Fisher & Paykel RF331T User manual

INSTALLATION GUIDE/USER GUIDE
NZ AU HK SG
ACTIVESMART™ REFRIGERATOR,
VERTICAL REFRIGERATOR
AND VERTICAL FREEZER
RF1T, RF81T, RF411T, RF440T, RF521T,
RF7, RF450, E450, RF08, RF88 & E88 models

1
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
fisherpaykel.com
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this User guide may
not be available in all markets and are
subject to change at any time. For current
details about model and specification
availability in your country, go to our
website fisherpaykel.com or contact your
local Fisher & Paykel dealer.
Model numbers 2
Introduction 3
Safety and warnings 4
Installation instructions 7
Moving or storing your appliance 13
ActiveSmart™ operating instructions 14
ActiveSmart™ special features 16
Activesmart™ cleaning care instructions 19
ActiveSmart™ user warnings and sounds 23
Vertical Refrigerator operating instructions 24
Vertical Refrigerator special features and maintenance 25
Vertical freezer operating instructions 26
Storing food in your refrigerator 27
Troubleshooting 28
Service & Warranty 32
CONTENTS

2
MODEL NUMBERS
ACTIVESMART™ REFRIGERATOR MODELS
635mm wide RF331T, RF381T, RF411T
680mm wide RF440T
790mm wide RF521T
VERTICAL REFRIGERATOR MODELS
635mm wide RF373, RF450, E450
VERTICAL FREEZER MODELS
635mm wide RF308, RF388, E388

3
INTRODUCTION
Thank you for buying a Fisher & Paykel ActiveSmart™ refrigerator.
At Fisher & Paykel we are very proud of this refrigerator. This refrigerator combines
sizeand storage space with the latest features and functions.
Thousands of hours of food care research and refrigeration experience has been
programmed into your refrigerator to give you the best possible performance.
We hope you enjoy your new refrigerator.
Note: this guide covers all models listed on previous page.
Diagrams above show examples of two of the models covered in this book.
ActiveSmart™ refrigerators have two handle options, shown below.
Recessed handlesDesigner handles
RF450
refrigerator
RF521T
refrigerator

4
!WARNING!
Electric Shock Hazard
Read and follow the safety and warnings outlined in this User guide
before operating this appliance.
Failure to do so can result in death, electric shock, fire or injury
topersons.
R600a
This refrigerator may contain flammable refrigerant isobutane(R600a).
Use this appliance only for the intended purpose as described in the User guide.
IMPORTANT SAFETY INSTRUCTIONS:
WARNING!
When using this appliance always exercise basic safety precautions including
thefollowing:
 Children should be supervised to ensure that they donot play with the appliance.
 Cleaning and user maintenance shall not be made bychildren without supervision.
 This appliance can be used by children aged from 8years and above and persons
withreduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in asafe way and understand the hazardsinvolved.
 The manufacturer’s installation instructions for product and cabinetry ventilation
mustbe followed when installing the appliance.
 To avoid hazard due to instability of the appliance, it must be fixed in accordance
withinstallation instructions.
 Keep ventilation openings, in the appliance enclosure or the built-in structure,
clearofobstruction.
 Do not use mechanical devices or other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
 Do not damage the refrigerant circuit.
 In case of damage to the refrigerant circuit, ventilate the area by opening all windows.
Do not operate electrical equipment or any other equipment that may produce arcs,
sparks or flames in the area. Contact your Fisher & Paykel trained and supported
service technician immediately to arrange for the appliance to be repaired.
 It is hazardous for anyone other than a Fisher & Paykel trained and supported service
person to service this appliance. In Queensland the service person must hold a gas
work licence or authorisation for hydrocarbon refrigerants to carry our service or
repairs which involve removal of covers.
SAFETY AND WARNINGS

