Fisher & Paykel MINIMAL VB24SDEB1 User manual

INSTALLATION GUIDE
US CA
MINIMAL VB24SDEB1 & VB30SDEB1
CONTEMPORARY VB24SDEX1 & VB30SDEX1
PROFESSIONAL VB30SPEX1
VACUUM SEAL DRAWER

3
CONTENTS
Safety and warnings 4
Vacuum seal drawer models 5
Unpack your product 6
Electrical specifications 6
Parts supplied 7
Tools required 7
Product dimensions - 24" minimal & contemporary models 8
Product dimensions - 30" minimal & contemporary models 9
Product dimensions - 30" professional models 10
Cabinetry dimensions - 24" minimal & contemporary models 11
Cabinetry dimensions - 30" minimal & contemporary models 12
Cabinetry dimensions - 30" professional model 13
Installation options 14
Prior to installation 16
Installing the drawer 17
Adjusting the depth 18
Adjusting the height 18
Installer checklist 19

4
SAFETY AND WARNINGS
!WARNING!
Tip Hazard
This product may tip. Keep children away and
take care. Failure to follow this advice may
result in injury.
• Drawer must be secured in place by supplied
screws.
• Ensure there is a fixed shelf directly above
the drawer if it is not installed under another
product.
!WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges may be sharp.
• Do not put fingers in the drawer when closing.
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
• If the product is damaged, switch the appliance
off and disconnect it from the mains to avoid
possible electric shock.
!WARNING!
420-630 lb
190-285 kg
Weight Hazard
Failure to follow this advice may result in
damage or personal injury.
• Ensure the bottom shelf of the cabinetry can fully
support the weight of combined appliances.

5
SAFETY AND WARNINGS VACUUM SEAL DRAWER MODELS
READ AND SAVE THIS GUIDE
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the
important safety guides listed below. Read all the instructions before using the appliance.
Installation
zPlease make this information available to the person installing the product.
zThe appliance must be installed by a qualified installer, or Fisher & Paykel trained and
supported service technician to avoid faulty electrical connection.
zEnsure the installation complies with all clearance requirements and applicable standards
and regulations.
zWhen installed in combination with a companion product, the companion product can be
placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be
able to support the weight of both products.
zEnsure the cabinetry is square and level and with correct dimensions.
zIf installing the appliance directly underneath an oven, ensure you do not damage the
oven’s lower trim. Fisher & Paykel does not accept any responsibility for any damage
resulting from incorrect installation.
zBefore installing the appliance, inspect for any signs of damage. Do not install or use
damaged appliances.
zBe careful when stacking the appliances on top of each other to avoid damage to the
appliances.
Electrical
zAll connections for electrical power and earthing must be done by a qualified electrician
and must comply with local codes and ordinances.
zBefore installation, ensure that the voltage and frequency listed on the data plate
corresponds with the household electrical supply.
zWhen combining with another appliance, ensure each appliance has its own power outlet.
Avoid sharing the power point to prevent accidental switching off of the appliance.
zEnsure your appliance is properly grounded (earthed).
zConnect the drawer to a properly rated, protected and sized power supply circuit to avoid
electrical overload.
zDo not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet
box) to connect the drawer to the power supply. Ensure the power supply cord is located
so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
zEnsure there is a switched outlet in an easily accessible area within 35 7/16” (900mm) of
the centre rear of the product.
Servicing
zDo not repair or replace any part of the appliance unless specifically recommended in the
user guide. All other servicing should be done be a Fisher & Paykel trained and supported
service technician or qualified person.
zAlways disconnect the power supply before doing any installation, maintenance or repair
work.
zIf the power supply cord is damaged, it must be replaced by a qualified electrician or
Fisher & Paykel trained and supported service technician.
24" Vacuum seal drawer,
Minimal style
VB24SDEB1
24" Vacuum seal drawer,
Contemporary style
VB24SDEX1
30" Vacuum seal drawer,
Minimal style
VB30SDEB1
30" Vacuum seal drawer,
Contemporary style
VB30SDEX1
30" Vacuum seal drawer,
Professional style
VB30SPEX1

