Fisher & Paykel OR90SDBGFX3 User manual

First Use
Control Panel
1. Control buttons
2. Clock display
3. Temperature dial
4. Function dial
5. Front left (triple-ring wok) burner dial
6. Rear left (semi-rapid) burner dial
7. Central (dual) burner dial
8. Rear right (semi-rapid) burner dial
9. Front right (triple-ring) burner dial
10. Function indicator light
11. Temperature indicator light
Fig. 16 Control panel
Buttons
Sets the timer
Sets the cooking time
Sets the stop time for automatic cooking
Set the oven temperature / select Celsius
or Fahrenheit
Fig. 17 Clock display and control buttons
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90SDBGFX3/User_Guide_OR90SDBGFX…
Updated: Thu, 06 Apr 2023 09:56:35 GMT
Powered by
1

Decrease the time and temperature
Increase the time and temperature
Illuminated Symbols
If the display shows It means that... For more information
Flashing 12:00 The clock needs to be set. See instructions below.
Steadily lit The oven is set for automatic cooking
See section ‘Automatic Cooking’
Flashing and beeping Automatic cooking has finished
Steadily lit The timer is set See section ‘Using the Electronic Timer’
Steadily lit The oven is heating up See section ‘Using Your Oven’
To Set the Clock
When the power to the appliance is turned on or restored after a power failure 12:00 will flash in the display.
1. Press
and
together - the display will stop flashing. The clock is now set for 12:00.
2. Press
and
together again to change the time. The display will flash
3. Press
and
to set the time.
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90SDBGFX3/User_Guide_OR90SDBGFX…
Updated: Thu, 06 Apr 2023 09:56:35 GMT
Powered by
2

After a few minutes the display will be steadily lit, showing the time is set.
To Change the Time
1. Press
and
together. The display will flash
2. Press
and
to set the time.
After a few seconds the display will remain steadily lit, showing the time is set.
Remove the Side Racks to Fit the Catalytic Panels (if not already fitted)
1. Remove all shelves and trays.
2. For easier access to the fixing screws, you may remove the oven door first. See ‘Removing and refitting the
oven door’ in Care and Cleaning.
3. Remove the side racks on both sides:
4. Using a small coin or a flat-head screwdriver, loosen and remove both fixing screws.
5. Gently remove the side rack.
Fitting the Catalytic Panels
6. Fit the catalytic panel. When fitting the catalytic panel make sure that
• the arrows are pointing upwards
• the panel with the hole in it is on the right oven wall.
Refitting the Side Racks
7. To refit the side racks
• make sure that they are the right way up, as
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90SDBGFX3/User_Guide_OR90SDBGFX…
Updated: Thu, 06 Apr 2023 09:56:35 GMT
Powered by
3

in the illustrations, and that you tighten the
fixing screws.
8. If not already fitted, fit the telescopic sliding
shelf supports. See “Care and Cleaning’ for
instructions.
Fig. 18 Refitting the side racks
https://producthelp.fisherpaykel.com/eu/Cook/Freestanding_Cookers/Dual_Fuel/OR90SDBGFX3/User_Guide_OR90SDBGFX…
Updated: Thu, 06 Apr 2023 09:56:35 GMT
Powered by
4