5
Electrical
 This appliance must be installed in accordance with the installation instructions
beforeuse.
 To allow disconnection of the appliance from the supply after installation,
incorporatea switch in the fixed wiring in accordance with the local wiring rules.
 Never unplug your refrigerator by pulling on the power cord. Always grip the plug
firmly and pull straight out from the outlet.
 Do not plug in any other appliance at the same power point as your refrigerator or
use extension cords or double adapters.
 Repair or replace immediately all electric service cords that have become frayed
or otherwise damaged. Do not use a cord that shows cracks or abrasion along its
lengthor at either the plug or appliance end.
 If the power supply cord is damaged, it must only be replaced by your Fisher & Paykel
trained and supported service technician.
 When moving your appliance away from the wall, be careful not to roll over or
damage the power cord.
WARNING!
Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
IMPORTANT!
Your refrigerator is designed to operate for many years without the need for service
checks. However,ifyour refrigerator is malfunctioning, have it attended to by
your Fisher & Paykel trained and supported service technician as soon as possible.
Allelectrical repairs must be carried out by an adequately trained service technician
or qualified electrician.
Cleaning
 Use only soap based cleaning products.
 Many commercially available cleaning products contain solvents that may attack
theplastic components of your refrigerator and cause them tocrack.
 Avoid using anti-bacterial cleaning products on either the interior or exterior
of the cabinet as they may cause rusting of metal components and cracking of
plasticcomponents.
 Refer to the ‘Cleaning care instructions’ section of this User guide for your particular
model for further information.
Disposal
 Extreme care must be taken when disposing of your old appliance to avoid hazards:
– The flammable refrigerant gas must be safely removed by a qualified
servicetechnician.
– The thermal insulation foam in this appliance may contain flammable
insulationblowing gases, anyexposed foam may be highly flammable
andmustbe carefully treated during disposal.
– DANGER: The doors and panels should be removed and the shelves left
inplaceso that children may not easily climb inside.
 Consult your local energy authority or local codes as to the best way to dispose
ofyour old appliance.
 Your Fisher & Paykel trained and supported service technician will be able to give
advice on environmentally-friendly methods of disposing of your old refrigerator
orfreezer.
SAFETY AND WARNINGS

6
Storing food and drinks
 Do not store explosive substances such as aerosol cans with a flammable propellant
inthis appliance.
 Never store volatile or flammable materials in your refrigerator as they may explode.
 Never freeze liquids in glass containers. Liquid expands during freezing, which may
cause the container to explode.
 Never freeze carbonated drinks. They may explode.
SAFETY AND WARNINGS

7
Before installation
IMPORTANT!
 The appliance has front and rear rollers for moving the appliance forward and
backward. Do not move the appliance sideways to avoid damaging the rollers or
thefloor covering/surface.
 Connection to electrical power and earthing must comply with local codes
andordinances and be made by licensed personnel when required.
Avoid installation of the appliance/s under a ground fault circuit interrupter (GFCI).
 Ensure the appliance is installed properly. Improper installation that results in
appliance failure is not covered under the appliance warranty.
Check the installation location. Check the cabinetry. If using a kit to integrate your
product then check the dimensions of the cabinetry (width, depth, height, floor level,
finished alcove returns). Ensure that the ventiallation openings in the cabinetry are
clearof obstruction.
Check the power supply connection
 Ensure that there is a separate power socket for each appliance.
 Avoid sharing the power point with other appliances to prevent accidental
switching off of the appliance.
 For power requirements, please refer to the information on the serial plate.
 Ensure your appliance is properly grounded (earthed).
 Connect your appliance to an electrical supply with the fitted plug and lead.
 The appliance must be installed so the plug is accessible. For integrated appliance
(using our optional integrattion kit system) then we recommend to use an isolating
switch that is easily accessible to the user after the appliance is installed.
 Follow local codes and ordinances when installing the appliance.
Check your appliance
 Ensure that your appliance is the correct model as per your order.
 Check that the packaging is not damaged upon delivery.
 Ensure the components listed are complete.
IMPORTANT!
 Be careful when unpacking to prevent damage to the surface of your appliance.
 Ensure that the appliance is stable to prevent it tipping when unpacking.
INSTALLATION INSTRUCTIONS

8
INSTALLATION INSTRUCTIONS
Product and cabinetry dimensions
If integrating your refrigerator, please follow installation instructions provided with
theintegration kits.
RF373, RF450, E450, RF308, RF388, E388, RF331T, RF381T, RF411T, RF440T, RF521T
Flush with refrigerator chassis — full door rotation
Flush with refrigerator door — 90° door rotation
PLAN VIEW
FLUSH WITH REFRIGERATOR CHASSIS – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR - 90° DOOR ROTATION
D
A
BP C
Q
Q
Q
H/i
PG
M N
S
M
E
PM
FR
m o
j
p
k/l
PLAN VIEW
FLUSH WITH REFRIGERATOR CHASSIS – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR - 90° DOOR ROTATION
D A
BP C
Q
Q
Q
H/i
PG
M N
S
M
E
PM
FR
m o
j
p
k/l
PLAN VIEW
FLUSH WITH REFRIGERATOR CHASSIS – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR - 90° DOOR ROTATION
D A
BP C
Q
Q
Q
H/i
PG
MN
S
M
E
PM
FR
m o
j
p
k/l
PLAN VIEW
FLUSH WITH REFRIGERATOR CHASSIS – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR – FULL DOOR ROTATION
PLAN VIEW
FLUSH WITH REFRIGERATOR DOOR - 90° DOOR ROTATION
D A
BP C
Q
Q
Q
H/i
PG
M N
S
M
E
PM
FR
m o
j
p
k/l
Flush with refrigerator door — full door rotation