6
UNPACK YOUR PRODUCT ELECTRICAL SPECIFICATIONS
Remove the Vacuum Seal Drawer and accessories box from the packaging. Recycle the
materials that can be reused. Dispose packaging materials in accordance with local regulations
on waste disposal.
Inspect the Vacuum Seal Drawer for any signs of damage. Do not install the Vacuum Seal
Drawer if it has been damaged. If the product is damaged, contact your local Fisher & Paykel
dealer.
RECYCLE
RESPONSIBLY
All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and
supported service technician.
VB24 VB30
Supply 110 VAC, 60 Hz 110 VAC, 60 Hz
Service 10 amp circuit 10 amp circuit
Maximum Power 520 W 520 W
Power outlet* 3-prong grounding-type 3-prong grounding-type
Power cord (total length) 70 7/8" (1800mm) 70 7/8" (1800mm)
* The power outlet must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.

7
Installation guide (1)
Vacuum stopper (1) Stopper adapter (1)
Service & Warranty (1)
SERVICE & WARRANTY
SERVICE ET GARANTIE
ΣΈΡΒΙΣΚ ΑΙ ΕΓΓΎΗΣΗ
SERVIZIO E GARANZIA
SERVICE & GARANTIE
HUOLTO JA TAKUU
SERVICE OG GARANTI
保修和维修
服務和保修
Suction inlet adapter (1)
INSTALLATIONGUIDE
US CA
MINIMAL VB24SDEB & VB30SDEB
CONTEMPORARY VB24SDEX & VB30SDEX
PROFESSIONAL VB30SPEX
VACUUM SEAL DRAWER
User guide (1)
Tube (1)
USER GUIDE
US CA
VACUUM SEAL DRAWER
MINIMAL VB24SDEB & VB30SDEB
CONTEMPORARY VB24SDEX & VB30SDEX
PROFESSIONAL VB30SPEX
PARTS SUPPLIED TOOLS REQUIRED
T20 star head
countersunk screw 4x25
WB30 models (4)
WB24 models (2)
T20 star head
screw 4x15 (4)
Anti-tip bracket (2)
5mm Hex key T20 star-head screwdriver Flat-head screwdriver Pliers
External vacuuming accessories kit

8
PRODUCT DIMENSIONS - 24" MINIMAL & CONTEMPORARY MODELS
Actual product dimension may vary by ± 1/16 (2 mm).
C
I
H
E
PLAN
ISOMETRIC
FRONT
B
A
PROFILE
D
G
F
J
PRODUCT DIMENSIONS
VB24SD
IN MM
A Overall height of drawer 5 1/2 140
B Overall width of drawer 23 7/16 596
C Overall depth of drawer* 22 1/4 566
D Height of chassis 5 1/2 140
E Width of chassis** 21 7/8 556
F Depth of chassis*** 21 1/2 546
G Height of drawer front panel 5 3/8 136
H Depth of drawer front panel and flange 13/16 20
I Depth of open drawer 16 5/16 414
J Height from bottom of chassis to
bottom of front panel 1/16 2
K Depth from front of door to side bracket 15 1/8 384
* Includes front panel and power plug
** Includes side brackets
***Includes power plug
PRODUCT WEIGHT
VB24SD
LBS KG
Total weight of drawer* 84 38
*including packaging
k

9
PRODUCT DIMENSIONS - 30" MINIMAL & CONTEMPORARY MODELS
Actual product dimension may vary by ±1/16 (2 mm).
G
j
D
F
PROFILE
H
PLAN
c
E
I
FRONT
a
b
ISOMETRIC
PRODUCT DIMENSIONS
VB30SD
IN MM
A Overall height of drawer 10 11/16 271
B Overall width of drawer 29 15/16 761
C Overall depth of drawer* 22 1/2 572
D Height of chassis 10 11/16 271
E Width of chassis** 28 3/8 720
F Depth of chassis*** 21 3/4 552
G Height of drawer front panel 10 1/2 267
H Depth of drawer front panel and flange 13/16 20
I Depth of open drawer 16 1/2 419
J Height from bottom of chassis to
bottom of front panel 1/16 2
K Depth from front of door to side bracket 16 5/16 415
* Includes front panel and power plug
** Includes side brackets
***Includes power plug
PRODUCT WEIGHT
VB30SD
LBS KG
Total weight of drawer* 108 49
*including packaging
K

