
leave this manual—or a copy of it—with the end user.
Read extinguisher label and the entire user’s manual carefully before installing or
using the unit. Make sure everyone in your household is completely familiar with
the operation of the extinguisher, and review the instructions regularly. In an
emergency, you will not have time to read instructions.
IMPORTANT INFORMATION ABOUT
FIRE EXTINGUISHERS
NOTE: Be sure the extinguisher is rated to fight the type of fire
most likely to occur in the area you choose to install it. Since house-
hold fires commonly start in the kitchen, you should always install
an extinguisher in the kitchen. For added security, you should also
install additional extinguishers in utility areas, and other living areas in
your household.
FE5G and FE5G-M are rated Class 5-B:C.
FE10G and FE10G-M are rated Class 10-B:C.
FE1A10G and FE1A10G30 are rated Class 1-A:10-B:C.
READ BEFORE INSTALLING OR USING
THIS FIRE EXTINGUISHER!
Fire extinguishers are classified by fire type. The A, B and C
rating system defines the kinds of burning materials each fire
extinguisher is designed to fight. The numbers in front of the A,
B, or C indicate the rating for size of the fire the unit can extin-
guish. Using the wrong type of fire extinguisher can do more
harm than good. Make sure you understand which fire extin-
guisher to use on each class of fire!
Class A rating: The agent/powder is suitable for
fighting small fires involving wood, paper, cloth,
rubber, and some plastics.
Class B rating: The agent/powder is suitable for
fighting small fires involving grease, oil, gasoline,
kerosene, and other flammable liquids.
Class C rating: The agent/powder is suitable for
fighting small fires in "live" electrical equipment.
WHERE TO INSTALL THIS EXTINGUISHER
A Fire Extinguisher Should Be Mounted:
• In the vicinity of (but not on or in) a potential source of heat
and/or fire, like an oven or stove.
• Where it is easy to reach, near an exit or an escape route from
the room.
• In a location that is convenient, in plain sight, and 3-1/2 to 5
feet (1 to 1.5 meters) above the floor.
• Store the extinguisher high enough to keep it out of the reach
of small children.
• On a clean, dry surface where the temperature does not go
above 120° F (49° C) or below –40° F (–40° C).
HOW TO INSTALL THIS EXTINGUISHER
NOTE: Since wall surface types vary, mounting screws are not
included. Purchase screws or bolts specifically designed for the sur-
face on which you will mount the fire extinguisher. The fire extinguisher
label lists its maximum weight. Mounting screw head type should be
#8 pan on round head screws with #8 flat washers.
INSTALL THE MOUNTING BRACKET ON A WALL
1. The extinguisher has a bracket for
wall mounting. Install the mounting
bracket on a wooden stud or other
solid surface that will support the
weight of the extinguisher using
the screws or bolts you purchased
(see "Note" above).
2. After installing the mounting brack-
et, replace the extinguisher on the
bracket with the label facing out-
ward, so the label can be easily
read. Raise and wrap the bracket
straps around the cylinder and
snap the buckle closed.
INSTALLING THE MOUNTING BRACKET IN A
MARINE CRAFT (Excluding Model FE1A10G30)
According to the NFPA Standard 302 (Fire protection Standard for
Pleasure and Commercial Motor Craft):
•On marine crafts, portable fire extinguishers shall be located to be
readily accessible. Extinguishers shall be secured with a marine
bracket to permit immediate release.
•On marine crafts, extinguisher agent cylinders shall be mounted a
minimum of 2 inches (5 cm) above moist or wet surfaces to reduce
the danger of corrosion.
CHECKING AND INSPECTING THE
FIRE EXTINGUISHER
1. Inspect the extinguisher once a week.
Remove the extinguisher from the
mounting bracket and inspect the
gauge. If the yellow pointer is in the
GREEN area, the extinguisher is
properly pressurized and ready to use.
If the pointer drops into the RED
area, the extinguisher has lost some
pressure and should be replaced.
2. Check for signs of damage or misuse. Make sure you can still read
all the text on the label. Carefully examine the surface of the extin-
guisher for corrosion. You can help prevent corrosion by cleaning
the extinguisher if it gets wet or dirty. If you notice corrosion dur-
ing the warranty period, return the unit to First Alert®(See "Limited
Warranty" at the end of this manual).
3. Make sure the tamper indicator ("safety seal") is still intact and the
nozzle is clean and unobstructed.
4. When you finish inspecting the extinguisher, always put it back
securely into the mounting bracket.
For more information about fire extinguishers, consult the NFPA
Standard #10, "Portable Fire Extinguishers," available from the
National Fire Protection Association, Inc., Batterymarch Park, Quincy,
MA 02169, USA.