9
INSTALLATION INSTRUCTIONS
RF373
RF308
RF450
RF388
RF331T
RF381T
RF411T
RF440T
RF521T
PRODUCT DIMENSIONS mm
AOverall height of flat door product 1425 1695 1425 1595 1695 1695 1695
BOverall width of product 635 635 635 635 635 680 790
COverall depth of flat door product
(excludes handle, includes evaporator) 695 695 695 695 695 695 695
CABINETRY DIMENSIONS (including minimum clearances) mm
DInside height of cavity 1475 1700–
1735* 1465 1635 1700–
1735*
1700–
1735*
1700–
1735*
Flush with refrigerator chassis — full door rotation
EInside width 675 675 675 675 675 720 830
FInside depth 620 620 620 620 620 620 620
Flush with refrigerator door — full door rotation
GInside width 790 790 790 790 790 835 945
IInside depth flush to door –695 695 695 695 695 695
Flush with refrigerator door — 90° door rotation
(for full drawer/shelf access, the doors need to be open past 90°)
JInside width 745 745 745 745 745 790 900
LInside depth flush to door –695 695 695 695 695 695
Note: Alternative installation can cause some restriction to the refrigerator’s air supply and reduce its
optimum energy performance level. *1735 is recommended to provide the best ventilation
MINIMUM CLEARANCES mm
MSide clearance 20 20 20 20 20 20 20
NSide clearance — hinge side flush with
door — full rotation 135 135 135 135 135 135 135
OSide clearance — hinge side flush with
door — 90° rotation 90 90 90 90 90 90 90
PRear clearance (including evaporator tray) 30 30 30 30 30 30 30
QVent (above refrigerator cabinet or
around top of cupboard) 50 50 50 50 50 50 50
RDoor clearance — hinge side flush with
chassis — full rotation 520 520 520 520 520 555 645
SDoor clearance — hinge side flush with
door — full rotation 405 405 405 405 405 440 530

10
INSTALLATION INSTRUCTIONS
Installation
Your Fisher & Paykel refrigerator is fitted with frontand rear rollers,
designed for moving the product in the forwards and backwardsdirection.
Avoid moving the product in a sideways direction asthis may damage
the rollers or the floor covering/surface.
1Your refrigerator will arrive with the front feet
woundup making moving the product into its
finallocation a simple task.
2Roll the refrigerator into its final position
making surethere is the correct air gap
between the productand surrounding
cabinetry. See minimum clearance in cabinetry
dimensions table.
3Adjust the front feet down until the
refrigerator is leaning backward with the front
approximately 10mm higher than the back.
This will ensure a good door closing action.
4Aligning your refrigerator with cabinetry.
aAlign the sides of the refrigerator with
the cabinetry by adjusting the hinge side
frontfoot.
bAdjust the handle side foot until it touches
the floor and takes a small amount
ofweight.
cOnce the refrigerator is in place and
aligned with cupboards/alcove gently push
on the front top andcheck if the product
is rocking or stable.
Raise the front of
the refrigerator
Lower the front
of the refrigerator
Refrigerator feet

11
INSTALLATION INSTRUCTIONS
What to do if your product is unstable
5Gently push the refrigerator back until the
rearrollers contact the floor.
– Measure the gap under the front foot,
whichhascome off the floor.
– Obtain some solid packing material
(hardwood,plastic,etc) which fits firmly
intothegap under the foot.
Note: do not use metallic materials that may
corrode, stain and/or damage floor coverings.
6Wind both front feet up and roll the product
outofposition.
– Place the packing material in the location
diagonally opposite the front roller that
liftsoffthe floor.
– Make sure the packing material stays in place
when the product is pushed back into position.
– Ideally, the packing material is large enough
torest against the back wall so as to
preventitfrom moving when the cabinet
ispushed intoposition.
7Roll the refrigerator back into position and
adjustfront feet as per step 3. (Checkalignment
and door closing action are satisfactory).
– Make small adjustments to front feet
wherenecessary.
– Check that the product is stable
(all four feet are on the floor).
Ifnot,repeat steps4 c,5and6.
This foot lifts off the floor when
top front is gently pushed back
Example only
Unlevel floor
Unstable refrigerator
Wall behind refrigerator
For example: if this foot lifts off the floor when
pushing gently on the top front of the refrigerator
Packing material goes under rear roller
diagonally opposite front foot that lifts
Stabilising your refrigerator