10
PRODUCT DIMENSIONS - 30" PROFESSIONAL MODELS
Actual product dimension may vary by ±1/16 (2 mm).
PRODUCT DIMENSIONS
VB30SP
IN MM
A Overall height of drawer 10 11/16 271
B Overall width of drawer 29 15/16 761
C Overall depth of drawer* 22 1/2 572
D Height of chassis 10 11/16 271
E Width of chassis** 28 3/8 720
F Depth of chassis*** 21 3/4 552
G Height of drawer front panel 10 1/2 267
H Depth of drawer front panel and flange 13/16 20
I Depth of open drawer 16 1/2 419
J Height from bottom of chassis to
bottom of front panel 1/16 2
K Width of handle 29 736
L Depth of handle 2 1/4 58
M Depth from front of door to side bracket 16 5/16 415
* Includes front panel and power plug
** Includes side brackets
***Includes power plug
PRODUCT WEIGHT
VB30SP
LBS KG
Total weight of drawer* 108 49
*including packaging and handle
e
c
H
I
B
a
FRONT
PLAN
d
F
PROFILE
ISOMETRIC
J
G
l
k
m

11
CABINETRY DIMENSIONS - 24" MINIMAL & CONTEMPORARY MODELS
Actual product dimension may vary by ±2 mm.
CABINETRY DIMENSIONS
VB24SD
INCHES MM
A Minimum inside height of cavity 5 9/16 142
B Minimum inside width of cavity 22 1/16 560
C Minimum inside depth of cavity 22 1/2 572
D Overall width of cabinetry 23 5/8 600
E Minimum clearance between top of front panel
and upper cabinetry panel 1/8 3
F Minimum clearance between bottom of front
panel and lower cabinetry panel 1/16 2
* The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
e
f
PLAN
c
b
PROFILE
a
d
PO*
PO*
PROUD INSTALL
FLUSH INSTALL
13/16 (20mm)*
13/16 (20mm)*
* Depth of drawer front panel including attachment flange.

12
CABINETRY DIMENSIONS - 30" MINIMAL & CONTEMPORARY MODELS
Actual product dimension may vary by ±2 mm.
a
PROFILE
e
f
*PO
PLAN
c
b
d
*PO
CABINETRY DIMENSIONS
VB30SD
INCHES MM
A Minimum inside height of cavity 10 3/4 273
B Minimum inside width of cavity 28 1/2 724
C Minimum inside depth of cavity 22 1/2 572
D Overall width of cabinetry 30 762
E Minimum clearance between top of front panel
and upper cabinetry panel 1/8 3
F Minimum clearance between bottom of front
panel and lower cabinetry panel 1/16 2
* The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
PROUD INSTALL
FLUSH INSTALL
13/16 (20mm)*
13/16 (20mm)*
* Depth of drawer front panel including attachment flange.

13
CABINETRY DIMENSIONS - 30" PROFESSIONAL MODEL
Actual product dimension may vary by ±2 mm.
a
PROFILE
c
e
f
*PO
PLAN
b
d
*PO
CABINETRY DIMENSIONS
VB30P
INCHES MM
A Minimum inside height of cavity 10 3/4 273
B Minimum inside width of cavity 28 1/2 724
C Minimum inside depth of cavity 22 1/2 572
D Overall width of cabinetry 30 762
E Minimum clearance between top of front panel
and upper cabinetry panel 1/8 3
F Minimum clearance between bottom of front
panel and lower cabinetry panel 1/16 2
* The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
PROUD INSTALL
FLUSH INSTALL
13/16 (20mm)*
13/16 (20mm)*
* Depth of drawer front panel including attachment flange.

