Fisher & Paykel DishDrawer DS605 User manual

Importand
SAVE THESEINSTRUCTIONS
T,_emodels shown in this document may not be available in all markets and are subject to change at any time. For current details about modal and specilication availability in your country, please go to our
web.site www.lisherpaykel.com or contact your local Fisher & Paykel dealer.
SAFETYAND WARNINGS
Electrical hazard
Before installing the DishDrawer ®,remove the house fuse or open the circuit breaker.
[f permanently connecting the DishDrawer ®,be sure the power is isolated and the DishDrawer ®unplugged.
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current, This
appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug, The plug must be plugged into a n appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service
representative if you are in doubt as to whether the appliance is properly grounded.
Do not modify the power supply plug provided with the appliance -if it will not fit the outJet, have a proper outJet installed by a qualified electrician. Do not use an extension cord, adapter plug or
multiple outJet box.
Failure to do so may result in electrical shock or death.
Cut hazard
Take care - pane[ edges are sharp.
FaiJure to use caution couJd resuJt in injury or cuts.
Important safety precautionJ.
installation of this DishDrawer ®requires basic mechanical and electrical skills.
Be sure to leave these instructions with the Customer.
installation must comply with your local building and electricity regulations.
At the completion of the DishDrawer _installation, the installer must perform the
Final Check List.
Remove all packaging materials supplied with the DishDrawer ®.
This DishDrawer _is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibifity of the plum bar and
electrician to ensure that each installation complies with ell Codes and Regulations.
The DishDrawer ®MUST be installed to allow for future removal from the enclosure ff service is required.
The switched power outlet must be outside the DishDrawer ®cavity so that it is accessible after installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the
power supply cord.
If the DishDrawer _is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.
Make sure only new hoses are used for connection (supplied with DishDrawer_). Old hoses should not be
reused.
Failure to install the DishDrawer ®correctly could invafidate any warranty or liability claims.
If the product is installed in a motor vehicle, boat or similar mobile facilit}; you must bring the vehicle, boat
or mobile facifity containing the product to the service shop at your expense or pay the service technician's
travel to the location of the product.

PRODUCT D MENS ONS
J_)Stt lJ t/O_) iJo_ro;7_s _)r /lJd lV tJO_) ;_ii! ;_OS#SOt)l',
D
C
t
I
I
i
i
Product dimensions (inches (mm)) _ _ B-
-Pl Cb
A overall height _ of produ(t 16 ys"(409) 16 y8"(409) 161/8"(409)
B overall width of product 23 _6" (595) 23 _d' (595) 23 _o" (595)
C overall depth of prod uct (exchcurvature/handle) 22 _6" (570) 22 _6" (570) 22 _6" (570)_
D depth of drawer (open) (c,xcLcurvature/handle) 20 Y2"(520) 20 1/2"(520) 20 1/2"(520)
Eheight _÷of chassis 16 Ys"(409) 16 Yd' (409) 16 Ys"(409)
Fdepth of chassis 21 3A"(552) 21 3A" (552) 21%" (552)
G depth of drawer front pane[ (c,xcl, curvature/hand e) 11_6"(18) 11_6"(18) 11_6"(18)
Hdepth of curvature or handle 1 sA6"(30) _*e n/a
[ height of drawer front 151/2" (394) 151¼6" (398) 15 1X6"(398) mm
J height of venting area at base of prod uct ¼" (7) 3/s" (9) %" (9)
Kheight of installation tab slots (on top ofchass[9 ¼d' (2) ¼6" (2) ¼6" (2)
L heig ht_<oftop of d rawer to top of chassis ¼"(7) xd' (2) n/a
7
Chassis heights ndude tab sots _' Panelth ckness- 6" (18 "_m) :÷ Designer handle- _ %" (4I mrr/,, Cu'ved handle- 1 _id'(36 n, rr/)
5
No_e: for Prefin shed Hat door models, the height from the top of handle to the top of door - 2 _6" (595 ram)
\
Cabinetry dimensions (inches (ram)) _ _ _-
Ainside height of cavity 16¼"(412) 16¼"(412) 16 ¼"(412)
B inside width of cavity 23 %" (600) 23 %" (600) 23 %" (60@
C inside depth of cavity (inside) 22 %" (580) 22 %" (580) 22 %" (580)
D clearance below benchtop Min. W'(3) _ Min, W'(3) _ Min. W'(3) _
Clearance is measured from the underside of benchtop to the chassis
Minimum clearances (inches(mm))
W' (13 mm) -_