12
INSTALLATION INSTRUCTIONS
Before placing food in the fresh food or freezer compartments
 Remove all internal packaging. Ensure that all transit clips are removed from the
refrigerator. These are small rubber stoppers located at the back of the shelves.
 Clean the inside of the appliance with a mix of warm water and a small amount of
liquiddetergent, and a soft cloth to remove manufacturing and transportation dust.
 Allow the refrigerator and freezer to run empty for 2 – 3 hours to allow each
compartment to cool to the appropriate temperature.
 The appliance may have an odour on its initial operation, but this will go when the
refrigerator and freezer have cooled sufficiently.
Energy efficiency
For the most energy efficient use of your appliance:
 Ensure your refrigerator has adequate ventilation.
 Do not cover your appliance with any material that will prevent air from flowing
aroundthe cabinet sides.
 Ensure you vacuum around the appliance to remove dust and possible pet hair
accumulation. Also keep the appliance and it’s cabinetry free of dust by wiping
downwith a dry, lint-free cloth (refer to sections ‘Cleaning care instructions’,
‘Cabinetsurround’ for your specific model).
 Allow good clearances in front of air ducts within the cabinet for maximum cold
airdistribution.
 Cool hot foods before placing them in the appliance.
 Do not overfill the compartments.
 Keep door openings to a minimum.
 Select a temperature setting that isn’t too cold.
 Check your door seals for leaks.

13
If your refrigerator is turned off for any reason, wait 10minutes before turning it back on.
This will allow the refrigeration system pressures to equalise before restarting.
Moving your refrigerator
 Turn off the appliance and unplug from the power point. Remove all food.
 Turn the adjustable feet to the right as far as they will turn.
 Ease the refrigerator out of its position. Tuck the power cord away, tape the shelves
in place and tape the doors closed. If the cabinet needs to be placed at an angle or
laiddown, carefully lay it on its side (the right hand side when viewed from the front).
 Relocate and install. If the appliance has been left on its side for any length of time,
leave it standing upright as long as you can (a few hours) before turning on.
Storing your refrigerator
 When storing your cleaned appliance, leave the doors open. This allows air to circulate
and prevents the build up of bacteria and moulds.
 Before using again, clean well using a mixture of warm water and a small amount of
liquid dishwashing detergent. Rinse with clean water and dry with a soft lint-free cloth.
Holiday time
We recommend you leave your refrigerator operating while you are on holiday.
MOVING OR STORING YOUR APPLIANCE

14
ACTIVESMART™ OPERATING INSTRUCTIONS
Models: 635mm wide RF331T, RF381T, RF411T
680mm wide RF440T
790mm wide RF521T
The control panel enables you to view and modify features and options on your refrigerator.
Temperature control
 When the refrigerator is first turned on, the powerful cooling system will automatically
cool both refrigerator and freezer compartments to their set temperatures.
Thiswilltakebetween 2 – 3hours.
 The two compartment temperatures are accurately and independently controlled
anddonot change with the temperature or humidity of the surroundings;
whethersummer or winter.
 If you wish to alter the temperature of either the fresh food compartment or
freezercompartment, this can be easily done by using the internal control panel
locatedon theback wall of the refrigerator compartment.
Control panel (to adjust temperatures)
Increase temperature button
Decrease temperature button
Temperature indicator (thermometer)
Fresh food and freezer
compartment indicator
Compartment
select button
Fresh food compartment
 The fresh food compartment light will automatically be illuminated.
Thetemperatureforthis compartment will show as a series of lights.
 The temperature may be altered by pressing the or buttons.
One press on either of these buttons will reduce or increase the number
oflightsbyonewhich indicates a small change in temperature.
 Fewer lights illuminated means a cooler temperature for the
compartment selected.