14
This installation is suitable for Minimal, Contemporary &
Professional 24" and 30" Vacuum seal drawers. A fixed shelf
must be provided above the drawer.
STANDALONE INSTALLATION COMBINED WITH SINGLE OVEN COMBINED WITH COMPANION PRODUCT
This combination is suitable for 24" and 30" Vacuum seal
drawers that can fully support 24" and 30" Fisher & Paykel
wall ovens, respectively.
PROFILE
Top shelf
Bottom shelf
Vacuum Seal Drawer
FRONT FRONT
PROFILE
Single oven
Vacuum Seal Drawer
INSTALLATION OPTIONS
This combination is suitable for 24" and 30" Vacuum seal
drawers that can fully support 24" and 30" Fisher & Paykel
companion products, respectively.
FRONT
PROFILE
Companion product
Vacuum Seal Drawer
Top shelf
Bottom shelf

15
COMBINED WITH DOUBLE OVEN
FRONT
PROFILE
This combination is suitable for 30" Vacuum seal drawer that can fully support a
30" Fisher & Paykel double oven.
Double oven
Vacuum Seal Drawer
Bottom shelf
COMBINED WITH SINGLE OVEN & COMPANION PRODUCT
INSTALLATION OPTIONS
This combination is suitable for 30" Vacuum seal drawer that can fully support both
Fisher & Paykel 30" double oven and companion product. A shelf is required above the oven
to support the companion product. Ensure the bottom shelf can fully support the weight of all
appliances.
PROFILE
Companion product
Top shelf
Wall oven
Bottom shelf
Vacuum Seal Drawer
30" Companion Trim Kit
FRONT

16
PRIOR TO INSTALLATION
Locate the attachment position of
the anti-tip brackets in both sides
of the cabinetry,
Ensure the location of the anti-tip
brackets matches the location of
the side brackets of the drawer.
Refer to 'Product dimensions' for
location of side brackets.
Secure the anti-tip brackets with
screws.
INSTALL THE AIR FILTER REMOVE THE TRANSIT SCREWS
The transport screws must be removed before starting up for the first time to avoid damage
to the drawer.
INSTALL THE ANTI-TIP BRACKETS
The anti-tip brackets prevent the drawer from tipping over when opening the drawer. Do not
open the drawer if the anti-tip brackets are not installed.
2Insert the locking cap in the holder.
3Use a flathead screwdriver to screw the
air filter into the air filter opening.
1Pull out the locking cap with pliers.
4Slide the air filter cover over the air filter
opening.
locking cap
holder
air filter
air filter cover
Unscrew the transport screws from under
the power cable and holder.
transport
screws
holder
power cable

17
Connect the power plug into the
power outlet.
Slide the drawer carefully into the
cabinetry.
2
Push the drawer back into the
cabinetry while ensuring the side
brackets engages the anti-tip
brackets.
Align the front panel* with the
cabinetry as desired.
Open the drawer and extend fully.
Secure the attachment flanges of
the drawer to the side edges of
cabinetry with 4x20 T20 star head
countersunk screws.
4
1
INSTALLING THE DRAWER
3
* Flush alignment illustrated.

18
ADJUSTING THE HEIGHT
Open the drawer fully, and slightly
loosen the two screws.
1
2
3
Adjust to the required height and then
re-tighten the screws. The height is
adjustable within 5mm.
Close the drawer and check the
alignment. Adjust again if necessary.
The front panel of the drawer can be adjusted vertically to align with the surrounding
cabinetry.
ADJUSTING THE DEPTH
Open the drawer fully.
Using a hex key, turn the adjustment
screw to move the front panel forward.
Turn clockwise to move backwards or
counterclockwise to move forwards.
1
2The depth is adjustable within
3/16" (4mm).
Applicable for 30" Vacuum seal drawer only. The depth of the front panel of the drawer can be
adjusted to align with the surrounding cabinetry.

19
F the vacuum seal drawer is level and securely fitted to the cabinetry to
F any internal packaging has been removed from the drawer
F the isolating switch is accessible by the customer
F the bottom shelf can fully support the total weight of the combined appliances
F the transit screws are removed and discarded
F Open the drawer.
F Press the
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
button to turn the vacuum seal drawer on.
F Shut the drawer.
F Two LEDs in vacuum level indicators and two LEDs in sealing level indicators are
illuminated.
F Press the
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
button to turn the vacuum seal drawer off and shut the drawer.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
INSTALLER CHECKLIST
IMPORTANT!
Read all installation instructions in this manual to see if the unit has been correctly installed.
Ensure that installation has been completed correctly before use.
Ensure that: Test operation:

592227A 07.20
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2020. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.