•Do not mount the extinguisher on drywall or plaster without
adequate support. Use strong screws or bolts to mount the
bracket securely into solid wood or metal that can support it,
like a wooden partition stud. Secure mounting is needed so
you can remove the extinguisher quickly and easily in an emer-
gency. Also, if the extinguisher is not held securely, it could
drop to the floor and injure people or damage the extinguisher
•DO NOT BREAK THE SAFETY SEAL! This seal prevents
accidental discharge of the fire extinguisher. Break the seal
only in an emergency before using the fire extinguisher.
1
TABLE OF CONTENTS
Important Information About Fire Extinguishers . . . . . . . . . . . . . .1
Read Before Installing or Using This Fire Extinguisher . . . . . . . . .1
Where to Install This Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . .1
How to Install This Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Checking and Inspecting the Fire Extinguisher . . . . . . . . . . . . . . .1
How to Operate Your Fire Extinguisher in a Fire Emergency . . . .2
After the Fire is Extinguished . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
How to Clean After Using a Fire Extinguisher . . . . . . . . . . . . . . . .2
If Your Fire Extinguisher Needs Service . . . . . . . . . . . . . . . . . . . . .2
Disposing of a Used Extinguisher . . . . . . . . . . . . . . . . . . . . . . . . .2
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
All Rights Reserved. © 2004 BRK Brands, Inc.
First Alert®, 3901 Liberty Street Road, Aurora, IL 60504-8122
Consumer Affairs: [phone]. •www.firstalert.com
M08-0038-002 M07/04
•This extinguisher is designed for use against small fires that
have just started and are small enough to fight safely. It is
not designed to fight large fires that are burning out of con-
trol. If the fire is too hot or smoky for you to get within 6 feet
(2 meters) of it, do not try to fight it yourself. Warn everyone,
evacuate the premises, and have someone call the Fire
Department from outside the building. Trying to fight a large
fire yourself can result in injury or death.
•Do not puncture or burn any fire extinguisher. The contents
are under pressure, and the extinguisher could explode.
•Never locate this extinguisher close to an engine, stove or
other source of heat. It is pressurized and could rupture or
explode if exposed to temperatures over 150°F (66°C).
•This extinguisher contains a dry powder extinguishing agent.
The agent/powder is nontoxic, but can irritate skin. When using
this unit, avoid breathing the powder. Always ventilate the area
after use.
•DO NOT CHECK THE PRESSURE OR TEST THE FIRE
EXTINGUISHER BY SQUEEZING THE TRIGGER, EVEN
BRIEFLY. ONCE USED, IT WILL GRADUALLY LOSE
PRESSURE AND WILL NOT BE FULLY CHARGED FOR USE
IN AN EMERGENCY.
•When the pointer drops into the red area, the extinguisher
may still be pressurized. You must discharge the unit
completely before disposing of it!
DISCARD WHEN
POINTER IS IN
THE RED
AREA
Model
FE5G
Model
FE5G-M
Models
FE10G,
FE10G-M
Models
FE1A10G,
FE1A10G30

HOW TO OPERATE YOUR FIRE
EXTINGUISHER IN A FIRE EMERGENCY
TO FIGHT THE FIRE
1. Remove the extinguisher from the mounting bracket.
2. Hold the unit firmly with the nozzle facing away from you. Pull out
the pin to break the “Safety Seal”. You won’t be able to squeeze
the trigger until the safety seal is removed.
3. Stand back 6 feet (2 meters) from the fire and make sure the fire is
not between you and your exit.
4. Hold the extinguisher upright and aim the nozzle at the base
of the fire.
5. Squeeze and hold the trigger to discharge the powder.
6. Sweep the spray at the base of the burning material, using quick
side-to-side motions. (If the spray scatters the fire, move back.)
7. Move slowly towards the fire as the extinguisher spray pushes the
fire back. Maintain a 6-foot (2 meter) distance between you and
the front of the fire at all times.
8. Completely discharge the contents of the extinguisher and make
sure the fire is completely out. Flashbacks are common with fires.
9. For kitchen fires on a kitchen stove, turn off the stove immediately
if possible, otherwise as soon as it is safe.
10. If you suspect a fire had an electrical origin, shut off the electrical
power, if possible, without eliminating your escape route. Do not
touch electrical wires or appliances.
11. After you have completely discharged your extinguisher, leave the
building and close all the doors behind you.
AFTER THE FIRE IS EXTINGUISHED
Do not turn the electrical power back on or plug in any appliances
until the area has been cleaned up completely. It is very important to
remove the powder from electrical equipment after a fire. If the
powder gets wet, it can conduct electricity. (Using a dry chemical
extinguisher on wet electrical equipment may be hazardous for this
reason.) This may worsen an electrical leakage problem, impair the
equipment’s insulation, or create an electrical shock hazard.
If the fire was on a kitchen stove:
•Make sure the oven and all burners are turned off.