@
Drain hose
support (1)
PARTSSUPPUED
Drain hose Wire clip (2) Clamp (1) Phillips Washer(1) Moisture protection EdgeProtector (1)
joiner (1) 16 mm tape (1) (if servicehole
screws(% pcTrtitionismetcT/)
Ifthe Drain hose(s)supplied are not long enough to reachyour services,you must usea Drain HoseExtension Kit P/N925798which will extend the drain hose(s)by 3.6m.The kit isavailablefrom the nearestFisher&Paykel
Authorized ServiceAgent, or Tollfree 1.888.936.7872or www.flsherpaykekcom.
CAVITY PREPARATION
_F
..)e
lmportand
Besuretheedgesof theservicesholeare smoothor covered.If theservicesholeisthrough ametal
partition theholemustbeprotected with theEdgeProtectorsuppliedtopreventdamagetothe
powercordor hoses.
These marks indicate mounting tab screw locations.
Note: Toalign drawer front to adjacent cabinetry, the product to countertop clearancecan
be increased to 1/8"(3 ram).
Preferredposition. Ifadequate clearance, serviceshole can be higher.
If hole is higher,ensure drain hose(s)are routed straight into the waste connection.
Water Connection
Recommended HOT(Maximum 140°F/60°C).
Supplied hoseto suit 3/8" (9 mm) male compression fitting.
Water Pressure Max Min
Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi)
Other models 1 MPa (145 psi) 0.03 MPa (4.3 psi)
Drains will need to be separated to satisfy kosher requirements. Wesuggest you confirm
acceptability with your local rabbi in respect to kosher installations.
Drain hose 79" 71 "
(2011 mm) (1794 mm)
Inlet hose 37" 53"
(1551 ram) (1344 mm)
Power cord 51" 28"
(935 mm) (719 mm)
Left hand
side Right hand side
max. o 11/2"(38 mm)
Note: Services can be located
• , _de of DishDrawer®"
.... I
max. 17 1¼6"
_(450 mm) i
Adjacentcabinetrymust not
extendabovecadty base
min. 7z/8"
i(200 mm)
L_
L110-120 VAC
max. 15 A

OPTIONALLY HARD W R NG THE PRODUCT
Ensure the drawer is removed
and then rotated counter-
clockwise to prevent kinked
hoses.
©
(150 ram)
Remove Power supply
\\
Remove knock-out for cable
clamp. Fit suitable cable clamp
for the conduit and terminate
the wiring as shown. Ensure the drawer clips ' *'
on both sides are reset. F_
Ensure the drawer is
now rotated
clockwise back.
,_ ........(14
Before refitting the drawer, j/ .....
/
ensure the hoses are not __'
twisted and the latches at
the rear of each drawer t/J
runner are facing forward. _-t_ /

_ ROUTE'THEHOSESAND MOVE IN'[O T'HECAVITY
i.....................
Tie together to avoid kinking
REMOVE THE DRAWER AND SECURETHE PRODUC"]
Ensure the tub is removed
and then rotated counter-
clockwise
1 3Ad'
(30 mm)
Ensurehosesandcord
arenot kinked or twisted.
The mounting tabs are in
pairs, one on each side of
the product.
Ensure the sound
insulation is repositioned
correctly.