15
ACTIVESMART™ OPERATING INSTRUCTIONS
Freezer food compartment
 To adjust the freezer temperature press the button so the freezer compartment
lightis illuminated.
 The freezer temperature can be altered by pressing the
or buttons.
 One press on either of these buttons will reduce or increase the number of lights
illuminated which indicates a small change in temperature.
 Fewer lights illuminated means a cooler temperature for the compartment selected.
Note: successively pressing the button will automatically scroll between the
compartments.
 When the door is re-opened the control panel will return automatically to the fresh
foodcompartment setting.
Door alarms
 If the fresh food compartment door is left open the alarm will beep after 90seconds
and if the freezer door is left open the alarm will beep after 60seconds.
 While either door remains open, subsequent beeps will sound every 30seconds for
5minutes.
 A continuous alarm will sound if either of the doors have been left open for 5minutes
orlonger and the interior compartment light(s) will turn off. The alarm will stop only
when the door(s) is closed.
Sabbath mode
 To activate Sabbath mode, open both the fresh food and freezer compartment doors
and then hold the button on the temperature control panel for 10seconds.
 Both the fresh food and freezer compartment indicators will be illuminated indicating
the refrigerator is in Sabbath mode.
When the product is in Sabbath mode:
 The fresh food and freezer compartment indicator lights will be illuminated.
 The light will not operate when the door is opened.
 The door alarm will not operate.
 The display will not function except to indicate Sabbath mode is active as stated above.
 Opening the door will not affect the compressor or fans.
 If the power to the refrigerator is turned off whilst in this mode, the product will
continue in Sabbath mode when the power is restored.
 Sabbath mode will automatically de-activate 80hours after activation.
 To de-activate earlier than 80hours hold the button on the temperature control
panel for 10seconds.

16
ACTIVESMART™ SPECIAL FEATURES
Manual ice system (selected models only)
An ice storage bin which sits inside the upper top freezer bin provides storage for
andgives you access to clean, clear ice cubes.
Upper left freezer bin, ice storage bin, ice tray,
lid and scoop in correct position
Accessing your ice
Information about your manual ice system
 To make ice, take the ice tray and lid from the top of the ice storage bin.
Remove the lid from the ice tray and fill the tray with water. Place the lid back
on the ice tray and carefully position it back onto the ice storage bin.
 Once the ice is solid, take the ice tray and lid off the ice storage bin, remove the
lidfromthe tray and twist the ice tray at each end in opposite directions.
Turn the ice tray over the ice storage bin to dislodge the cubes into the bin.
 Fill the ice tray with clean water and repeat to fill the ice storage bin.
 Attached to the ice storage bin is the ice scoop which provides hygienic access to ice.
 To access ice cubes, take the ice tray and lid from the top of the ice storage bin and
place onto a flat surface. Take the scoop from the front of the bin, scoop cubes into
vessel and then replace the scoop, tray and lid back to the top of the bin.
 For maximum ice storage, level the stored cubes around the bin with the ice scoop.
 If ice is not used often, old cubes will become cloudy, taste stale, will shrink and
maystick together. Empty the ice storage bin periodically and wash in lukewarm water.
Drythoroughly and place back in the correct position.

17
ACTIVESMART™ SPECIAL FEATURES
Fruit and vegetable bins and humidity control lid
The fruit and vegetable bins feature a unique lid which provides two functions:
 The humidity lid seals the bins and provides a humid microclimate to extend storage
times of fruit and vegetables.
 The humidity lid prevents condensation, which forms at high humidities, from dripping
down onto the fruit and vegetables by retaining it in the grooves of the lid.
Fruit and vegetable bins and humidity slide (selected models only)
 Each fruit and vegetable bin has a humidity slide control that can be adjusted to
afruitor vegetable setting depending on what is stored in the bins.
 If possible try to store fruit and vegetables separately. This will help extend their
storagelife.
 If there is a mixture of fruit and vegetables in the bin adjust the position of the
controlto thecentre.
 If there is too much water in the bins (due to the high humidity in the bins), the
controlcan be adjusted towards the setting with fewer drips (fruit setting) and/or
thewater canbe wiped out as required.
 Remember a minimum amount of water in the bins is beneficial for fruit and
vegetablestorage.
Humidity control graphic
Salad
greens
Mixed fruit
& vegetables
Fruit with
skin/peel
Lettuce
Spinach
Broccoli
Cabbage
Carrots
Oranges
Lemons
Limes
SUITABLE FOR:

18
ACTIVESMART™ SPECIAL FEATURES
Vegetable bin divider instructions (where fitted)
To fit the divider, insert divider into bin on an angle, straighten and slot into place.
Toadjust the divider, fully extend the bin, partially lift the divider, slide sideways
andre-slot into position.
Vegetable bin divider
Bottle holder (where fitted)
 The bottle holders can be used to store a variety of bottles.
 To position the bottle holder in your refrigerator, simply slot the back edge of the
bottleholder onto the back trim of any shelf in the fresh food compartment.
 If you are not using all or some of the bottle holders, the unused bottle holders can be
stacked up on top of one another so they do not take up unnecessary shelf space.
 Bottles are best stored with the neck of the beverage facing the front of the refrigerator.
Glass shelves
 Glass shelves can be repositioned in the cabinet as desired.
 Remove shelves by lifting up the back of the shelf and then pulling the shelf forward.