•Clean up the powder completely before using the stove or oven.
See “How to Clean After Using a Fire Extinguisher”. Ventilate the
area thoroughly.
If you think the fire had an electrical origin:
•Shut off the electrical power, if possible--do not touch any
electrical wires or appliances.
•Leave the building and close all doors behind you. Call the Fire
Department and have them inspect the premises. As soon as they
say it’s safe to return, ventilate the area thoroughly.
•Have a licensed electrician inspect your electrical system. Do not
turn the power back on or plug in any electrical equipment until
the inspection has been completed.
•Make sure your extinguisher may be safely and effectively
used on the small fire you want to fight. Always use extreme
caution when fighting any fire. Fight a fire only where there is
a clear escape path to allow you to get out safely if the fire
gets worse.
•Avoid breathing smoke and heated fumes; stay low if neces-
sary. Burning materials will release toxic fumes. Inhaling
these fumes may cause injury or death.
•Always stand back far enough away from the fire—near an
exit—and make sure nothing is between you and your
escape route. If you get too close to a fire, you risk getting
burned or hit by splattering material like grease. If the fire is
too hot or smoky for you to get within 6 feet (2 meters), DO
NOT try to fight the fire yourself. Evacuate immediately and
call the Fire Department.
•For fires on a kitchen stove, turn oven or burners off immedi-
ately if possible. If you can’t reach the oven or burner con-
trols safely, extinguish the fire first, then turn them off.
•Fight the fire from an upwind direction with your back to any
strong air current. Trying to fight a fire with currents blowing
towards you can result in serious injury.
HOW TO CLEAN AFTER USING A FIRE
EXTINGUISHER
NOTE: The powder spray from the extinguisher may spread over a
wide area, and may soil upholstery, carpets and walls.
•Sweep/vacuum up as much of the powder as possible. Then use
a damp cloth to wipe off the remaining agent.
•If you have any questions about cleaning appliances that the
agent has come into contact with, please contact the appliance
manufacturer.
IF YOUR EXTINGUISHER NEEDS SERVICE
This fire extinguisher is a disposable device that is NOT rechargeable.
Do not try to service or repair this fire extinguisher under any
circumstances. Do not try to remove the nozzle or valve assembly.
This is a pressurized device that can cause serious injury if
tampered with.
If there is a problem and it is still under warranty, please see “How to
Obtain Warranty Service”in the Limited Warranty.
DISPOSING OF A USED EXTINGUISHER
Completely discharge the extinguisher outdoors by turning the unit
upside down and pulling the trigger. Dispose of the empty unit
properly and replace it with a new fire extinguisher.
Never puncture, burn or expose this fire extinguisher to tempera-
tures over 150°F (66°C) even if it is fully discharged. The contents
are under pressure and it could explode.
LIMITED WARRANTY
BRK Brands, Inc. ("BRK") the maker of First Alert®brand products,
warrants that for a period of five years from the date of purchase, this
product will be free from defects in material and workmanship. BRK,
at its option, will repair or replace this product or any component of
the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or
component. If the product is no longer available, replacement may be
made with a similar product of equal or greater value. This is your
exclusive warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales
receipt. Proof of purchase is required to obtain warranty performance.
BRK dealers, service centers, or retail stores selling BRK products do
not have the right to alter, modify or any way change the terms and
conditions of this warranty.
This warranty does not cover normal wear of parts or damage result-
ing from any of the following: negligent use or misuse of the product,
use on improper voltage or current, use contrary to the operating
instructions, disassembly, repair or alteration by anyone other than
BRK or an authorized service center. Further, the warranty does not
cover acts of God, such as fire, flood, hurricanes and tornadoes.
BRK shall not be liable for any incidental or consequential damages
caused by the breach of any express or implied warranty. Except
to the extent prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose is limited in duration
to the duration of the above warranty. Some states, provinces, or
jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages or limitations on how long an implied warranty
lasts, so the above limitations or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other
rights that vary from state to state, or province to province.
How to Obtain Warranty Service:
Service: If service is required, do not return the product to your retail-
er. In order to obtain warranty service, contact the Consumer Affairs
Division at 1-800-323-9005, 7:30 AM to 5:00 PM, Central Standard
Time, Monday through Friday. To assist in serving you, please have
the model number and date of purchase available when calling.
Address: 303 Nelson Avenue, Neosho, MO 64850-8806
M08-0038-002 M07/04
First Alert®is a registered trademark of the First Alert Trust.
Remove Extinguisher
from Bracket
Break the
Safety Seal
Squeeze and Hold
Trigger To Discharge
Powder. Sweep
Side to Side.
This unit will not operate with mounting bracket attached. The
extinguisher must be removed from the mounting bracket or it
cannot discharge its contents to fight a fire.
2